Ricoh Type B, AP2610, 400780 setup guide Connecting the Network Interface Cable to the Network

Page 36

Installing Options

Connecting the Network Interface Cable to the Network

A Turn off the power switch.

B Loop the network interface cable

2	and attach the ferrite core.

Note

❒The network interface cable loop should be about 15 cm (6") (A) from the end of the cable (on the end closet to the print- er). The ferrite core at the end of the cable should be a ring type ferrite core.

ZDDP320E

C Attach the network interface ca- ble to the jack on the Network In- terface Unit.

ZGDX291J

D Connect the other end of the net- work interface cable to the net- work.

E Turn on the power switch.

Note

❒After installing the last option that you want, print the configuration page to confirm the installation. If the information about network set- tings (e.g. IP address) is listed in the configuration page, then it has been properly installed. For more information about printing the configuration page, see "Printing the Configuration Page" in the Printer Reference on the CD-ROM labeled "Operating Instructions".

24

Image 36

Contents Setup Guide Page Trademarks Safety Information Safety During OperationPositions of Labels and Hallmarks for Rwarning and Rcaution Page Specifications Energy Saver modeEnergy Star Program Manuals for This Printer Manuals for This PrinterHow to Read This Manual SymbolsPreparation LimitationTable of Contents Installing the Rpcs Printer Driver Installing the PostScript Printer DriverInstalling the Printer Driver Using USB Installing the Printer Driver Using IeeePage Features of This Printer Major SpecificationsTime Saving Compact BodyPrinter Drivers for This Printer PCL printer driversRpcs printer driver Adobe PostScript Printer Drivers and PPD files SmartNetMonitor for Admin Software and Utilities Included on the CDAgfa Monotype Font Manager SmartNetMonitor for ClientViewing the Contents of the CD-ROM Guide to This Printer MainframeExterior Front Cover Release Button Power Cord Power SwitchOutput Tray Standard Tray Upper CoverInterior Job Reset key Control PanelForm Feed key Menu keyEscape key Enter # keyInstalling Options Option ListAvailable Options Paper Feed Unit Type 2600 Tray 2 or TrayEnvelope Feeder Type Basic model Printer Interior Network standard model Printer Interior Memory Unit TypeB 64MB Hard Disk Drive Type802.11b Interface Unit Type a Memory Unit TypeB 64MB Paper Feed Unit Type Attach the interface cable to the printerReference Envelope Feeder Type Memory Unit TypeB 64MB Use a coin to remove the two screwsPull out the handle of the control- ler board Pull the handle and slide the con- troller board outIf the Duplex Unit is not at- tached, go to step N Installing Options Installing the Network Interface Board Network Interface Board TypeFasten the Network Interface Board to the controller board If the Duplex Unit is not at- tached, go to step O Connecting the Network Interface Cable to the Network Turn off the power switch Loop the network interface cableInstalling the 1394 Interface Unit Interface Unit TypeAttach the 1394 Interface Unit to the controller board Fasten the 1394 Interface Unit to the controller board Connecting the 1394 Interface Power supplyRequired cable Bus802.11b Interface Unit Type a Attach the 802.11b Interface Unit Ing the Configuration Hard Disk Drive Type Fasten the Hard Disk DrivePress Enter # to format the Hard Disk Drive Press On LineAD410 Duplex Unit Remove the rear cover in the hor- izontal directionAfter installing the last option that Bin Shift Sort Tray Type Remove the upper cover of the printerSlide the upper tray into the 1-bin Shift Sort Tray CS380 Mailbox CS380 Mailbox Installing Options Configuring the Printer for the Network Ethernet ConfigurationPress U or T to display Net- work Setup Press MenuPress U or T to display Host Interface menu Press Enter #Press U or T to display Network Boot If you use TCP/IP, assign the IP address to the printerIf you use NetWare, select the frame type for NetWare Press U or T to display Frame Type NWPress U or T to display LAN Type Press U or T to display EthernetIeee 1394 Configuration Press U or T to display Ieee 1394 SetupPress U or T to display IP over Assign the IP address to the printer Press U or T until the fol Lowing message appearsPress U or T to display Scsi print Ready Ieee 802.11b Wireless LAN Configuration Press U or T to display Ieee 802.11bSubnet Mask Gateway AddressConfiguring the Printer for the Network Installing the Printer Driver and Software Installation MethodQuick Install Select Quick InstallClick Install Follow the instructions on the screenInstalling the PCL 6/5e Printer Driver Installing the PCL 6/5e Printer DriverSelect PCL/RPCS Printer Drivers Setting Up Options Installing the Rpcs Printer Driver Installing the Rpcs Printer DriverInstalling the Rpcs Printer Driver Installing the PostScript Printer Driver Windows 95/98/Me Installing the PostScript Printer DriverInstalling the printer driver Click Next Check Local Printer and then click NextSetting up options Select PostScript 3 Printer Driver Add Printer Wizard startsClick the Device Settings tab Windows NT 4.0 Installing the PostScript Printer Driver When connecting with a parallel cable Bidirectional transmissionWhen connecting with the network When connecting with IeeeWhen connecting with USB Macintosh Installing the PostScript 3 Printer Driver Setting up the PPD fileClick Configure Close the Chooser dialog boxInstalling the Printer Driver Using USB Windows 98/Me Installing the Printer Driver Using USBCheck Specify a location, and then click Browse Click FinishMacintosh-Creating a Desktop Printer icon Click Change in USB Printer SelectionClick Create Enter the printer name, and then click SaveInstalling the Printer Driver Using Ieee Printing with Scsi PrintClick Browse Click Open Click OKWindows XP Printing with IP over Inactivating the DeviceFound New Hardware Wizard dialog box, and then click Next Installing the SmartNetMonitor for Client/Admin Select SmartNetMonitor for Client/AdminInstalling the Agfa Monotype Font Manager Select Agfa Monotype Font ManagerUsing Adobe PageMaker Version 6.0 or Index Rpcs UE USA G074 Means Power ON. b means Power OFF UE USA G074-8637