Ricoh Facsimile Reference Basic manual Placing Originals in the ADF

Page 22

Faxing

ˆMake sure that all ink, correcting fluid etc., has completely dried be- fore placing your original. If it is still wet, the exposure glass will be marked and those marks will ap- pear on the received image.

ˆYou can send the first pages from

2

the exposure glass then the re-

maining pages from the ADF. Af-

ter you have removed the last page from the exposure glass, insert the remaining pages in the ADF, and then press the {Start}key.

Reference

For acceptable types of originals, see p.107 “Acceptable Types of Originals”, Facsimile Reference <Ad- vanced Features> .

Placing a Single Original on the Exposure Glass

Place originals that cannot be placed in the ADF (Auto Document Feeder), such as a book, on the exposure glass one page at a time.

A Place the original face down and align its upper left corner with the reference mark at the upper left corner of the exposure glass.

ABZ025S.eps

ABZ025S

1.Positioning mark

2.Left Scale

B Lower the exposure glass cover or the ADF.

Note

ˆWhen setting a bound original, the received image may contain some black areas. To reduce this effect, hold down the original to prevent the bound part from rising.

Placing Originals in the ADF

Use the ADF to scan in a stack of orig- inals in one operation.

Limitation

ˆPlace all the originals to be sent in a single stack. You cannot place originals in the ADF one page at a time or in successive stacks.

Note

ˆTo send an original longer than the following lengths, use Memory Transmission. However, the maxi- mum length of an original for Memory Transmission is 1200 mm (47").

A4 size: 600 mm (23.6") for De- tail, 300 mm (11.8") for Fine

ˆIf you frequently send long docu- ments, set Long Document Trans- mission to on with the User Parameters. If a jam occurs, the document might be damaged be- cause scanning will not stop. See p.76 “User Parameters”, Facsimile Reference <Advanced Features> (switch 14, bit 1).

ˆIf your original is bent or folded, flatten it before you place it.

ˆWhen sending thin originals, place them on the exposure glass.

ˆIf an original jammed, press the {Clear/Stop} key, and then slowly remove the original.

14

Image 22
Contents Facsimile Reference Basic Features Operating Instructions Facsimile Reference Basic Features Introduction ™ FCC Requirements CanadaManuals for This Machine ™ Manuals for ScanRouter V2 Lite ™ Manuals for DeskTopBinder V2 Lite™ Other manuals Table of Contents Adjusting the Volume Canceling Internet Fax TransmissionInitial Settings and Adjustments When Toner Runs OutPage Remarque concernant les utilisateurs au Canada Important Safety Instructions Importantes Mesures DE SÉ- CuritéPreparation How to Read This ManualSymbols LimitationControl Panel ™ Features Programmed by Default Reading the display and using keys Reading the DisplayMachine status or currently se- lected function Message ™ When Internet Fax Settings is onStandby display Destination entry Selection keys Selectable items™ Memory Transmission fax transmission ™ TX ModeCommunication display ™ ReceptionUser code entry display Transmission Modes ™ Memory TransmissionFaxing Placing Originals 81/2Placing Originals in the ADF Placing a Single Original on the Exposure GlassOriginals unsuitable for the ADF Limit mark Document guideMemory Transmission Make sure the Memory Trans. in- dicator lightsPlace the original in the ADF, or on the exposure glass Make the settings you requireSpecify a destination Sending originals using the exposure glass Press the StartkeyPress the Clear Modeskey Canceling a Memory TransmissionWhile the Original Is Being Scanned Press the Clear/StopkeyPress Stop TX Make sure that the standby dis- play appearsPress Delete Make sure the Memory Trans. in- dicator is off Immediate TransmissionPlace the original Select the scan settings you re- quire FAX616.tif After You Have Pressed StartKey Canceling an Immediate TransmissionBefore You Have Pressed StartKey Press the Clear/Stop key, and then remove the originalScan Settings Resolution™ Photo Original Type™ Text Press the Original Type key for the type you requireWhen placing originals on the exposure glass Image Density ContrastWhen placing originals in the ADF ™ Fax number Specifying a DestinationEntering a Fax Number ™ E-mail addressPress the On Hook Dialkey PauseTone Press ToneEntering an E-mail Address Using the Destination ListPress Manual Specifying a destination using the Quick Dial key Specifying a group of destinations using the Quick Dial keyMake sure the destination name appears on the display Press the OK key when confir- mation is completePress the Check Destinationkey ™ Search by Destination Name Searching for a DestinationSearch by Destination Name ™ Search by Fax NumberSelecting from Destination List Select the destination name to specify using Uor TSelect the destination you want to specify using Tor U Select Display Destination List usSelect Search by Registration No. using Uor T Specifying a Registration NumberPress to display . Note2 Search by Fax NumberEnter a fax number to search for Search by Fax No. confirmationˆ If Search by E-mail Address does Search by E-mail AddressSearch by E-mail Address entry dis Select the e-mail address to speci- fy using Uor T Reception Switching the Reception Mode™ Auto Switch ™ Manual ReceptionReceiving a Fax in Manual Reception Mode Faxing Using Internet Fax Functions Internet Fax FunctionsFunctions Not Supported by E-mail Transmission Internet Fax PrecautionsFunctions Not Supported by E-mail Reception ™ Returning a Return Receipt Full Mode™ Registering the Received Reception Confirmation Contents ™ Requesting a Reception ConfirmationUsing Internet Fax Functions ™ Attach Subject Transmitting Internet Fax™ Return Receipt Key When you set an e-mail option, press TX ModeSelect Manual Input using U or T, and then press the OK key Enter the subjectPress Uor Tto select On Press the OKkey After selecting the subject, press the OKkeyEnter the e-mail address Specify the next destinationAbout the E-mail Subject Confirming Reception Canceling Internet Fax Transmission Manual E-mail Reception Receiving Internet FaxAuto E-mail Reception Press the programmed User FuncMail is in the server Press ExitDate Received ImagesSubject Message is inserted in all e- mails™ Own Name Initial Settings and Adjustments™ Fax Header ™ Own Fax Number facsimile number of senderProgramming Press the User Tools/CounterkeyEnter an Own Name, and then press the OKkey EditingPress the User Tools/Counter key Select Fax Header using U or T, and then press the OKkey DeletingDisplay returns to that of step E Programming Fax Numbers and E-mail addresses Adjusting the Volume You can adjust the volume using When Facsimile Key Is Lit in Red Problem SolutionsMake sure that the machine is in facsimile mode When Toner Runs OutPress Exit, and then perform transmission operation Error Messages and Their Meanings Cancelled14-09 Out of paper display message Solving Problems This table lists some common problems and their solutionsExceeded max. E When Things Dont Go as Expected Want Operation ReferenceIndex Auto Reception Manual Reception Memo EN USA B168-8607