Mitsubishi Electronics DX-TL1600EM Basic playback, Basic searching function, Time date search

Page 15

Basic playback

The recorded image can be played back in various ways. In this Basic Operations, the most basic playback function is explained. Refer to the pages shown below for the other playback functions.

Please refer to page 56 for Various playback functions.

1.Turn on the power of the connected peripheral recording device , then turn this unit on.

2.Select the playback device.

Press the PLAY DEVICE button on the front panel to select the playback device. The indicator of the selected device will illuminate. (The indicator will not switch when a peripheral recording device is not connected.)

PLAY DEVICE

3.Press the PLAY button.

After displaying a paused image, playback will begin.

The oldest recording will be played back when pressing the PLAY button for the first time after the power is turned on or the recording is finished. If you want to playback the newest recorded data, press the REV PLAY button before pressing the PLAY button after finishing recording.

4.Press the PAUSE button to pause playback.

Press the PAUSE button again to resume playback.

5.Press the STOP button to stop playback.

INFORMATION

When recording with more than

 

one camera, the playback interval per camera will be the time that multiplies the recording interval by the number of the cameras.

Basic searching function

This unit has various functions for searching a specific point. The following explains time date search. By using this function, you can search for a specified point of the data by setting the selected camera number, date, hour, and minutes. Refer to pages 57 - 59 for the other search- ing functions.

Time date search

Example: To search a recording which was made on May 17 2001, 9:25:40 p.m. by the camera number 3.

1.Press the SEARCH button to display the <SEARCH SELECTION> menu.

<SEARCH SELECTION>￿ @SELECTION CAMERA NO.ALL￿ TIME DATE SEARCH￿ INDEX SEARCH￿

SKIP SEARCH￿ ALARM LIST SEARCH￿

￿

￿

JUMP TO START POINT￿

￿

2.Make sure that the cursor ( ) is set to the <SELECTION CAMERA NO.> menu, and turn the SHUTTLE ring to the right.

The sub-item of <SELECTION CAMERA NO.> will start flashing.

<SEARCH SELECTION>￿ @SELECTION CAMERA NO.ALL￿ TIME DATE SEARCH￿ INDEX SEARCH￿

SKIP SEARCH￿ ALARM LIST SEARCH￿

￿

￿

JUMP TO START POINT￿

￿

3.Turn the JOG dial to display “ 3” then turn the SHUTTLE ring to the right.

• The flashing will stop.

<SEARCH SELECTION>￿ @SELECTION CAMERA NO. 3￿

TIME DATE SEARCH￿ INDEX SEARCH￿ SKIP SEARCH￿ ALARM LIST SEARCH￿

￿

￿

JUMP TO START POINT￿

￿

By turn the JOG dial, the selec- tion camera number will be changed as below :

ALL QWERTYU

rewq}{POI

4.Turn the JOG dial to select the TIME DATE SEARCH, and turn the SHUTTLE ring to the right.

The <TIME DATE SEARCH> menu will appear and the date number will start flashing.

<TIME DATE SEARCH>

3￿

￿

 

01-01-2000 00:00:00￿

 

￿

 

EXECUTE OFF

 

To exit the <TIME DATE SEARCH> menu with- out activating the search, press the SEARCH but-

ton on the front of the unit.

5.Turn the JOG dial to set the date number to 17.

Turn the SHUTTLE ring to the right. The next item will start flashing.

<TIME DATE SEARCH>

3￿

￿

 

05-01-2000 00:00:00￿

￿

EXECUTE OFF

6.Set the month, year, hour, minutes and seconds digit in a similar fashion.

The sub-item “OFF” will start flashing.

<TIME DATE SEARCH>

3

￿

17-05-2001 21:25:40￿

￿

EXECUTE OFF

ENGLISH

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

Basic Operations

15

Image 15
Contents DX-TL1600EM Features Unplug the Power Cord During a Long Absence Contents Communication settings Major operations and their functions Play button Play Device indicatorsPlay Mode buttons Play Device buttonMajor operations and their functions Terminals Exiting the menu How to use JOG dial and Shuttle ringSetting the character size Basic OperationsCamera mark will be shown on the present time dis- play Setting the present timeDaylight saving Present time displayBasic Operations Multiplexer functionsBasic recording Check the estimated recording time Setting the maximum recording fieldsPress the SET UP button to exit settings Example Choose Select REC Mode B the default setting is aSetting the define group Press the REC buttonPress the Stop button to stop recording Ton on the front of the unit Basic playbackBasic searching function Time date searchMAN Set the start time and end time of copying manually Press the Search button to clear the Time Date Search menuDisplay will return to the present time display Language selection settingYou can copy the data even during Recording Turn the Shuttle ring to the right to start copyingConnections Turning ON/OFF this Unit by peripheral sourceAttaching the ferrite core Peripheral devices to be connected Alarm Recording ConnectionConnecting with peripheral recording devices Connection when using several peripheral recording devicesConfirming the connected device Initial settingsHow to install an external hard disk drive Example Installing a 9GB hard disk drive to ID1Press the Power button again Setting this unit to delay the boot up timeMenu functions Main MenuSUB Menu Operations From **-**-** ****** to Menu functionsSetting character size How to set up / Various settingsHow to display menus Setting Display ModeVarious settings Be changed as follows Capacity remain settingCall OUT setting None No signal is emitted from the Call OUT terminalResetting the Archive Pointer Service menu settingBuzzer setting Power Failure listInitializing menus IM-CHECK Mode settingHDD repeat recording Initial set upClock setting Archive medium overwrite settingInitial SET UP menu will be displayed Auto-eject settingExample Setting Auto Eject to OFF the default is on Archive Data settingMotion Detection setting Backing up a data block containing the alarm recordBacking up a small alarm record FIFO/OVERWRITE Mode settingShowing the recorded period Information menuElapsed time display Values they will remain 2STurn the Shuttle ring twice to the right Quick settingRDD Menu Data Loading setting Menu Data Saving RDD setting CommandsMaximum recording fields setting Various recording settingsVarious recording settings Image quality settingWill be changed as follows Various recording settingsWhen the is assigned, the camera is disabled Changed as followsGround the Alarm in terminal Tection setting in the Initial SET UP menu is onCamera Alarm Rec setting Pre-alarm recording settingMotion menu will appear DET settingCH. motion detection setting Selection camera noSetting the detection mask Sensitivity settingTurn the Shuttle ring to the left to finish setting Test Mode menu will appear Motion threshold settingTest mode setting To finish setting, turn the Shuttle ring to the leftIng the SPLIT/SEQUENCE button How to use the Zoom buttonAge will appear pixelized when enlarged Multiplexer functionsHow to use the camera number buttons Multiplexer functionsSPLIT/SEQUENCE button Multiplexer display Screen SW Pattern settingsSplit 4 Screen setting Split 9 Screen settingImage quality of split screen Please change settingsSplit 16 Screen setting Sequence settingSelected pattern will start flashing Camera title settingDisplaying the title Maximum of 30 seconds can be setRepeat Steps 4 and 5 to input Exit Alarm display settingOperation examples Operation example 1 Simultaneous Backup using the TimerExample of a system using the following peripherals Record settings are made as followsOperation example Making backups as neededOperation examples Operation example 2 Endless Repeat recordingSettings for Motion Detection Setting are made as follows Settings for Timer Program are made as followsComplete the program setting Using the TimerSetting the Timer Timer Setting screenEstimating recording when using the Timer Press the Timer REC buttonTo set other programs, repeat steps 5 through Medium of the peripheral device Using the TimerOverlapping Timer settings DET Application settingAlarm Recording Using the Timer / Alarm RecordingPlease refer to Basic recording on page 12 for details Pre-alarm RecordingVarious recordings Repeat RecordingSeries Recording Series Recording menu settings for both unitsDisplay the Initial SET UP menu Flashing will move to capacity settingVarious playback functions Time date search Monitor display settings and playback operationVarious playback functions / Various search High-speed fast-forward/high-speed rewindSkip Search Alarm List SearchHow to count index signals Various searchCopying from the hard disk to the copying device Various search / Using peripheral devices / Making copiesJump to Start point oldest recording Scsi ID number allocationRestoring items from the archive device to the hard disk Setting of Copy rangeMaking copies Restoring items onto the hard disk from the copying deviceCancelling Copy operation Making copies / Making backupsBackup operation Procedure for settingIndividual settings during Backup operation Making backupsPower failure time display Making backups / Other convenient functionsTimer Backup Power failure reset recordingOther convenient functions Power failure compensation circuitPassword Lock function Example Changing passwordsConnecting with a personal computer Communication settings / Connecting to a personal computerRS-232C settings TCP / IP settingsCommand code and status Connecting to a personal computer / Command codesCommand codes Commands Functions Status, when normal executeDetails of the numbers Initial Setup Service Power Failure Rear Terminal Normal REC SettingTime Date Adjust Communication SettingSmall 1 Large FS1 Split Screen SettingCF? SA?Selected Pattern 1 ~ SKP Skip PWR Power ARC Archive AEJ EjectSPLIT4 AC?Superior QR? DW?PP? Basic Standard MediumStandard Medium Power 3 RemainAS1 AS0Remain AlarmprotFS2 RearArchive Device HDD RESTORE, OverwriteDevice RJ?HDD Near END Backup Near OvertakeBackup System Error RC***AOMain Devicehdd Others~ 1 0 PWR-OFF 1 CONFIG/INITIALIZE Status code Meaning of status Table of Error CodeError code Meaning of error Table of Status CodeCharacter Search Character Search commandsCommands Functions Status,when normal execute Character SearchSample operation Character SearchRecording duration is set to Medium Pre-alarm recording time tableRecording time table Recording duration is set to LongDevice does not respond TroubleshootingIs the Lock indicator light on? Operate Copying device/archiveGlossary Troubleshooting / GlossaryIs peripheral device’s Scsi ID setting set correctly? Check the Access indicator19,20 Canceling27,28 60-6310kΩ5V Input22kΩ terminal 047∝F Specifications872C273B5