Mitsubishi Electronics RV-6S instruction manual Turning on the control power

Page 23

2Unpacking to Installation

2.3.2Setting the origin with the origin data input method

(1) Confirming the origin data

Origin data history table (Origin Data History) Serial No.ES804008

 

Date

Default

. . .

. . .

. . .

 

 

 

 

 

 

 

 

 

 

 

 

 

V!#S29

 

 

 

 

 

 

 

 

 

06DTYY

 

 

 

 

 

 

 

 

 

2?HL9X

 

 

 

 

 

 

 

 

 

1CP55V

 

 

 

 

 

 

 

 

 

T6!M$Y

 

 

 

 

 

 

 

 

 

Z2IJ%Z

 

 

 

 

 

 

 

 

 

A12%Z0

 

 

 

 

 

 

 

 

Method

E ・ N ・ S P

E ・ N ・

E ・ N ・ S P

 

 

 

 

S P

 

 

 

 

 

 

 

 

 

(O: AlphabetO, 0: Zero)

 

 

Note) Meanings of symbols in method column

E:Jig method

N:Not used SP: Not used

Fig.2-8 : Origin data label (an example)

The origin data to be input is noted in the origin data sheet enclosed with the arm, or on the origin data history table attached to the back side of the shoulder coverB. (Refer to Fig. 2-8).

Referring to "5.3.2 Installing/removing the cover" on page 44, remove the shoulder coverB, and confirm the value.

The value given in the default setting column is the origin settings set with the calibration jig before shipment.

WARNING Always install/remove the cover with the controller control power turned OFF. Failure to do so could lead to physical damage or personal injury should the robot start moving due to incorrect operations.

(2) Turning ON the control power

CAUTION Confirm that there are no operators near the robot before turning the power ON.

1)Turn the controller [POWER] switch ON.

The control power will be turned ON, and " □ . 100" will appear on the STATUS NUMBER display on the front of the controller.

Setting the origin 2-13

Image 23 Contents
Mitsubishi Supplemental Instruction Change of the lubrication method and notes Robot front Safety Precautions Page Revision history Page Contents Appendix-66 Before starting use Symbol Meaning Safety Precautions 4Safety Precautions Part name Type Qty Remarks Unpacking to Installation Confirming the productUnpacking InstallationTransportation procedures Transporting with a crane Installation procedures Grounding procedures Grounding procedures Grounding methodsCN2 CN1 Connecting with the controllerHook Projection Remove T/B switch Setting the originInstalling the teaching pendant T/B Installing with the control power OFFTurning on the control power Operating from the T/B When T/B operations are mistakenPreparing the T/B Selecting a menu Selecting the origin setting methodChanges to Origin Inputting the origin dataCorrecting an input Installing the shoulder coverBMoving the cursor Inputting charactersJ1 axis Confirming the operation+ J4 axis J5 axisControl point - + Control point +X+YRadius Arc Control point +X+Y + J4 J6 - Control point +X+YJ2 axis When the robot is in the transportation postureJoint jog operation - + J1 axisJ4 axis When an XX appears on the T/B screen displayJ3 axis J6 axis +XYZ jog operation Tool length When alarm No occursTool jog operation 26Confirming the operation Axis XYZ jog operation Jog mode will change when only XYZ key is pressed again28Confirming the operation Arc Cylnder jog operation+X - - +Section a View B View CNo.2 arm View from No arm cover B side No.2 arm Port View D Installing the hand input cableInstalling the hand output cable Axis Standard Alternative angle Changing the operating range3Installing the option devices Basic operations Maintenance and inspection interval Maintenance and InspectionDaily inspection items Inspection itemsPeriodic inspection Battery onRobot arm structure Maintenance and inspection proceduresMaintenance and inspection procedures : Installing/removing the cover Installing/removing the cover: Cover names Timing belt replacement period Inspection, maintenance and replacement of timing beltMark M4×12(Socket bolt) 5Timing pulley 4Timing pulley : Slack Timing belt tensionView from a Lubrication Lubrication position and specificationsLubrication method : Lubrication specificationsReplacing the robot arm battery Replacing the backup batteryPart name Type Usage place Qty Supplier Maintenance partsMethod Explanation Remarks Resetting the originJig method Origin setting axis designation Diagram of the robot viewed from the top56Resetting the origin J3 axis origin setting 58Resetting the origin J5 axis origin setting 60Resetting the origin User origin method 62Resetting the origin J6 axis J5 axis J1 axis J2 axis ABS mark View aABS origin method J4 axis J3 axis64Resetting the origin Recording the origin data RIGHT/LEFT Appendix Appendix 1 : Configuration flagConfiguration flag Appendix-67 Specifications are subject to change without notice