ADTRAN 600 Series user manual Appendix G. RFC1483 Quick Start Bridging, Bridging Step Action

Page 70

Total Access 600 Series SHDSL IAD User Interface Guide/64200683L1-31B

Page 70

Appendix G. RFC1483 Quick Start (Bridging)

The Total Access 600 allows for complete integration of voice and data delivery from one compact platform. Once you have completed the voice turn up procedure from the previous example, adding data to the circuit requires some additional setup.

To configure a Total Access 600 for Bridging, you need to know the VPI and VCI values for the data circuit on your network.

Bridging

Step

Action

 

 

1

From the Total Access 600 main menu, select the WAN menu. (Here

you set up the ATM network.)

 

 

 

2

Select the ATM CONFIG menu.

 

 

3

Enter the IDLE CELLS format for your network.

 

 

4

Set DATA SCRAMBLING appropriately for your network.

 

 

5

Back all the way out to the top level Total Access 600 menu, and then

select the ROUTER menu.

 

 

 

 

Enter the CONFIGURATION menu.

6

From this menu, you will set up addresses for your LAN and WAN.

 

For basic IP routing, use all the default values from the GLOBAL menu.

 

 

7

From the ETHERNET menu, enter the IP menu to enter your LAN

configuration.

 

 

 

 

Enter your LAN IP ADDRESS and SUBNET MASK.

8

For this example, the IP ADDRESS is 192.168.1.2 and the SUBNET MASK

 

is 255.255.255.0. This is not required, but will allow Telnet configuration

 

and TFTP upgrades from the LAN.

 

 

 

Arrow back to the main ROUTER CONFIGURATION menu, and select the

9

WAN menu and then the ATM menu. (Here you will enter your data

 

PVC information.)

 

 

10

Create a new PVC by entering the menu. Enter your VPI and VCI

values.

 

 

 

 

Disable IP on the RFC1483 IP menu and enable Bridging on the

11

RFC1483 BRIDGE menu. (This enables the Total Access 600 as a

 

bridge.)

 

 

 

Arrow back to the top level Total Access 600 menu to activate your

12

changes.

 

All packets that come in on the Ethernet will be forwarded on the WAN.

 

 

Total Access 600 Series User Manual

© 2002, ADTRAN, Inc.

Page 69 Page 71
Image 70
Page 69 Page 71
Contents Total Access 600 Series Shdsl IAD Trademarks To the Holder of the ManualSafety Instructions 2002, ADTRAN, Inc 2002, ADTRAN, Inc 2002, ADTRAN, Inc Warranty and Customer Service Limited Product WarrantyRepair and Return Customer Service, Product Support Information, and TrainingPre-Sales Inquiries and Applications Support Post-Sale Support Installation and Maintenance SupportTraining Total Access 600 Series Shdsl IAD User Interface Guide +@A1 +@&.&$$ +@,%.% @/& % @/& %.&$$ @.&$$ @/1 @.%+0% %B,% ##%B 8= $*+*$&,$&-# # #$% Figures Firmware Updates Analog LifelineVoice Over DSL Overview Voice over DSL System Info Serial Number Bootcode RevisionPart Number Firmware RevisionTelnet Access System ConfigNetwork Timing Mode Telnet User ListMaint Port Menu Password ProtectInstructions for Changing Passwords Step Action LevelNetwork Time Upgrade Firmware System UtilityConfig Transfer Ping Dslam Type Configuring WAN SettingsATM Config Layer One InterfaceATM Stats Data ScramblingAP Rx OAM Cells AP Receive Cell ErrorsAP Rx Cells AP Receive Cells DiscardedAAL5 No ATM Frames AAL5 Receive ErrorsAAL5 Receive Discarded Frames AAL5 No Data PacketsConfiguring the Router Configuration GlobalText string used to represent the domain name Bridge Security Dotted decimal format2002, ADTRAN, Inc Ethernet Ethernet MenuUse this menu to enable RIP on the LAN interface MAC AddressWAN This selection enables IP on this PVC RFC 1483 Bridge PPPoATMThis is the username used to authenticate the PPP peer Only routes not learned on the WAN connection This is the PPP encapsulation. LLC or VC-Mux Configuring the Router Status Router/Status MenuConfiguring the Router Logs Connection Log Sys log HostPPP Log Network LogConfiguring Voice Support Config Call ControlPVC Stats Configuring Voice Support StatusGateway Stats Pots StatsMenu Managing the Modules ModulesTest FXS Configuration Managing the Modules V.35 SetupMode Following settings are used for FRF5 Following settings are used for FRF8 Appendix A. Updating Total Access 600 Firmware using Xmodem Updating Firmware via a Forced DownloadPress $until a menu appears Updating Firmware via the Console Menus When prompted, press to erase flashSelect -# # for #9 Appendix B. Updating Total Access 600 Firmware using Tftp Message Meaning Message Meaning Menu Path Left Pane Status Bar ModeSystem Time Window Pane Navigation Right Window Pane NotationAdditional Terminal Menu Window Features Navigating Using the Keyboard KeysSession Management Keystrokes Getting Help Application Diagram Voice Turn Up Step Action Appendix E. RFC1483 Quick Start IP Routing IP Routing Step Action Appendix F. RFC1483 Quick Start IP Routing with NAT OptionsAppendix G. RFC1483 Quick Start Bridging Bridging Step ActionAppendix H. Craft Port Connection Pin-out 2002, ADTRAN, Inc
Top Page Image Contents