Mitsubishi Electronics WD-60C8 manual Open the Inputs AV Receiver menu

Page 60

60

6. NetCommand IR Control (736 and 835 Series TVs)

Setting Up NetCommand Control of an A/V Receiver, continued

Before You Begin

1.Connect your A/V devices to the TV and connect your A/V receiver to the audio outputs on the TV and the DVD player. See chapter 3, “TV Connec- tions,” for suggestions. Important: To use Setup 1, you must connect the A/V receiver to the TV’s audio output; i.e., the TV’s AVR AUDIO OUTPUT or DIGITAL AUDIO OUTPUT jack.

2.Position NetCommand IR emitters as described in “IR Emitter Placement,” page 53.

3.Open the Inputs > AV Receiver menu.

Note: The terms Input1Input5used in the AV Re- ceiver menu are arbitrary names used by the TV to uniquely identify A/V receiver inputs.

A

2

4

3

AV Receiver menu to set up audio switching

AThe Learn column lists “learnable” input keys on the A/V receiver’s remote control.

BA check mark next to a key name indicates it has been “learned” by NetCommand.

CInput1 through Input5 are arbitrary names the TV uses to uniquely identify A/V receiver inputs.

DAfter “learning” IR codes for A/V receiver inputs, use the Assign Input column to identify the device connected to the TV and the associated A/V receiver input.

For the given example:

1.Connect the TV’s audio output to the A/V receiver’s TV audio input.

2.Using this screen, “learn” the IR code for the A/V receiver’s TV audio input as Input1 (item 3 above).

3.In the Assign Input1 column (item 4 above), assign the name TV Audio (the default) to the A/V receiver IR code previously learned as Input1.

4.Connect the DVD player’s audio output to the A/V receiver’s DVD input.

5.Using this screen, “learn” the IR code for the A/V receiver’s DVD audio input as Input2.

6.In the Assign Input2 column, assign the name DVD to the A/V receiver IR code previously learned as Input2 in this screen.

Audio Switching Setup 1: Automatic A/V Receiver Switching to the TV Audio Input

Most devices are set up to use the TV’s audio output like the VCR in this example; analog audio from the device is sent through the TV to the A/V receiver’s TV audio input.

Use this setup for:

Sources providing only analog stereo output, such as a VCR.

Audio from ANT 1 and ANT 2

1.Under Learn, highlight Input1.

In this example, the IR code for the A/V receiver’s TV Audio input will be “learned” as Input 1.

2.Press ENTER on the TV’s remote control.

3.While the text Input1 is flashing, press and hold the TV INPUT key on the A/V receiver’s remote control.

4.When a check appears next to Input 1, release the TV INPUT key.

If the text stops flashing before the check mark appears, repeat this step.

To erase the IR code just “learned,” press CANCEL while the name is highlighted.

5.Press once to highlight TV Audio (TV audio output) in the Assign Input1 column. The triangular marker is always next to the assigned sound source.

6.Press EXIT if finished or continue with setup for another TV audio source.

Completed NetCommand setup described for controlling A/V receiver switching to the A/V receiver’s audio input from the TV’s AUDIO OUTPUT.

IMPORTANT

All audio from what you are watching on the TV is always available from both the TV’s AVR AUDIO OUTPUT and DIGITAL AUDIO OUTPUT jacks.

To use the digital surround sound capabilities of your A/V receiver however, you must connect your DVD player, satellite receiver, or cable box directly to the A/V receiver, as surround sound may not be available from the TV’s audio output.

Image 60
Contents WD-60C8, WD-65C8, WD-73C8 WD-60735, WD-65735, WD-73735WD-65736, WD-73736 WD-65835, WD-73835Refer Servicing to Qualified Service Personnel For Your RecordsContents Installation Notes Lamp ReplacementCleaning Recommendations Internal FansReplacement Parts Outdoor Antenna GroundingPackage Contents Special Features of Your TVTV Front Panel Control PanelFront Inputs Front-Panel Indicators POWER/TIMER IndicatorStatus Indicator Lamp IndicatorTV Back Panel ANT 1/ANT 2 AntennaComposite Video Input 1, Input Component Video Input 1, InputIR NetCommand Output/External Controller Input Hdmi Inputs High-Definition Multimedia InterfaceAudio L and R Input 1, Input Hdmi Cable CategoriesGuidelines for Setting Up and Using Your New Widescreen TV When You First Power On the TVInstalling the Remote Control Batteries Additional TV Setup TV OperationTV Care AssistanceInitial TV Setup Setting Up TV InputsWhen You First Connect a Device Memorizing ChannelsSetup Procedure Setup Procedure for TV Inputs Disconnecting an Analog A/V ReceiverAuto Input/Auto Output Sensing Screens Tips on Auto Sensing and Changing Connected DevicesControlling A/V Receiver Sound Volume With a Standard TV SetupWith NetCommand IR Control With NetCommand for Hdmi CEC-Enabled Hdmi A/V ReceiverSource device connected directly to the TV Connecting a Computer to the TV This TV accepts digital computer signals only  Computer Video Connection Audio Video OutputUsing the TV with a Personal Computer Computer Video AdjustmentsImage Resolution Computer Display FormatsBefore You Begin Auto Input SensingConnection Types Picture QualityHdmi and Audio Signals 065Wall Outlet Cable no cable box Antennas with Separate UHF and VHF LeadsAntenna with a Single Lead VCR to an Antenna or Wall Outlet Cable 57CBDLQBOFM ODPNJOH DBCMFGSPN XbmmVCR VCR to a Cable Box Audio & Video Older Cable BoxAudio Video from Cable box To TVReceiver Sound System Using the TV’s Audio Output Receiver with Hdmi Output7SFDFJWFSCBDLQBOFM DVD playerCamcorder Audio-Only DeviceSleep Timer Choosing a Viewing SourceTV Tips Remote Control Adjust Up/Down/Left/Right Navigate menus and change settingsResetting the Remote Control Low-Battery IndicatorCare of the Remote Control Record/Playback KeysUsing ChannelView FeatureChannelView Channel Listings Press KeyStatus Display Ant 1TV-PG On-screen status displayFav Favorite Channels ANT-1TV Signals and Display Formats Signal DefinitionsDVD Image Definitions TV Display Format DefinitionsViewing Camera Files Jpeg Photos and the USB Photo PortMain menu USB Photo menuMedia Setup Menu Photos and Moving Video as Composite VideoSlide Show Keys for Jpeg Picture Slide Show3D Video Initial Set-UpTo Watch 3D Video To Watch Regular non-3D VideoRemote Control Keys for the TV Menu System Main MenuAV Menu AV Menu OptionsFilm Mode Auto, Off Video Mute On, OffGlobal Audio Only On, OffVideo Menu Video Menu OptionsVert Adjustment SharpEdge On, OffDeep Field ImagerAudio Menu Audio Menu OptionsANT1/ANT2 SAPCaptions Menu Captions on Analog ChannelsCaptions on Digital Channels Captions Menu OptionsSetup Menu Setup Menu Options1 Enter Setup menu, Edit channel options EditSetup menu, Clock options Timer Setup menu, Timer optionsEnergy Fast Power On Mode Low Power When Inputs NetCommand Hdmi Inputs MenuInputs Menu Options Selection menuLock Menu Pass CodesParent Menu Other Menu Alternate Rating SystemParent Menu Options U.S.-based rating system TV-YTV-Y7 TV-GOther Menu Options alternate rating system TimeAbout NetCommand IR Control Important Note on NetCommandIR Emitter Placement An IR emitter cable is included with the TVInitial NetCommand Setup for Most Devices If the device has no Power OFF key, skip this stepPower GuideCH/PAGE Operating NetCommand-Controlled Devices Controlling Most Device TypesSpecial Operation Methods Controlling an A/V Receiver Inside the Guide Outside the GuideSetting Up NetCommand Control of an A/V Receiver Receiver Control Power and VolumeSetup to Control A/V Receiver Power and Volume Before You BeginReceiver Control Automatic Audio Switching Audio Switching Setup 1 Audio from TV’s Audio OutputAudio Switching Setup 2 Audio from Source Device AV Receiver menu to set up audio switching Open the Inputs AV Receiver menuMore About Using an Hdmi Connection Setup to Control Switching to the TV’s Audio Output TV back panel Optional Analog orDigital audio With Hdmi Connection Display the Inputs AV Receiver menuNetCommand IR Control Device Connected to an A/V Receiver Ated Assign Input column Assign Input1 throughAssign Input5 Open the Inputs Learn menuAppendix a Specifications Depth Lbs WattsAppendix B Bypassing the Parental Lock Bypassing the Parental LockThis page intentionally left blank Appendix C Programming the Remote Control Functions Available for Other A/V DevicesProgramming the Remote Control DVDCABLE/SAT VCR DVD Audio Code VerificationProgramming Codes Make CodeCable Boxes Make Code CD Players Make CodeLaser Disc Players Make Code Receivers Make CodeSatellite Receivers Satellite Receivers Make CodeVCRs Make Code KEC DVD Players Make Code SVAIRT Appendix D Lamp-Cartridge Replacement and Cleaning Lamp LifeTo Order a New Lamp Lamp Part Number 915B403001Lamp-Cartridge Replacement Lamp-Cartridge Filter CleaningInstalling the New Lamp Cartridge Removing the Old Lamp CartridgeAppendix E NetCommand Hdmi Control of CEC Devices Enabling or Disabling the TV’s NetCommand Hdmi ControlConnecting Hdmi Devices to the TV NetCommand Hdmi Control is off Using NetCommand Hdmi Control Resetting Hdmi Control or Removing an Hdmi Device FigureCEC-enabled A/V receiver functions that may be available Appendix F Troubleshooting TV Reset Comparison GuideReset Name When to Use How to Use Resulting Action Service and Customer Support ServiceCustomer Support General TV Operation Symptom Remarks TV Channels Symptom Remarks TV Power On/Off Symptom RemarksPicture Symptom Remarks Symptom Remarks Indicators Symptom RemarksNetCommand IR Control Symptom Remarks Appendix F Troubleshooting Trademark and License Information Mitsubishi TV Software Mitsubishi DLP Projection Television Limited Warranty Warranty91 Index Index93 MDEAservice@mdea.com System Reset
Related manuals
Manual 71 pages 26.25 Kb Manual 71 pages 21.97 Kb