ADTRAN 600 Series user manual RFC 1483 Bridge, PPPoATM

Page 40

The connection will not allow the PPP peer to authen- ticate it.

The connection can be authenticated using PAP, CHAP or EAP.

The connection can be authenticated using CHAP or EAP only.

The connection will only allow authentication by the peer using EAP.

Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B Page 40

PRIVATE ADDRESS

MODE

PRIVATE PORT

MODE

TRANSLATE BODY

NAT VIEW

NAPT ADDRESS

ENTRY COUNT

ENTRY OVERFLOW

COUNT

RIP

The private IP address can be specified to steer certain protocols and ports to specific servers in the private network. Likewise, internal hosts can be steered to certain servers on the public network. A new request from the public network matching this entry’s public parameters will be dropped if this mode is set to ;!.

The private destination port associated with this entry can be specified to add more control over certain types of traffic. Leave as ;1 to cover all port types.

By default, the application payload in the packet is scanned for occurrences of the private/public IP address in binary or ASCII form. Set this to for applications where this will cause problems.

Shows the protocols that are actively being translated.

Represents the public address that is being used as the NAPT address.

The number of entries in the NAT table.

A count of the dropped entries due to low memory.

Use this menu to enable RIP on the WAN interface. (See RIP on page 37 for description of options.)

RFC 1483 Bridge

This is used to enable bridge mode on this PVC. (These settings only take effect when RFC 1483 is the selected protocol.)

PPPoATM

The Total Access 600 uses the PPPoATM profile to specify the profile used when connected using PPP.

Authentication

The authentication menu contains the required parameters for the authentication of the PPP peer and for being authenticated by the PPP peer. Authentication is applied between the Total Access 600 and the PPP peer as follows:

TX Method

This parameter specifies how the Total Access 600 is to be authenticated by the PPP peer. There are four possible selections.

NONE (def)

PAP, CHAP, OR EAP

CHAP OR EAP

EAP

Total Access 600 Series User Manual

© 2002, ADTRAN, Inc.

Image 40

Contents Total Access 600 Series Shdsl IAD Trademarks To the Holder of the ManualSafety Instructions 2002, ADTRAN, Inc 2002, ADTRAN, Inc 2002, ADTRAN, Inc Warranty and Customer Service Limited Product WarrantyRepair and Return Customer Service, Product Support Information, and TrainingPre-Sales Inquiries and Applications Support Post-Sale Support Installation and Maintenance SupportTraining Total Access 600 Series Shdsl IAD User Interface Guide +@A1 +@&.&$$ +@,%.% @/& % @/& %.&$$ @.&$$ @/1 @.%+0% %B,% ##%B 8= $*+*$&,$&-# # #$% Figures Firmware Updates Analog LifelineVoice Over DSL Overview Voice over DSL System Info Bootcode Revision Part NumberSerial Number Firmware RevisionSystem Config Network Timing ModeTelnet Access Telnet User ListPassword Protect Instructions for Changing Passwords Step ActionMaint Port Menu LevelNetwork Time Upgrade Firmware System UtilityConfig Transfer Ping Configuring WAN Settings ATM ConfigDslam Type Layer One InterfaceATM Stats Data ScramblingAP Receive Cell Errors AP Rx CellsAP Rx OAM Cells AP Receive Cells DiscardedAAL5 Receive Errors AAL5 Receive Discarded FramesAAL5 No ATM Frames AAL5 No Data PacketsConfiguring the Router Configuration GlobalText string used to represent the domain name Bridge Security Dotted decimal format2002, ADTRAN, Inc Ethernet Ethernet MenuUse this menu to enable RIP on the LAN interface MAC AddressWAN This selection enables IP on this PVC RFC 1483 Bridge PPPoATMThis is the username used to authenticate the PPP peer Only routes not learned on the WAN connection This is the PPP encapsulation. LLC or VC-Mux Configuring the Router Status Router/Status MenuConfiguring the Router Logs Sys log Host PPP LogConnection Log Network LogConfiguring Voice Support Config Call ControlConfiguring Voice Support Status Gateway StatsPVC Stats Pots StatsMenu Managing the Modules ModulesTest FXS Configuration Managing the Modules V.35 SetupMode Following settings are used for FRF5 Following settings are used for FRF8 Appendix A. Updating Total Access 600 Firmware using Xmodem Updating Firmware via a Forced DownloadPress $until a menu appears Updating Firmware via the Console Menus When prompted, press to erase flashSelect -# # for #9 Appendix B. Updating Total Access 600 Firmware using Tftp Message Meaning Message Meaning Menu Path Left Pane Status Bar ModeSystem Time Window Pane Navigation Right Window Pane NotationAdditional Terminal Menu Window Features Navigating Using the Keyboard KeysSession Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix E. RFC1483 Quick Start IP Routing IP Routing Step Action Appendix F. RFC1483 Quick Start IP Routing with NAT OptionsAppendix G. RFC1483 Quick Start Bridging Bridging Step ActionAppendix H. Craft Port Connection Pin-out 2002, ADTRAN, Inc