Brother HL-660 manual FDA Regulations, For Your Safety

Page 8

English

USER’S GUIDE

FDA Regulations

U.S. Food and Drug Administration (FDA) implemented regulations for laser products manufactured from August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States. The label shown on the back of the printer indicates compliance with the FDA regulations and must be attached to laser products marketed in the United States.

MANUFACTURED: BROTHER INDUSTRIES, LTD.

15-1 Naeshiro-cho Mizuho-ku Nagoya, 467 Japan

This product complies with FDA radiation performance standards, 21 CFR Subchapter J

Caution

Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous invisible radiation exposure.

For Your Safety

To ensure safe operation the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively grounded through the normal household wiring.

Extension cords used with the equipment must be three-conductor and be correctly wired to provide connection to ground. Incorrectly wired extension cords are a major cause of fatalities.

The fact that the equipment operates satisfactorily does not imply that the power is grounded and that the installation is completely safe. For your safety, if in any doubt about the effective grounding of the power, consult a qualified electrician.

DECLARATION OF CONFORMITY (EUROPE)

We, Brother International Europe Ltd.,

Brother House 1 tame Street, Guide Bridge, Audenshaw, Manchester M34 5JE, UK.

declare that this product is in conformity with the following normative documents:

Safety:	EN 60950,	EN 60825
EMC:	EN 55022 Class B,	EN 50082-1

following the provisions of the Low Voltage Directive 73/23/EEC and the Electromagnetic Compatibility Directive 89/336/EEC (as amended by 91/263/EEC and 92/31/EEC).

Manufacture at the following facilities is carried out under a Quality System which is registered by BSI Quality Assurance and JQA Quality Assurance.

Brother Industries, Ltd., Kariya Plant

1-5, Kitajizoyama, Noda-cho, Kariya-shi,

Aichi-ken 448, Japan.

BSI Certificate of Registration No. FM27391

JQA Certificate of Registration No. 0340

Issued by :

Brother International Europe Ltd.

European Development and Technical Services Division

vi

Image 8

Contents HL-660 Series Brother Laser PrinterShipment of the Printer Laser Printer HL-660 Series User’s Guide For USA & Canada OnlyTrademarks Compilation and Publication Notice Table of Contents Options Radio Interference For 220 240 V Model Only Laser Safety For 110-120 V Model OnlyRegulations For Your Safety FDA RegulationsManufactured at IEC 825 Laser Class For 220-240 V Model OnlyDisconnect device Canadian Department of Communications Compliance Statement Important For U.K. onlyEnglish Definitions of Warnings, Cautions, and Notes Learning How to Use the PrinterAbout the Guidebooks About Your Printer Printer OverviewFeatures Dpi Resolution and 6ppm Printing SpeedBi-Directional Parallel Interface APT Advanced Photoscale Technology Environment Power SupplyOperating and Storage Environment English Paper Specifications Chapter Paper HandlingFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelope in the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Output Tray and Paper Support Wire Opening the Output Tray Extending the Paper Support WireLamps Ready LampManual Lamp Alarm LampData Lamp Select Switch SwitchesSelect Reset Switch FF/CONTTEST Switch Reset SwitchFF/CONT Switch Test SwitchSleep Mode Reprint FunctionTest Print Mode DataReset/Hex Dump Mode Protection APT Advanced Photoscale TechnologyChapter Options BR-SCRIPT 2 ROM BoardAppletalk Interface Board Additional Memory Minimum Memory Recommendation including resident memoryEnglish Installing the Simm Unplug the power cord Disconnect the interface cableInstall the Simm Chapter Maintenance Replacing the Toner CartridgeRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Removing the Toner CartridgeInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit Adjusting the Print Density 14 Adjusting the Print Density DialCleaning the Printer Cleaning the Printer ExteriorCleaning the Printer Interior and Drum Unit 15 Inside the printer17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire 19 Removing the Drum Unit Assembly RE-PACKING the Printer21 Repacking the Printer English Alarm Indications AT a Glance Operator CallsEnglish Service Calls Paper Jams Locating Paper Jam PositionPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer Hardware Setting up the Printer for DOSSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Paper Handling RecommendationsPrinting Print Quality White Stripes or Faint ImagesDark Stripes or Toner Stains 11 Scattering Toner 13 Stained at Fixed Interval English Printer Specifications AppendicesFunctions Electrical and MechanicalParallel Interface Specification Fig. A-1 Parallel interface cable Resident Fonts Bitmapped FontsScalable Fonts Intellifont Compatible FontsAppendix-6 Symbol SETS/ Character Sets OCR Symbol SetsHP LaserJet 4 Mode Epson ModeHP LaserJet HP LaserJet 4, Epson FX-850, IBM Propritner XL Appendix-10 Index Simm III UL5580001