Mitsubishi Electronics WD-60C8 manual Lamp-Cartridge Replacement, Lamp-Cartridge Filter Cleaning

Page 76

76Appendices

Appendix D: Lamp-Cartridge Replacement and Cleaning, continued

Lamp-Cartridge Replacement

Removing the Old Lamp Cartridge

1.Turn off TV power and allow the lamp to cool for at least one hour before proceeding.

2.After the lamp has cooled, remove the cover of the lamp compartment, located on the back of the TV.

Refer to figures 1 and 2. Use a #2 (large) Phillips screwdriver to loosen the screw securing the cover. Keep the screw and cover for re-installation

3.With a large Phillips screwdriver, loosen the two shiny screws securing the lamp cartridge until they disengage from the mating threads. These are captive screws and cannot be separated from the lamp cartridge.

4.Fully open the bag supplied with the replacement lamp and set the opened bag aside.

5.Gently grasp the handle of the lamp cartridge and pull the old cartridge straight out. See figure 3.

CAUTION: Do not tilt or rotate the cartridge, as small glass fragments may fall out.

6.Without tilting or putting down the lamp cartridge, insert it into the opened bag. Close the bag while being careful not to let any glass particles fall out.

Installing the New Lamp Cartridge

1.Do not touch the glass parts of the new lamp car- tridge. Insert the new cartridge into the TV in the same orientation as the old cartridge. Push on the cartridge housing until it is fully seated.

2.With either your fingers or the screwdriver, gently tighten the two shiny screws. If using a screwdriver,

AVOID OVERTIGHTENING!

3.Replace the plastic cover and retaining screws.

4.WASH YOUR HANDS THOROUGHLY, AS THIS LAMP CONTAINS MERCURY.

Disposal of the Old Lamp Cartridge

Lamp under warranty: All lamps replaced under war- ranty must be returned to Mitsubishi. Use the return shipping label provided and send to Mitsubishi Digital Electronics, America, 1001 Cherry Drive, Suite 2, Brasel- ton, GA 30517.

IMPORTANT: Lamps found to be without defect will be returned and charged back to the sender.

Lamp no longer under warranty: Contact your local authorities or the Electronic Industries Alliance at www.eiae.org for lamp-disposal or recycling instructions. Do not dispose of the old lamp with common trash.

Figure 1

Figure 2

Figure 3

Use only replacement lamp part number 915B403001.

Lamp-Cartridge Filter Cleaning

If the TV shuts off after displaying the message “TV will shut down in a few seconds. Please check if the air flow is blocked ” and/or the STATUS LED is yellow, the air filter may need cleaning. The air filter is part of the lamp cartridge. Use the following procedure to clean the filter.

1.Remove the lamp cartridge from the TV as described under “Removing the Old Lamp Car- tridge.” Do not tilt or rotate the cartridge. Do not touch the glass parts of the lamp cartridge.

2.Holding the lamp cartridge horizontal (do not tilt or rotate), use a soft dry brush or vacuum cleaner to remove any dust that may be present on the mesh filter. Do not use liquids. See figure 4.

3.Reinstall the lamp cartridge as described under “Installing the New Lamp Cartridge.”

Figure 4

Keep lamp cartridge horizontal and remove dust from the mesh filter using a vacuum cleaner or soft dry brush.

Image 76
Contents WD-60C8, WD-65C8, WD-73C8 WD-60735, WD-65735, WD-73735WD-65736, WD-73736 WD-65835, WD-73835Refer Servicing to Qualified Service Personnel For Your RecordsContents Installation Notes Lamp ReplacementCleaning Recommendations Internal FansReplacement Parts Outdoor Antenna GroundingPackage Contents Special Features of Your TVControl Panel TV Front PanelFront Inputs Front-Panel Indicators POWER/TIMER IndicatorStatus Indicator Lamp IndicatorTV Back Panel ANT 1/ANT 2 AntennaComposite Video Input 1, Input Component Video Input 1, InputIR NetCommand Output/External Controller Input Hdmi Inputs High-Definition Multimedia InterfaceAudio L and R Input 1, Input Hdmi Cable CategoriesWhen You First Power On the TV Guidelines for Setting Up and Using Your New Widescreen TVInstalling the Remote Control Batteries Additional TV Setup TV OperationTV Care AssistanceInitial TV Setup Setting Up TV InputsWhen You First Connect a Device Memorizing ChannelsSetup Procedure Setup Procedure for TV Inputs Disconnecting an Analog A/V ReceiverAuto Input/Auto Output Sensing Screens Tips on Auto Sensing and Changing Connected DevicesControlling A/V Receiver Sound Volume With a Standard TV SetupWith NetCommand IR Control With NetCommand for Hdmi CEC-Enabled Hdmi A/V ReceiverSource device connected directly to the TV Connecting a Computer to the TV This TV accepts digital computer signals only  Computer Video Connection Audio Video OutputUsing the TV with a Personal Computer Computer Video AdjustmentsImage Resolution Computer Display FormatsBefore You Begin Auto Input SensingConnection Types Picture QualityHdmi and Audio Signals 065Antennas with Separate UHF and VHF Leads Wall Outlet Cable no cable boxAntenna with a Single Lead 57CBDLQBOFM ODPNJOH DBCMFGSPN Xbmm VCR to an Antenna or Wall Outlet CableVCR VCR to a Cable Box Audio & Video Older Cable BoxAudio Video from Cable box To TVReceiver Sound System Using the TV’s Audio Output Receiver with Hdmi Output7SFDFJWFSCBDLQBOFM DVD playerCamcorder Audio-Only DeviceChoosing a Viewing Source Sleep TimerTV Tips Remote Control Adjust Up/Down/Left/Right Navigate menus and change settingsResetting the Remote Control Low-Battery IndicatorCare of the Remote Control Record/Playback KeysUsing ChannelView FeatureChannelView Channel Listings Press KeyStatus Display Ant 1TV-PG On-screen status displayFav Favorite Channels ANT-1TV Signals and Display Formats Signal DefinitionsDVD Image Definitions TV Display Format DefinitionsViewing Camera Files Jpeg Photos and the USB Photo PortMain menu USB Photo menuMedia Setup Menu Photos and Moving Video as Composite VideoSlide Show Keys for Jpeg Picture Slide Show3D Video Initial Set-UpTo Watch 3D Video To Watch Regular non-3D VideoRemote Control Keys for the TV Menu System Main MenuAV Menu AV Menu OptionsFilm Mode Auto, Off Video Mute On, OffGlobal Audio Only On, OffVideo Menu Video Menu OptionsVert Adjustment SharpEdge On, OffDeep Field ImagerAudio Menu Audio Menu OptionsANT1/ANT2 SAPCaptions Menu Captions on Analog ChannelsCaptions on Digital Channels Captions Menu OptionsSetup Menu Options Setup Menu1 Enter Setup menu, Edit channel options EditSetup menu, Clock options Timer Setup menu, Timer optionsEnergy Fast Power On Mode Low Power When Inputs NetCommand Hdmi Inputs MenuInputs Menu Options Selection menuLock Menu Pass CodesParent Menu Other Menu Alternate Rating SystemParent Menu Options U.S.-based rating system TV-YTV-Y7 TV-GOther Menu Options alternate rating system TimeAbout NetCommand IR Control Important Note on NetCommandIR Emitter Placement An IR emitter cable is included with the TVInitial NetCommand Setup for Most Devices If the device has no Power OFF key, skip this stepGuide PowerCH/PAGE Controlling Most Device Types Operating NetCommand-Controlled DevicesSpecial Operation Methods Controlling an A/V Receiver Inside the Guide Outside the GuideSetting Up NetCommand Control of an A/V Receiver Receiver Control Power and VolumeSetup to Control A/V Receiver Power and Volume Before You BeginAudio Switching Setup 1 Audio from TV’s Audio Output Receiver Control Automatic Audio SwitchingAudio Switching Setup 2 Audio from Source Device AV Receiver menu to set up audio switching Open the Inputs AV Receiver menuMore About Using an Hdmi Connection Setup to Control Switching to the TV’s Audio Output TV back panel Optional Analog orDigital audio With Hdmi Connection Display the Inputs AV Receiver menuNetCommand IR Control Device Connected to an A/V Receiver Ated Assign Input column Assign Input1 throughAssign Input5 Open the Inputs Learn menuAppendix a Specifications Depth Lbs WattsAppendix B Bypassing the Parental Lock Bypassing the Parental LockThis page intentionally left blank Appendix C Programming the Remote Control Functions Available for Other A/V DevicesProgramming the Remote Control DVDCABLE/SAT VCR DVD Audio Code VerificationProgramming Codes Make CodeCable Boxes Make Code CD Players Make CodeLaser Disc Players Make Code Receivers Make CodeSatellite Receivers Make Code Satellite ReceiversVCRs Make Code KEC DVD Players Make Code SVAIRT Appendix D Lamp-Cartridge Replacement and Cleaning Lamp LifeTo Order a New Lamp Lamp Part Number 915B403001Lamp-Cartridge Replacement Lamp-Cartridge Filter CleaningInstalling the New Lamp Cartridge Removing the Old Lamp CartridgeEnabling or Disabling the TV’s NetCommand Hdmi Control Appendix E NetCommand Hdmi Control of CEC DevicesConnecting Hdmi Devices to the TV NetCommand Hdmi Control is off Resetting Hdmi Control or Removing an Hdmi Device Figure Using NetCommand Hdmi ControlCEC-enabled A/V receiver functions that may be available TV Reset Comparison Guide Appendix F TroubleshootingReset Name When to Use How to Use Resulting Action Service Service and Customer SupportCustomer Support General TV Operation Symptom Remarks TV Channels Symptom Remarks TV Power On/Off Symptom RemarksPicture Symptom Remarks Symptom Remarks Indicators Symptom RemarksNetCommand IR Control Symptom Remarks Appendix F Troubleshooting Trademark and License Information Mitsubishi TV Software Mitsubishi DLP Projection Television Limited Warranty Warranty91 Index Index93 MDEAservice@mdea.com System Reset
Related manuals
Manual 71 pages 26.25 Kb Manual 71 pages 21.97 Kb