Brother HL-660 manual Alarm Indications AT a Glance, Operator Calls

Page 59

English

CHAPTER 6 TROUBLESHOOTING

CHAPTER 6

TROUBLESHOOTING

ALARM INDICATIONS AT A GLANCE

Operator Calls

If an error occurs, the printer indicates an ‘operator call’ by blinking the

ALARM lamp and any of the following lamps.

Find the error and take the proper action to correct it. The printer automatically recovers from most errors, but you may need to reset the printer with the switches as described below.

Blinking Lamp	Error
PAPER ❍↔●	Paper jam
ALARM❍↔●
	Paper empty
	Mis Feed

COVER ❍↔●	Cover open
ALARM❍↔●

TONER ❍↔●	Toner low
ALARM❍↔●
( every 5 seconds)
TONER ❍↔●	Toner Empty
ALARM❍↔●

Action

Clear the paper jam referring to the next section “PAPER JAMS” and press the FF/CONT switch if the printer does not automatically resume printing.

Load paper into the printer referring to Chapter 2 and press the FF/CONT switch.

Reinstall the paper and press the FF/CONT switch.

Close the top cover of the printer or press firmly on the multi-purpose sheet feeder to make sure it is properly installed.

Indicates that the printer has approximately 100 pages of printing left before the toner cartridge is empty.

Replace the toner cartridge with a new one.

❍OFF ● ON

6–1

Image 59

Contents Brother Laser Printer HL-660 SeriesShipment of the Printer For USA & Canada Only Laser Printer HL-660 Series User’s GuideCompilation and Publication Notice TrademarksTable of Contents Options Radio Interference For 220 240 V Model Only Laser Safety For 110-120 V Model OnlyRegulations FDA Regulations For Your SafetyManufactured at IEC 825 Laser Class For 220-240 V Model OnlyDisconnect device Important For U.K. only Canadian Department of Communications Compliance StatementEnglish Definitions of Warnings, Cautions, and Notes Learning How to Use the PrinterAbout the Guidebooks Printer Overview About Your PrinterDpi Resolution and 6ppm Printing Speed FeaturesBi-Directional Parallel Interface APT Advanced Photoscale Technology Environment Power SupplyOperating and Storage Environment English Chapter Paper Handling Paper SpecificationsFan the Paper Straighten the Paper Printable Area MULTI-PURPOSE Sheet Feeder Opening the Feeder Loading Paper or Envelope in the Feeder Loading Paper into the FeederMoving the Paper Guide Closing the Feeder Two Side Printing Manual Duplexing Manual Feed Slot Moving the Paper Guide Opening the Output Tray Extending the Paper Support Wire Output Tray and Paper Support WireReady Lamp LampsManual Lamp Alarm LampData Lamp Select Switch SwitchesSelect Reset Switch Test Switch FF/CONTTEST SwitchReset Switch FF/CONT SwitchReprint Function Sleep ModeData Test Print ModeReset/Hex Dump Mode APT Advanced Photoscale Technology ProtectionBR-SCRIPT 2 ROM Board Chapter OptionsAppletalk Interface Board Minimum Memory Recommendation including resident memory Additional MemoryEnglish Unplug the power cord Disconnect the interface cable Installing the SimmInstall the Simm Replacing the Toner Cartridge Chapter MaintenanceRemoving the Multi-Purpose Sheet Feeder Remove the old toner cartridge from the printer Installing the Toner Cartridge Into the Drum Unit Removing the Toner Cartridge Replacing the Drum UnitInside the printer Remove the protective parts ① ⑥ in order as shown below 13 Installing the Drum Unit 14 Adjusting the Print Density Dial Adjusting the Print DensityCleaning the Printer Exterior Cleaning the Printer15 Inside the printer Cleaning the Printer Interior and Drum Unit17 Cleaning the Printer Interior 18 Cleaning the Primary Corona Wire RE-PACKING the Printer 19 Removing the Drum Unit Assembly21 Repacking the Printer English Operator Calls Alarm Indications AT a GlanceEnglish Service Calls Locating Paper Jam Position Paper JamsPaper Jam in the Feeder Paper Jam Inside the Printer Setting up the Printer for DOS Setting up the Printer HardwareSetting up the Printer for Windows Setting up the Printer for Apple Macintosh Computers Recommendations Paper HandlingPrinting White Stripes or Faint Images Print QualityDark Stripes or Toner Stains 11 Scattering Toner 13 Stained at Fixed Interval English Appendices Printer SpecificationsElectrical and Mechanical FunctionsParallel Interface Specification Fig. A-1 Parallel interface cable Intellifont Compatible Fonts Resident FontsBitmapped Fonts Scalable FontsAppendix-6 Epson Mode Symbol SETS/ Character SetsOCR Symbol Sets HP LaserJet 4 ModeHP LaserJet HP LaserJet 4, Epson FX-850, IBM Propritner XL Appendix-10 Index Simm III UL5580001