Ricoh
Type B, AP2610, 400780
setup guide
Specification
Install
Symbols
SmartNetMonitor for Admin
Connecting the 1394 Interface
Ing the Configuration
Job Reset key
Setup Guide
Click the Device Settings tab
Safety
Page 6
A
B
iv
Page 5
Page 7
Image 6
Page 5
Page 7
Contents
Setup Guide
Page
Trademarks
Safety Information
Safety During Operation
Positions of Labels and Hallmarks for Rwarning and Rcaution
Page
Specifications
Energy Saver mode
Energy Star Program
Manuals for This Printer
Manuals for This Printer
Preparation
How to Read This Manual
Symbols
Limitation
Table of Contents
Installing the Printer Driver Using USB
Installing the Rpcs Printer Driver
Installing the PostScript Printer Driver
Installing the Printer Driver Using Ieee
Page
Time Saving
Features of This Printer
Major Specifications
Compact Body
Printer Drivers for This Printer
PCL printer drivers
Rpcs printer driver
Adobe PostScript Printer Drivers and PPD files
Agfa Monotype Font Manager
SmartNetMonitor for Admin
Software and Utilities Included on the CD
SmartNetMonitor for Client
Viewing the Contents of the CD-ROM
Guide to This Printer
Mainframe
Exterior
Output Tray Standard Tray
Front Cover Release Button Power Cord
Power Switch
Upper Cover
Interior
Form Feed key
Job Reset key
Control Panel
Menu key
Escape key
Enter # key
Installing Options
Option List
Available Options
Paper Feed Unit Type 2600 Tray 2 or Tray
Envelope Feeder Type
Basic model Printer Interior
Network standard model Printer Interior
Memory Unit TypeB 64MB Hard Disk Drive Type
802.11b Interface Unit Type a Memory Unit TypeB 64MB
Paper Feed Unit Type
Attach the interface cable to the printer
Reference
Envelope Feeder Type
Pull out the handle of the control- ler board
Memory Unit TypeB 64MB
Use a coin to remove the two screws
Pull the handle and slide the con- troller board out
If the Duplex Unit is not at- tached, go to step N
Installing Options
Installing the Network Interface Board
Network Interface Board Type
Fasten the Network Interface Board to the controller board
If the Duplex Unit is not at- tached, go to step O
Connecting the Network Interface Cable to the Network
Turn off the power switch Loop the network interface cable
Installing the 1394 Interface Unit
Interface Unit Type
Attach the 1394 Interface Unit to the controller board
Fasten the 1394 Interface Unit to the controller board
Required cable
Connecting the 1394 Interface
Power supply
Bus
802.11b Interface Unit Type a
Attach the 802.11b Interface Unit
Ing the Configuration
Hard Disk Drive Type
Fasten the Hard Disk Drive
Press Enter # to format the Hard Disk Drive
Press On Line
AD410 Duplex Unit
Remove the rear cover in the hor- izontal direction
After installing the last option that
Bin Shift Sort Tray Type
Remove the upper cover of the printer
Slide the upper tray into the 1-bin Shift Sort Tray
CS380 Mailbox
CS380 Mailbox
Installing Options
Configuring the Printer for the Network
Ethernet Configuration
Press U or T to display Host Interface menu
Press U or T to display Net- work Setup
Press Menu
Press Enter #
Press U or T to display Network Boot
If you use TCP/IP, assign the IP address to the printer
Press U or T to display LAN Type
If you use NetWare, select the frame type for NetWare
Press U or T to display Frame Type NW
Press U or T to display Ethernet
Ieee 1394 Configuration
Press U or T to display Ieee 1394 Setup
Press U or T to display IP over
Assign the IP address to the printer
Press U or T until the fol Lowing message appears
Press U or T to display Scsi print
Ready
Ieee 802.11b Wireless LAN Configuration
Press U or T to display Ieee 802.11b
Subnet Mask
Gateway Address
Configuring the Printer for the Network
Installing the Printer Driver and Software
Installation Method
Quick Install
Select Quick Install
Click Install
Follow the instructions on the screen
Installing the PCL 6/5e Printer Driver
Installing the PCL 6/5e Printer Driver
Select PCL/RPCS Printer Drivers
Setting Up Options
Installing the Rpcs Printer Driver
Installing the Rpcs Printer Driver
Installing the Rpcs Printer Driver
Installing the printer driver
Installing the PostScript Printer Driver
Windows 95/98/Me Installing the PostScript Printer Driver
Click Next Check Local Printer and then click Next
Setting up options
Select PostScript 3 Printer Driver Add Printer Wizard starts
Click the Device Settings tab
Windows NT 4.0 Installing the PostScript Printer Driver
When connecting with a parallel cable
Bidirectional transmission
When connecting with the network
When connecting with Ieee
When connecting with USB
Macintosh Installing the PostScript 3 Printer Driver
Setting up the PPD file
Click Configure
Close the Chooser dialog box
Check Specify a location, and then click Browse
Installing the Printer Driver Using USB
Windows 98/Me Installing the Printer Driver Using USB
Click Finish
Click Create
Macintosh-Creating a Desktop Printer icon
Click Change in USB Printer Selection
Enter the printer name, and then click Save
Installing the Printer Driver Using Ieee
Printing with Scsi Print
Click Browse
Click Open Click OK
Windows XP
Printing with IP over
Inactivating the Device
Found New Hardware Wizard dialog box, and then click Next
Installing the SmartNetMonitor for Client/Admin
Select SmartNetMonitor for Client/Admin
Installing the Agfa Monotype Font Manager
Select Agfa Monotype Font Manager
Using Adobe PageMaker Version 6.0 or
Index
Rpcs
UE USA G074
Means Power ON. b means Power OFF
UE USA G074-8637
Top
Page
Image
Contents