Ricoh AP2610, Type B, 400780 setup guide Pull out the handle of the control- ler board

Page 34

Installing Options

E Pull out the handle of the control- ler board.

2

ZGDX370J

F Pull the handle and slide the con- troller board out.

ZGDX261J

G Place the controller board on a flat surface.

H Use a coin to remove the two screws, and then remove the cover.

Note

❒These screws are used again in step J.

❒The removed cover is not used when installing the Network In- terface Board.

22

ZGDX410J

I Insert the end of the Network In- terface Board into the opening (A), and then push down until it clicks (B).

ZGDX422J

ZGDX432J

J Fasten the Network Interface Board to the controller board.

ZGDX441J

Image 34

Contents Setup Guide Page Trademarks Safety Information Safety During OperationPositions of Labels and Hallmarks for Rwarning and Rcaution Page Energy Saver mode SpecificationsEnergy Star Program Manuals for This Printer Manuals for This PrinterPreparation How to Read This ManualSymbols LimitationTable of Contents Installing the Printer Driver Using USB Installing the Rpcs Printer DriverInstalling the PostScript Printer Driver Installing the Printer Driver Using IeeePage Time Saving Features of This PrinterMajor Specifications Compact BodyPCL printer drivers Printer Drivers for This PrinterRpcs printer driver Adobe PostScript Printer Drivers and PPD files Agfa Monotype Font Manager SmartNetMonitor for AdminSoftware and Utilities Included on the CD SmartNetMonitor for ClientViewing the Contents of the CD-ROM Mainframe Guide to This PrinterExterior Output Tray Standard Tray Front Cover Release Button Power CordPower Switch Upper CoverInterior Form Feed key Job Reset keyControl Panel Menu keyEscape key Enter # keyInstalling Options Option ListPaper Feed Unit Type 2600 Tray 2 or Tray Available OptionsEnvelope Feeder Type Basic model Printer Interior Memory Unit TypeB 64MB Hard Disk Drive Type Network standard model Printer Interior802.11b Interface Unit Type a Memory Unit TypeB 64MB Paper Feed Unit Type Attach the interface cable to the printerReference Envelope Feeder Type Pull out the handle of the control- ler board Memory Unit TypeB 64MBUse a coin to remove the two screws Pull the handle and slide the con- troller board out If the Duplex Unit is not at- tached, go to step N Installing Options Installing the Network Interface Board Network Interface Board TypeFasten the Network Interface Board to the controller board If the Duplex Unit is not at- tached, go to step O Connecting the Network Interface Cable to the Network Turn off the power switch Loop the network interface cableInstalling the 1394 Interface Unit Interface Unit TypeAttach the 1394 Interface Unit to the controller board Fasten the 1394 Interface Unit to the controller board Required cable Connecting the 1394 InterfacePower supply Bus802.11b Interface Unit Type a Attach the 802.11b Interface Unit Ing the Configuration Hard Disk Drive Type Fasten the Hard Disk DrivePress Enter # to format the Hard Disk Drive Press On LineAD410 Duplex Unit Remove the rear cover in the hor- izontal directionAfter installing the last option that Bin Shift Sort Tray Type Remove the upper cover of the printerSlide the upper tray into the 1-bin Shift Sort Tray CS380 Mailbox CS380 Mailbox Installing Options Configuring the Printer for the Network Ethernet ConfigurationPress U or T to display Host Interface menu Press U or T to display Net- work SetupPress Menu Press Enter #Press U or T to display Network Boot If you use TCP/IP, assign the IP address to the printerPress U or T to display LAN Type If you use NetWare, select the frame type for NetWarePress U or T to display Frame Type NW Press U or T to display EthernetPress U or T to display Ieee 1394 Setup Ieee 1394 ConfigurationPress U or T to display IP over Press U or T until the fol Lowing message appears Assign the IP address to the printerPress U or T to display Scsi print Ready Ieee 802.11b Wireless LAN Configuration Press U or T to display Ieee 802.11bSubnet Mask Gateway AddressConfiguring the Printer for the Network Installing the Printer Driver and Software Installation MethodQuick Install Select Quick InstallClick Install Follow the instructions on the screenInstalling the PCL 6/5e Printer Driver Installing the PCL 6/5e Printer DriverSelect PCL/RPCS Printer Drivers Setting Up Options Installing the Rpcs Printer Driver Installing the Rpcs Printer DriverInstalling the Rpcs Printer Driver Installing the printer driver Installing the PostScript Printer DriverWindows 95/98/Me Installing the PostScript Printer Driver Click Next Check Local Printer and then click NextSetting up options Select PostScript 3 Printer Driver Add Printer Wizard startsClick the Device Settings tab Windows NT 4.0 Installing the PostScript Printer Driver When connecting with a parallel cable Bidirectional transmissionWhen connecting with Ieee When connecting with the networkWhen connecting with USB Macintosh Installing the PostScript 3 Printer Driver Setting up the PPD fileClick Configure Close the Chooser dialog boxCheck Specify a location, and then click Browse Installing the Printer Driver Using USBWindows 98/Me Installing the Printer Driver Using USB Click FinishClick Create Macintosh-Creating a Desktop Printer iconClick Change in USB Printer Selection Enter the printer name, and then click SaveInstalling the Printer Driver Using Ieee Printing with Scsi PrintClick Browse Click Open Click OKWindows XP Printing with IP over Inactivating the DeviceFound New Hardware Wizard dialog box, and then click Next Installing the SmartNetMonitor for Client/Admin Select SmartNetMonitor for Client/AdminInstalling the Agfa Monotype Font Manager Select Agfa Monotype Font ManagerUsing Adobe PageMaker Version 6.0 or Index Rpcs UE USA G074 Means Power ON. b means Power OFF UE USA G074-8637