Brother HL-660 manual Regulations, Laser Safety For 110-120 V Model Only

Page 7

English

REGULATIONS

REGULATIONS

Federal Communications Commission Compliance Notice (For USA Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

❏Reorient or relocate the receiving antenna.

❏Increase the separation between the equipment and receiver.

❏Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

❏Consult the dealer or an experienced radio/TV technician for help.

Important – About the Interface Cable

This printer has been certified to comply with FCC standards, which are applied to the U.S.A. only. A shielded interface cable should be used according to FCC 15.27(C). In addition, a grounded plug should be plugged into a grounded AC outlet after checking the rating of the local power supply for the printer to operate properly and safely.

Caution

Changes or modifications not expressly approved by Brother Industries, Ltd. could void the user’s authority to operate the equipment.

Laser Safety (For 110–120 V Model Only)

This printer is certified as a Class I laser product under the U.S. Department of Health and Human Services (DHHS) Radiation Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This means that the printer does not produce hazardous laser radiation.

Since radiation emitted inside the printer is completely confined within protective housings and external covers, the laser beam cannot escape from the machine during any phase of user operation.

Radio Interference (For 220 - 240 V Model Only)

This apparatus complies with EN55022 (CISPR Publication 22) / Class B.

v

Image 7

Contents Brother Laser Printer HL-660 SeriesShipment of the Printer For USA & Canada Only Laser Printer HL-660 Series User’s GuideCompilation and Publication Notice TrademarksTable of Contents Options Regulations Laser Safety For 110-120 V Model OnlyRadio Interference For 220 240 V Model Only FDA Regulations For Your SafetyDisconnect device IEC 825 Laser Class For 220-240 V Model OnlyManufactured at Important For U.K. only Canadian Department of Communications Compliance StatementEnglish About the Guidebooks Learning How to Use the PrinterDefinitions of Warnings, Cautions, and Notes Printer Overview About Your PrinterDpi Resolution and 6ppm Printing Speed FeaturesBi-Directional Parallel Interface APT Advanced Photoscale Technology Operating and Storage Environment Power SupplyEnvironment English Chapter Paper Handling Paper SpecificationsFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Opening the Feeder Loading Paper or Envelope in the Feeder Loading Paper into the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Opening the Output Tray Extending the Paper Support Wire Output Tray and Paper Support WireReady Lamp LampsData Lamp Alarm LampManual Lamp Select Reset Switch SwitchesSelect Switch Test Switch FF/CONTTEST SwitchReset Switch FF/CONT SwitchReprint Function Sleep ModeData Test Print ModeReset/Hex Dump Mode APT Advanced Photoscale Technology ProtectionBR-SCRIPT 2 ROM Board Chapter OptionsAppletalk Interface Board Minimum Memory Recommendation including resident memory Additional MemoryEnglish Unplug the power cord Disconnect the interface cable Installing the SimmInstall the Simm Replacing the Toner Cartridge Chapter MaintenanceRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Removing the Toner Cartridge Replacing the Drum UnitInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit 14 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer15 Inside the printer Cleaning the Printer Interior and Drum Unit17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire RE-PACKING the Printer 19 Removing the Drum Unit Assembly21 Repacking the Printer English Operator Calls Alarm Indications AT a GlanceEnglish Service Calls Locating Paper Jam Position Paper JamsPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer for DOS Setting up the Printer HardwareSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Recommendations Paper HandlingPrinting White Stripes or Faint Images Print QualityDark Stripes or Toner Stains 11 Scattering Toner 13 Stained at Fixed Interval English Appendices Printer SpecificationsElectrical and Mechanical FunctionsParallel Interface Specification Fig. A-1 Parallel interface cable Intellifont Compatible Fonts Resident FontsBitmapped Fonts Scalable FontsAppendix-6 Epson Mode Symbol SETS/ Character SetsOCR Symbol Sets HP LaserJet 4 ModeHP LaserJet HP LaserJet 4, Epson FX-850, IBM Propritner XL Appendix-10 Index Simm III UL5580001