Mitsubishi Electronics RV-6S instruction manual Change of the lubrication method and notes

Page 3

3.Change of the lubrication method and notes

Details of change and supplement

A procedure and precautions applicable to the products affected by the change were added to “(2) Lubrication method” on P5-50. The procedure applicable to the products affected by the change is described below. When lubricating all other products, follow the original procedure specified in the instruction manual.

(1)Lubrication method of products affected by the change

1)Set the robot to the posture shown in Fig. 5-6.

2)Refer to the "5.3.2Installing/removing the cover" on page 44 and remove the covers.

3)Insert the grease shown in Table 5-5 using a grease gun of manual type from the lubrication grease nipple.

4)Replace the covers with the removal procedure in reverse.

(2)Precautions for lubrication

Take note of the following points when lubricating all products, regardless of whether or not they are affected by the change.

CAUTION	Use manual grease gun, and inject grease with pressure 0.03Mpa or less. Do not
CAUTION	use the grease gun, which derived by the factory air presser to
	avoid injecting by too high pressure.

BFP-A8323-A01-A

Image 3

Contents Mitsubishi Supplemental Instruction Change of the lubrication method and notes Robot front Safety Precautions Page Revision history Page Contents Appendix-66 Before starting use Symbol Meaning Safety Precautions 4Safety Precautions Part name Type Qty Remarks Unpacking to Installation Confirming the productUnpacking InstallationTransportation procedures Transporting with a crane Installation procedures Grounding procedures Grounding procedures Grounding methodsCN2 CN1 Connecting with the controllerHook Projection Remove T/B switch Setting the originInstalling the teaching pendant T/B Installing with the control power OFFTurning on the control power When T/B operations are mistaken Preparing the T/BOperating from the T/B Selecting a menu Selecting the origin setting methodChanges to Origin Inputting the origin dataCorrecting an input Installing the shoulder coverBMoving the cursor Inputting charactersJ1 axis Confirming the operation＋ J4 axis J5 axisControl point －＋ Control point ＋X＋YRadius Arc Control point ＋X＋Y ＋ J4 J6 － Control point ＋X＋YJ2 axis When the robot is in the transportation postureJoint jog operation －＋ J1 axisJ4 axis When an XＸ appears on the T/B screen displayJ3 axis J6 axis ＋XYZ jog operation Tool length When alarm No occursTool jog operation 26Confirming the operation Axis XYZ jog operation Jog mode will change when only XYZ key is pressed again28Confirming the operation Arc Cylnder jog operation＋X －－＋Section a View B View CNo.2 arm View from No arm cover B side No.2 arm Port View D Installing the hand input cableInstalling the hand output cable Axis Standard Alternative angle Changing the operating range3Installing the option devices Basic operations Maintenance and inspection interval Maintenance and InspectionDaily inspection items Inspection itemsPeriodic inspection Battery onRobot arm structure Maintenance and inspection proceduresMaintenance and inspection procedures ： Installing/removing the cover Installing/removing the cover： Cover names Timing belt replacement period Inspection, maintenance and replacement of timing beltMark M4×12（Socket bolt） 5Timing pulley 4Timing pulley ： Slack Timing belt tensionView from a Lubrication Lubrication position and specificationsLubrication method ： Lubrication specificationsReplacing the robot arm battery Replacing the backup batteryPart name Type Usage place Qty Supplier Maintenance partsMethod Explanation Remarks Resetting the originJig method Origin setting axis designation Diagram of the robot viewed from the top56Resetting the origin J3 axis origin setting 58Resetting the origin J5 axis origin setting 60Resetting the origin User origin method 62Resetting the origin J6 axis J5 axis J1 axis J2 axis ABS mark View aABS origin method J4 axis J3 axis64Resetting the origin Recording the origin data RIGHT/LEFT Appendix Appendix 1 ： Configuration flagConfiguration flag Appendix-67 Specifications are subject to change without notice