Ricoh 400780, Type B, AP2610 setup guide If the Duplex Unit is not at- tached, go to step O

Page 35

Network Interface Board Type 2610

K Match the controller board to the top and bottom rail using the "T" mark, and then slide it into the printer slowly until it stops.

ZGDX253J

L Push back the handle of the con- troller board until it clicks.

N While aligning the power cord to the left side groove of the Duplex Unit, slide the Duplex Unit in un- til it is connected to the printer.

2

ZGDX241J

O Plug the printer's power cord back into the wall outlet, and then turn on the power switch.

ZGDX380J

M Fasten the controller board to the printer with the two screws.

ZGDX271J

Note

❒If the Duplex Unit is not at- tached, go to step O.

23

Image 35

Contents Setup Guide Page Trademarks Safety During Operation Safety InformationPositions of Labels and Hallmarks for Rwarning and Rcaution Page Energy Star Program SpecificationsEnergy Saver mode Manuals for This Printer Manuals for This PrinterLimitation How to Read This ManualSymbols PreparationTable of Contents Installing the Printer Driver Using Ieee Installing the Rpcs Printer DriverInstalling the PostScript Printer Driver Installing the Printer Driver Using USBPage Compact Body Features of This PrinterMajor Specifications Time SavingRpcs printer driver Printer Drivers for This PrinterPCL printer drivers Adobe PostScript Printer Drivers and PPD files SmartNetMonitor for Client SmartNetMonitor for AdminSoftware and Utilities Included on the CD Agfa Monotype Font ManagerViewing the Contents of the CD-ROM Exterior Guide to This PrinterMainframe Upper Cover Front Cover Release Button Power CordPower Switch Output Tray Standard TrayInterior Menu key Job Reset keyControl Panel Form Feed keyEnter # key Escape keyOption List Installing OptionsEnvelope Feeder Type Available OptionsPaper Feed Unit Type 2600 Tray 2 or Tray Basic model Printer Interior 802.11b Interface Unit Type a Memory Unit TypeB 64MB Network standard model Printer InteriorMemory Unit TypeB 64MB Hard Disk Drive Type Attach the interface cable to the printer Paper Feed Unit TypeReference Envelope Feeder Type Pull the handle and slide the con- troller board out Memory Unit TypeB 64MBUse a coin to remove the two screws Pull out the handle of the control- ler boardIf the Duplex Unit is not at- tached, go to step N Installing Options Network Interface Board Type Installing the Network Interface BoardFasten the Network Interface Board to the controller board If the Duplex Unit is not at- tached, go to step O Turn off the power switch Loop the network interface cable Connecting the Network Interface Cable to the NetworkInterface Unit Type Installing the 1394 Interface UnitAttach the 1394 Interface Unit to the controller board Fasten the 1394 Interface Unit to the controller board Bus Connecting the 1394 InterfacePower supply Required cable802.11b Interface Unit Type a Attach the 802.11b Interface Unit Ing the Configuration Fasten the Hard Disk Drive Hard Disk Drive TypePress On Line Press Enter # to format the Hard Disk DriveRemove the rear cover in the hor- izontal direction AD410 Duplex UnitAfter installing the last option that Remove the upper cover of the printer Bin Shift Sort Tray TypeSlide the upper tray into the 1-bin Shift Sort Tray CS380 Mailbox CS380 Mailbox Installing Options Ethernet Configuration Configuring the Printer for the NetworkPress Enter # Press U or T to display Net- work SetupPress Menu Press U or T to display Host Interface menuIf you use TCP/IP, assign the IP address to the printer Press U or T to display Network BootPress U or T to display Ethernet If you use NetWare, select the frame type for NetWarePress U or T to display Frame Type NW Press U or T to display LAN TypePress U or T to display IP over Ieee 1394 ConfigurationPress U or T to display Ieee 1394 Setup Press U or T to display Scsi print Assign the IP address to the printerPress U or T until the fol Lowing message appears Ready Press U or T to display Ieee 802.11b Ieee 802.11b Wireless LAN ConfigurationGateway Address Subnet MaskConfiguring the Printer for the Network Installation Method Installing the Printer Driver and SoftwareSelect Quick Install Quick InstallFollow the instructions on the screen Click InstallSelect PCL/RPCS Printer Drivers Installing the PCL 6/5e Printer DriverInstalling the PCL 6/5e Printer Driver Setting Up Options Installing the Rpcs Printer Driver Installing the Rpcs Printer DriverInstalling the Rpcs Printer Driver Click Next Check Local Printer and then click Next Installing the PostScript Printer DriverWindows 95/98/Me Installing the PostScript Printer Driver Installing the printer driverSelect PostScript 3 Printer Driver Add Printer Wizard starts Setting up optionsClick the Device Settings tab Windows NT 4.0 Installing the PostScript Printer Driver Bidirectional transmission When connecting with a parallel cableWhen connecting with USB When connecting with the networkWhen connecting with Ieee Setting up the PPD file Macintosh Installing the PostScript 3 Printer DriverClose the Chooser dialog box Click ConfigureClick Finish Installing the Printer Driver Using USBWindows 98/Me Installing the Printer Driver Using USB Check Specify a location, and then click BrowseEnter the printer name, and then click Save Macintosh-Creating a Desktop Printer iconClick Change in USB Printer Selection Click CreatePrinting with Scsi Print Installing the Printer Driver Using IeeeClick Open Click OK Click BrowseWindows XP Inactivating the Device Printing with IP overFound New Hardware Wizard dialog box, and then click Next Select SmartNetMonitor for Client/Admin Installing the SmartNetMonitor for Client/AdminSelect Agfa Monotype Font Manager Installing the Agfa Monotype Font ManagerUsing Adobe PageMaker Version 6.0 or Index Rpcs UE USA G074 Means Power ON. b means Power OFF UE USA G074-8637