Ricoh 400780, Type B, AP2610 setup guide Interior

Page 20

Getting Started

❖Interior

		[Front side]	[Back side]
	1

1.Toner Cartridge

Includes toner and a photoconductor unit.

When “Replace Toner Cartridge” ap- pears on the panel display, replace this unit.

2.Front Cover

Open this cover when accessing the inside of the printer.

3.Guide Board

Open this board to remove misfed pa- per.

ZGDH230J

5.Transfer Roller Cover

Open this cover when replacing a transfer roller.

6.Transfer Roller

When “Replace Maintenance Kit” ap- pears on the panel display, replace this roller.

7.Fusing Unit Lock Levers

Lift these levers when replacing the fusing unit.

8.Fusing Unit

Fuses the image onto paper.

4.Registration Roller

Feeds the paper. If it becomes dirty, clean it.

See “Cleaning the Registration Roller” in the Printer Reference on the CD-ROM labeled "Operating Instructions".

When “Replace Maintenance Kit” ap- pears on the panel display, replace this unit.

8

Image 20

Contents Setup Guide Page Trademarks Safety Information Safety During OperationPositions of Labels and Hallmarks for Rwarning and Rcaution Page Energy Star Program SpecificationsEnergy Saver mode Manuals for This Printer Manuals for This PrinterHow to Read This Manual SymbolsPreparation LimitationTable of Contents Installing the Rpcs Printer Driver Installing the PostScript Printer DriverInstalling the Printer Driver Using USB Installing the Printer Driver Using IeeePage Features of This Printer Major SpecificationsTime Saving Compact BodyRpcs printer driver Printer Drivers for This PrinterPCL printer drivers Adobe PostScript Printer Drivers and PPD files SmartNetMonitor for Admin Software and Utilities Included on the CDAgfa Monotype Font Manager SmartNetMonitor for Client Viewing the Contents of the CD-ROM Exterior Guide to This PrinterMainframe Front Cover Release Button Power Cord Power SwitchOutput Tray Standard Tray Upper CoverInterior Job Reset key Control PanelForm Feed key Menu keyEscape key Enter # keyInstalling Options Option ListEnvelope Feeder Type Available OptionsPaper Feed Unit Type 2600 Tray 2 or Tray Basic model Printer Interior 802.11b Interface Unit Type a Memory Unit TypeB 64MB Network standard model Printer InteriorMemory Unit TypeB 64MB Hard Disk Drive Type Paper Feed Unit Type Attach the interface cable to the printerReference Envelope Feeder Type Memory Unit TypeB 64MB Use a coin to remove the two screwsPull out the handle of the control- ler board Pull the handle and slide the con- troller board outIf the Duplex Unit is not at- tached, go to step N Installing Options Installing the Network Interface Board Network Interface Board TypeFasten the Network Interface Board to the controller board If the Duplex Unit is not at- tached, go to step O Connecting the Network Interface Cable to the Network Turn off the power switch Loop the network interface cableInstalling the 1394 Interface Unit Interface Unit TypeAttach the 1394 Interface Unit to the controller board Fasten the 1394 Interface Unit to the controller board Connecting the 1394 Interface Power supplyRequired cable Bus802.11b Interface Unit Type a Attach the 802.11b Interface Unit Ing the Configuration Hard Disk Drive Type Fasten the Hard Disk DrivePress Enter # to format the Hard Disk Drive Press On LineAD410 Duplex Unit Remove the rear cover in the hor- izontal directionAfter installing the last option that Bin Shift Sort Tray Type Remove the upper cover of the printerSlide the upper tray into the 1-bin Shift Sort Tray CS380 Mailbox CS380 Mailbox Installing Options Configuring the Printer for the Network Ethernet ConfigurationPress U or T to display Net- work Setup Press MenuPress U or T to display Host Interface menu Press Enter #Press U or T to display Network Boot If you use TCP/IP, assign the IP address to the printerIf you use NetWare, select the frame type for NetWare Press U or T to display Frame Type NWPress U or T to display LAN Type Press U or T to display EthernetPress U or T to display IP over Ieee 1394 ConfigurationPress U or T to display Ieee 1394 Setup Press U or T to display Scsi print Assign the IP address to the printerPress U or T until the fol Lowing message appears Ready Ieee 802.11b Wireless LAN Configuration Press U or T to display Ieee 802.11bSubnet Mask Gateway AddressConfiguring the Printer for the Network Installing the Printer Driver and Software Installation MethodQuick Install Select Quick InstallClick Install Follow the instructions on the screenSelect PCL/RPCS Printer Drivers Installing the PCL 6/5e Printer DriverInstalling the PCL 6/5e Printer Driver Setting Up Options Installing the Rpcs Printer Driver Installing the Rpcs Printer DriverInstalling the Rpcs Printer Driver Installing the PostScript Printer Driver Windows 95/98/Me Installing the PostScript Printer DriverInstalling the printer driver Click Next Check Local Printer and then click NextSetting up options Select PostScript 3 Printer Driver Add Printer Wizard startsClick the Device Settings tab Windows NT 4.0 Installing the PostScript Printer Driver When connecting with a parallel cable Bidirectional transmissionWhen connecting with USB When connecting with the networkWhen connecting with Ieee Macintosh Installing the PostScript 3 Printer Driver Setting up the PPD fileClick Configure Close the Chooser dialog boxInstalling the Printer Driver Using USB Windows 98/Me Installing the Printer Driver Using USBCheck Specify a location, and then click Browse Click FinishMacintosh-Creating a Desktop Printer icon Click Change in USB Printer SelectionClick Create Enter the printer name, and then click SaveInstalling the Printer Driver Using Ieee Printing with Scsi PrintClick Browse Click Open Click OKWindows XP Printing with IP over Inactivating the DeviceFound New Hardware Wizard dialog box, and then click Next Installing the SmartNetMonitor for Client/Admin Select SmartNetMonitor for Client/AdminInstalling the Agfa Monotype Font Manager Select Agfa Monotype Font ManagerUsing Adobe PageMaker Version 6.0 or Index Rpcs UE USA G074 Means Power ON. b means Power OFF UE USA G074-8637