Mitsubishi Electronics DX-TL1600EM operation manual Various playback functions

Page 56

Various playback functions

Playing still frames

1. Press the PAUSE button during playback.

The unit will shift into still frame mode. By pressing the PAUSE button once again, the unit will return to its previ- ous mode.

By pressing the Camera number button while the still frame is displayed, the unit will search for that channel’s images and immediately display them on-screen.

Turn the JOG dial to the right to move forward one frame and to the left to move back one frame. Continue turning the JOG dial to the right for forward playback of consecu- tive frames and to the left for reverse playback of consecu- tive frames. Stop turning the dial for still frame viewing.

During frame-by-frame playback in single-screen display mode, playback will lag behind rapid JOG dial rotation be- cause the unit is simultaneously engaged in searching for images in the displayed channel.

Shuttle viewing

The SHUTTLE ring can be used to adjust playback speed to varying rates. Playback speed will vary according to how far the SHUTTLE ring is turned.

1.Press the PAUSE button during playback, and then turn the SHUTTLE ring.

3

4

5

 

2

 

6

1

 

7

1Reverse speed search (1MB units)

2Reverse speed search (skip 5fields)

3Reverse speed search (skip 3fields)

4Still frame playback

5Forward speed search (skip 3fields)

6Forward speed search (skip 5fields)

7Forward speed search (1MB units)

The unit will shift to still frame playback mode when the SHUTTLE ring is returned to its former

position.

Shuttle hold

By pressing the PAUSE button during playback (or reverse playback), the unit will shift into still frame mode. Rotate the SHUTTLE ring in the desired direction and to the de- sired search speed, then press the PAUSE button while holding the SHUTTLE ring to position. Search speed will be maintained even when the SHUTTLE ring is returned to its original position.

Direct shuttle viewing

Direct shuttle playback can be activated by turning the SHUTTLE ring during playback or reverse playback.

1. Turn the SHUTTLE ring during playback.

Please refer to the above diagram for the playback speed.

The unit will shift to regular playback mode when the SHUTTLE ring is returned to its former position.

INFORMATION

When playback images recorded at different recording intervals, there may be rare

occasions when playback speed differs from the original recording rate.

Frame-by-frame playback

1.Turn the JOG dial in either direction during still frame playback.

Reverse playback

1.Press the REV PLAY button when the unit is not in operation.

The unit will begin reverse playback.

On the first reverse playback after the power switch is turned on or after recording, the unit will

start by displaying the last recorded image.

Changing playback intervals

When the PLAY or REV PLAY button is pressed while the unit is in operation, playback will occur at the same inter- vals as the recorded intervals. Playback intervals can be changed, when the PLAY or REV PLAY button is pressed while the unit is in playback or reverse playback operation.

Playback intervals can be confirmed on-screen by using the single-screen display mode and enter-

ing “2” or “3” in the DISPLAY MODE setting of the <TIME DATE DISPLAY> menu.

Playback or reverse playback intervals are increased up when the PLAY button is pressed, and playback or reverse playback intervals are slowed down when the REV PLAY button is pressed.

INFORMATION

This is a convenient function for slow viewing of recordings with fast movement as

well as fast playback of images captured at long recording intervals.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••

56

Image 56
Contents DX-TL1600EM Features Unplug the Power Cord During a Long Absence Contents Communication settings Major operations and their functions Play Device indicators Play Mode buttonsPlay Device button Play buttonMajor operations and their functions Terminals How to use JOG dial and Shuttle ring Setting the character sizeBasic Operations Exiting the menuSetting the present time Daylight savingPresent time display Camera mark will be shown on the present time dis- playBasic recording Basic OperationsMultiplexer functions Setting the maximum recording fields Press the SET UP button to exit settingsExample Choose Select REC Mode B the default setting is a Check the estimated recording timePress the Stop button to stop recording Setting the define groupPress the REC button Basic playback Basic searching functionTime date search Ton on the front of the unitPress the Search button to clear the Time Date Search menu MAN Set the start time and end time of copying manuallyLanguage selection setting You can copy the data even during RecordingTurn the Shuttle ring to the right to start copying Display will return to the present time displayAttaching the ferrite core ConnectionsTurning ON/OFF this Unit by peripheral source Alarm Recording Connection Connecting with peripheral recording devicesConnection when using several peripheral recording devices Peripheral devices to be connectedInitial settings How to install an external hard disk driveExample Installing a 9GB hard disk drive to ID1 Confirming the connected deviceSetting this unit to delay the boot up time Press the Power button againSUB Menu Menu functionsMain Menu Operations Menu functions From **-**-** ****** toHow to set up / Various settings How to display menusSetting Display Mode Setting character sizeVarious settings Capacity remain setting Call OUT settingNone No signal is emitted from the Call OUT terminal Be changed as followsService menu setting Buzzer settingPower Failure list Resetting the Archive PointerIM-CHECK Mode setting Initializing menusInitial set up Clock settingArchive medium overwrite setting HDD repeat recordingAuto-eject setting Example Setting Auto Eject to OFF the default is onArchive Data setting Initial SET UP menu will be displayedBacking up a data block containing the alarm record Backing up a small alarm recordFIFO/OVERWRITE Mode setting Motion Detection settingInformation menu Elapsed time displayValues they will remain 2S Showing the recorded periodQuick setting RDD Menu Data Loading setting Menu Data Saving RDD settingCommands Turn the Shuttle ring twice to the rightVarious recording settings Various recording settingsImage quality setting Maximum recording fields settingVarious recording settings When the is assigned, the camera is disabledChanged as follows Will be changed as followsTection setting in the Initial SET UP menu is on Camera Alarm Rec settingPre-alarm recording setting Ground the Alarm in terminalDET setting CH. motion detection settingSelection camera no Motion menu will appearTurn the Shuttle ring to the left to finish setting Setting the detection maskSensitivity setting Motion threshold setting Test mode settingTo finish setting, turn the Shuttle ring to the left Test Mode menu will appearHow to use the Zoom button Age will appear pixelized when enlargedMultiplexer functions Ing the SPLIT/SEQUENCE buttonSPLIT/SEQUENCE button How to use the camera number buttonsMultiplexer functions Screen SW Pattern settings Split 4 Screen settingSplit 9 Screen setting Multiplexer displayPlease change settings Split 16 Screen settingSequence setting Image quality of split screenCamera title setting Displaying the titleMaximum of 30 seconds can be set Selected pattern will start flashingAlarm display setting Repeat Steps 4 and 5 to input ExitOperation example 1 Simultaneous Backup using the Timer Example of a system using the following peripheralsRecord settings are made as follows Operation examplesMaking backups as needed Operation examplesOperation example 2 Endless Repeat recording Operation exampleSettings for Timer Program are made as follows Settings for Motion Detection Setting are made as followsUsing the Timer Setting the TimerTimer Setting screen Complete the program settingTo set other programs, repeat steps 5 through Estimating recording when using the TimerPress the Timer REC button Using the Timer Overlapping Timer settingsDET Application setting Medium of the peripheral deviceUsing the Timer / Alarm Recording Alarm RecordingPre-alarm Recording Various recordingsRepeat Recording Please refer to Basic recording on page 12 for detailsSeries Recording menu settings for both units Display the Initial SET UP menuFlashing will move to capacity setting Series RecordingVarious playback functions Monitor display settings and playback operation Various playback functions / Various searchHigh-speed fast-forward/high-speed rewind Time date searchAlarm List Search How to count index signalsVarious search Skip SearchVarious search / Using peripheral devices / Making copies Jump to Start point oldest recordingScsi ID number allocation Copying from the hard disk to the copying deviceSetting of Copy range Making copiesRestoring items onto the hard disk from the copying device Restoring items from the archive device to the hard diskMaking copies / Making backups Backup operationProcedure for setting Cancelling Copy operationMaking backups Individual settings during Backup operationMaking backups / Other convenient functions Timer BackupPower failure reset recording Power failure time displayPower failure compensation circuit Password Lock functionExample Changing passwords Other convenient functionsCommunication settings / Connecting to a personal computer RS-232C settingsTCP / IP settings Connecting with a personal computerConnecting to a personal computer / Command codes Command code and statusDetails of the numbers Command codesCommands Functions Status, when normal execute Normal REC Setting Time Date AdjustCommunication Setting Initial Setup Service Power Failure Rear TerminalSplit Screen Setting CF?SA? Small 1 Large FS1SKP Skip PWR Power ARC Archive AEJ Eject SPLIT4AC? Selected Pattern 1 ~DW? PP?Basic Standard Medium Superior QR?Power 3 Remain AS1AS0 Standard MediumAlarmprot FS2Rear RemainHDD RESTORE, Overwrite DeviceRJ? Archive DeviceBackup Near Overtake Backup System ErrorRC***AO HDD Near ENDOthers Main Devicehdd~ 1 0 PWR-OFF 1 CONFIG/INITIALIZE Table of Error Code Error code Meaning of errorTable of Status Code Status code Meaning of statusCharacter Search commands Commands Functions Status,when normal executeCharacter Search Character SearchCharacter Search Sample operationPre-alarm recording time table Recording time tableRecording duration is set to Long Recording duration is set to MediumTroubleshooting Is the Lock indicator light on? OperateCopying device/archive Device does not respondTroubleshooting / Glossary Is peripheral device’s Scsi ID setting set correctly?Check the Access indicator GlossaryCanceling 27,2860-63 19,20Specifications 10kΩ5V Input22kΩ terminal 047∝F872C273B5