Mitsubishi Electronics WD-60C8 manual TV Channels Symptom Remarks, TV Power On/Off Symptom Remarks

Page 83

Appendices83

Appendix F: Troubleshooting, continued

TV Channels

Symptom

Remarks

1. The TV takes several seconds to respond to

• It is normal for digital channels to take longer to tune in.

channel changes.

• Press ENTER after a entering channel number to avoid delays.

 

• Use a 4-digit number for an over-the-air digital channel.

 

• Use a 6-digit number for digital cable channels if your cable service

 

is able to recognize 6-digit channel numbers.

2. You cannot access a channel.

• Use number keys instead of CH  /  .

Be sure the channel you want to view is in memory. See Setup >

Scan on page 43.

Check that the TV is switched to the correct device or antenna for that channel by pressing the INPUT key.

Make sure Channel Lock is off.

Make sure the Lock > Parent menu lock is set to off.

If you cannot tune to a virtual digital channel even though the TV has already memorized digital channels, tune to the physical channel number used by the broadcaster. The virtual channel will then be automatically added to memory.

3.

Name options are not available for some

You can name only memorized analog channels and memorized

 

channels.

digital channels not named by the broadcaster.

 

 

 

 

4.

When ChannelView list is displayed, informa-

Available information is sent from the broadcaster or cable

 

tion appears incomplete

 

provider. No other data is available.

 

 

Make sure the TV clock is set correctly.

TV Power On/Off

 

Symptom

Remarks

 

 

 

1.

TV takes an excessively long time to power

• When switched on, the TV needs time to boot up, just

 

on.

as a computer does. Also, the TV’s lamp requires a few

 

 

moments to heat up to full brightness.

 

 

• TV Energy Mode is set to Low Power. Change TV Energy

 

 

Mode to Fast Power On in the Setup menu.

 

 

 

2.

You cannot program the TV to turn on auto-

• The TV may be locked.

 

matically (Timer function)

• The clock may not be set.

 

 

• TV Energy Mode is set to Low Power. Change to Fast

 

 

Power On in Setup menu.

 

 

 

3.

The TV will not turn on after being plugged in.

If light on front panel is blinking, wait at least one and a half

 

 

minutes for the light to turn off, then press POWER again.

4.

TV turned itself off and the light on the front

• Momentary power fluctuation caused the TV to turn off to

 

panel started to blink.

prevent damage. Wait for the green light to stop flashing

 

 

and turn the TV on again.

 

 

• If the TV does not stay on, use the System Reset button on

 

 

the control panel. If this happens frequently, obtain an AC

 

 

line power conditioner/surge protector.

 

 

• An unusual digital signal may have been received, triggering a

 

 

protection circuit. Wait for the light to stop flashing and turn TV

 

 

on.

 

 

 

5.

TV turned itself off and the STATUS light is a

• The TV has overheated. Clear blocked air vents and ensure

 

steady yellow.

at least four inches of clearance on all sides of the TV.

 

 

• Clean the lamp-cartridge air filter. See Appendix D.

 

 

 

6.

TV will not power off.

Use the System Reset button.

 

 

 

Image 83
Contents WD-65835, WD-73835 WD-60C8, WD-65C8, WD-73C8WD-60735, WD-65735, WD-73735 WD-65736, WD-73736For Your Records Refer Servicing to Qualified Service PersonnelContents Internal Fans Installation NotesLamp Replacement Cleaning RecommendationsOutdoor Antenna Grounding Replacement PartsSpecial Features of Your TV Package ContentsFront Inputs TV Front PanelControl Panel Lamp Indicator Front-Panel IndicatorsPOWER/TIMER Indicator Status IndicatorComponent Video Input 1, Input TV Back PanelANT 1/ANT 2 Antenna Composite Video Input 1, InputHdmi Cable Categories IR NetCommand Output/External Controller InputHdmi Inputs High-Definition Multimedia Interface Audio L and R Input 1, InputInstalling the Remote Control Batteries Guidelines for Setting Up and Using Your New Widescreen TVWhen You First Power On the TV Assistance Additional TV SetupTV Operation TV CareMemorizing Channels Initial TV SetupSetting Up TV Inputs When You First Connect a DeviceTips on Auto Sensing and Changing Connected Devices Setup Procedure Setup Procedure for TV InputsDisconnecting an Analog A/V Receiver Auto Input/Auto Output Sensing ScreensWith NetCommand for Hdmi CEC-Enabled Hdmi A/V Receiver Controlling A/V Receiver Sound VolumeWith a Standard TV Setup With NetCommand IR ControlSource device connected directly to the TV Computer Video Connection Audio Video Output Connecting a Computer to the TVThis TV accepts digital computer signals only  Computer Display Formats Using the TV with a Personal ComputerComputer Video Adjustments Image ResolutionPicture Quality Before You BeginAuto Input Sensing Connection Types065 Hdmi and Audio SignalsAntenna with a Single Lead Wall Outlet Cable no cable boxAntennas with Separate UHF and VHF Leads VCR VCR to an Antenna or Wall Outlet Cable57CBDLQBOFM ODPNJOH DBCMFGSPN Xbmm Cable box To TV VCR to a Cable Box Audio & VideoOlder Cable Box Audio Video fromDVD player Receiver Sound System Using the TV’s Audio OutputReceiver with Hdmi Output 7SFDFJWFSCBDLQBOFMAudio-Only Device CamcorderTV Tips Sleep TimerChoosing a Viewing Source Adjust Up/Down/Left/Right Navigate menus and change settings Remote ControlRecord/Playback Keys Resetting the Remote ControlLow-Battery Indicator Care of the Remote ControlPress Key Using ChannelViewFeature ChannelView Channel ListingsOn-screen status display Status DisplayAnt 1 TV-PGANT-1 Fav Favorite ChannelsTV Display Format Definitions TV Signals and Display FormatsSignal Definitions DVD Image DefinitionsUSB Photo menu Viewing Camera FilesJpeg Photos and the USB Photo Port Main menuKeys for Jpeg Picture Slide Show Media Setup MenuPhotos and Moving Video as Composite Video Slide ShowTo Watch Regular non-3D Video 3D VideoInitial Set-Up To Watch 3D VideoMain Menu Remote Control Keys for the TV Menu SystemAV Menu Options AV MenuAudio Only On, Off Film Mode Auto, OffVideo Mute On, Off GlobalVideo Menu Options Video MenuImager Vert AdjustmentSharpEdge On, Off Deep FieldSAP Audio MenuAudio Menu Options ANT1/ANT2Captions Menu Options Captions MenuCaptions on Analog Channels Captions on Digital Channels1 Enter Setup MenuSetup Menu Options Edit Setup menu, Edit channel optionsSetup menu, Clock options Setup menu, Timer options TimerEnergy Fast Power On Mode Low Power Selection menu When Inputs NetCommand HdmiInputs Menu Inputs Menu OptionsOther Menu Alternate Rating System Lock MenuPass Codes Parent MenuTV-G Parent Menu Options U.S.-based rating systemTV-Y TV-Y7Time Other Menu Options alternate rating systemImportant Note on NetCommand About NetCommand IR ControlAn IR emitter cable is included with the TV IR Emitter PlacementIf the device has no Power OFF key, skip this step Initial NetCommand Setup for Most DevicesCH/PAGE PowerGuide Special Operation Methods Controlling an A/V Receiver Operating NetCommand-Controlled DevicesControlling Most Device Types Outside the Guide Inside the GuideBefore You Begin Setting Up NetCommand Control of an A/V ReceiverReceiver Control Power and Volume Setup to Control A/V Receiver Power and VolumeAudio Switching Setup 2 Audio from Source Device Receiver Control Automatic Audio SwitchingAudio Switching Setup 1 Audio from TV’s Audio Output Open the Inputs AV Receiver menu AV Receiver menu to set up audio switchingMore About Using an Hdmi Connection Display the Inputs AV Receiver menu Setup to Control Switching to the TV’s Audio OutputTV back panel Optional Analog or Digital audio With Hdmi ConnectionOpen the Inputs Learn menu NetCommand IR Control Device Connected to an A/V ReceiverAted Assign Input column Assign Input1 through Assign Input5Depth Lbs Watts Appendix a SpecificationsBypassing the Parental Lock Appendix B Bypassing the Parental LockThis page intentionally left blank Functions Available for Other A/V Devices Appendix C Programming the Remote ControlCode Verification Programming the Remote ControlDVD CABLE/SAT VCR DVD AudioCD Players Make Code Programming CodesMake Code Cable Boxes Make CodeReceivers Make Code Laser Disc Players Make CodeVCRs Make Code Satellite ReceiversSatellite Receivers Make Code KEC SVA DVD Players Make CodeIRT Lamp Part Number 915B403001 Appendix D Lamp-Cartridge Replacement and CleaningLamp Life To Order a New LampRemoving the Old Lamp Cartridge Lamp-Cartridge ReplacementLamp-Cartridge Filter Cleaning Installing the New Lamp CartridgeConnecting Hdmi Devices to the TV Appendix E NetCommand Hdmi Control of CEC DevicesEnabling or Disabling the TV’s NetCommand Hdmi Control NetCommand Hdmi Control is off CEC-enabled A/V receiver functions that may be available Using NetCommand Hdmi ControlResetting Hdmi Control or Removing an Hdmi Device Figure Reset Name When to Use How to Use Resulting Action Appendix F TroubleshootingTV Reset Comparison Guide Customer Support Service and Customer SupportService General TV Operation Symptom Remarks TV Power On/Off Symptom Remarks TV Channels Symptom RemarksPicture Symptom Remarks Indicators Symptom Remarks Symptom RemarksNetCommand IR Control Symptom Remarks Appendix F Troubleshooting Trademark and License Information Mitsubishi TV Software Mitsubishi DLP Projection Television Limited Warranty Warranty91 Index Index93 System Reset MDEAservice@mdea.com
Related manuals
Manual 71 pages 26.25 Kb Manual 71 pages 21.97 Kb