Ricoh 400780, Type B, AP2610 setup guide

Page 2

Introduction

This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine.

Please read “Safety Information” in this manual before using this machine. It contains important infor- mation related to USER SAFETY and PREVENTING EQUIPMENT PROBLEMS.

Power Source

120 V, 60 Hz, 8.4 A or more

Please be sure to connect the power cable to a power source as shown above.

Operator Safety:

This machine is considered a CDRH class I laser device, safe for office/EDP use. The machine con- tains 7 milliwatt, 645 - 660 nanometer wavelength, AlGaInp Laser Diode. Direct (or indirect reflected) eye contact with the laser beam might cause serious eye damage. Safety precautions and interlock mechanisms have been designed to prevent any possible laser beam exposure to the operator.

Laser Safety:

The Center for Devices and Radiological Health (CDRH) prohibits the repair of laser-based optical unit in the field. The optical housing unit can only be repaired in a factory or at a location with the requisite equipment. The laser subsystem is replaceable in the field by a qualified Customer Engineer. The laser chassis is not repairable in the field. Customer engineers are therefore directed to return all chassis and laser subsystems to the factory or service depot when replacement or the optical subsystem is re- quired.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be li- able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper- ating the machine.

Caution:

Use of controls or adjustment or performance of procedures other than those specified in this manual might result in hazardous radiation exposure.

Do not attempt any maintenance or troubleshooting other than that mentioned in this manual. This printer contains a laser beam generator and direct exposure to laser beams can cause permanent eye damage.

Two kinds of size notation are employed in this manual. With this machine refer to the inch version.

For good print quality, the supplier recommends that you use genuine toner from the supplier.

The supplier shall not be responsible for any damage or expense that might result from the use of parts other than genuine parts from the supplier with your office products.

Image 2
Contents Setup Guide Page Trademarks Safety Information Safety During OperationPositions of Labels and Hallmarks for Rwarning and Rcaution Page Energy Star Program SpecificationsEnergy Saver mode Manuals for This Printer Manuals for This PrinterPreparation How to Read This ManualSymbols LimitationTable of Contents Installing the Printer Driver Using USB Installing the Rpcs Printer DriverInstalling the PostScript Printer Driver Installing the Printer Driver Using IeeePage Time Saving Features of This PrinterMajor Specifications Compact BodyRpcs printer driver Printer Drivers for This PrinterPCL printer drivers Adobe PostScript Printer Drivers and PPD files Agfa Monotype Font Manager SmartNetMonitor for AdminSoftware and Utilities Included on the CD SmartNetMonitor for ClientViewing the Contents of the CD-ROM Exterior Guide to This PrinterMainframe Output Tray Standard Tray Front Cover Release Button Power CordPower Switch Upper CoverInterior Form Feed key Job Reset keyControl Panel Menu keyEscape key Enter # keyInstalling Options Option ListEnvelope Feeder Type Available OptionsPaper Feed Unit Type 2600 Tray 2 or Tray Basic model Printer Interior 802.11b Interface Unit Type a Memory Unit TypeB 64MB Network standard model Printer InteriorMemory Unit TypeB 64MB Hard Disk Drive Type Paper Feed Unit Type Attach the interface cable to the printerReference Envelope Feeder Type Pull out the handle of the control- ler board Memory Unit TypeB 64MBUse a coin to remove the two screws Pull the handle and slide the con- troller board outIf the Duplex Unit is not at- tached, go to step N Installing Options Installing the Network Interface Board Network Interface Board TypeFasten the Network Interface Board to the controller board If the Duplex Unit is not at- tached, go to step O Connecting the Network Interface Cable to the Network Turn off the power switch Loop the network interface cableInstalling the 1394 Interface Unit Interface Unit TypeAttach the 1394 Interface Unit to the controller board Fasten the 1394 Interface Unit to the controller board Required cable Connecting the 1394 InterfacePower supply Bus802.11b Interface Unit Type a Attach the 802.11b Interface Unit Ing the Configuration Hard Disk Drive Type Fasten the Hard Disk DrivePress Enter # to format the Hard Disk Drive Press On LineAD410 Duplex Unit Remove the rear cover in the hor- izontal directionAfter installing the last option that Bin Shift Sort Tray Type Remove the upper cover of the printerSlide the upper tray into the 1-bin Shift Sort Tray CS380 Mailbox CS380 Mailbox Installing Options Configuring the Printer for the Network Ethernet ConfigurationPress U or T to display Host Interface menu Press U or T to display Net- work SetupPress Menu Press Enter #Press U or T to display Network Boot If you use TCP/IP, assign the IP address to the printerPress U or T to display LAN Type If you use NetWare, select the frame type for NetWarePress U or T to display Frame Type NW Press U or T to display EthernetPress U or T to display IP over Ieee 1394 ConfigurationPress U or T to display Ieee 1394 Setup Press U or T to display Scsi print Assign the IP address to the printerPress U or T until the fol Lowing message appears Ready Ieee 802.11b Wireless LAN Configuration Press U or T to display Ieee 802.11bSubnet Mask Gateway AddressConfiguring the Printer for the Network Installing the Printer Driver and Software Installation MethodQuick Install Select Quick InstallClick Install Follow the instructions on the screenSelect PCL/RPCS Printer Drivers Installing the PCL 6/5e Printer DriverInstalling the PCL 6/5e Printer Driver Setting Up Options Installing the Rpcs Printer Driver Installing the Rpcs Printer DriverInstalling the Rpcs Printer Driver Installing the printer driver Installing the PostScript Printer DriverWindows 95/98/Me Installing the PostScript Printer Driver Click Next Check Local Printer and then click NextSetting up options Select PostScript 3 Printer Driver Add Printer Wizard startsClick the Device Settings tab Windows NT 4.0 Installing the PostScript Printer Driver When connecting with a parallel cable Bidirectional transmissionWhen connecting with USB When connecting with the networkWhen connecting with Ieee Macintosh Installing the PostScript 3 Printer Driver Setting up the PPD fileClick Configure Close the Chooser dialog boxCheck Specify a location, and then click Browse Installing the Printer Driver Using USBWindows 98/Me Installing the Printer Driver Using USB Click FinishClick Create Macintosh-Creating a Desktop Printer iconClick Change in USB Printer Selection Enter the printer name, and then click SaveInstalling the Printer Driver Using Ieee Printing with Scsi PrintClick Browse Click Open Click OKWindows XP Printing with IP over Inactivating the DeviceFound New Hardware Wizard dialog box, and then click Next Installing the SmartNetMonitor for Client/Admin Select SmartNetMonitor for Client/AdminInstalling the Agfa Monotype Font Manager Select Agfa Monotype Font ManagerUsing Adobe PageMaker Version 6.0 or Index Rpcs UE USA G074 Means Power ON. b means Power OFF UE USA G074-8637