Mitsubishi Electronics DX-TL1600EM operation manual Various search, Skip Search, Alarm List Search

Page 58

Various search (continued)

Can not change the display, during the search selection menu will appear.

6.To play back search results.

Press either the PLAY button or the PAUSE button.

Refer to page 56 for details on Various playback functions.

To exit the <INDEX SEARCH> menu without ac- tivating the search, press the SEARCH button on

the front of the unit.

7.Press the STOP button to stop playback and still frame mode.

Press the SEARCH button, the display will revert to its original state.

How to count index signals

Present time in the diagram below represents the point of playing back or stopped playing back. To search index with

+”, turn the SHUTTLE ring to the right to search forward. To search index with “ - ”, turn the SHUTTLE ring to the left to search backward.

A•REC: Alarm Recording

Present position

 

-15

-2

-1

+1 +2

+15

A•REC

A•REC

A•REC

A•REC A•REC

A•REC

Beginning of playback device

End of playback device

Skip Search

Skip Search is a process where the unit automatically searches for an index signal, then retrieves the visuals associated with that index and plays back the images for 5 seconds each to select the camera number.

To play back search results, press the PLAY but- ton for the desired image.

1.Press the SEARCH button to display by the <SEARCH SELECTION> menu. Setting the <SELECTION CAMERA NO.> menu, repeat the steps 2, 3 of the INDEX SEARCH setting procedures.

2.Turn the JOG dial to select the SKIP SEARCH, and turn the SHUTTLE ring to the right.

•The <SKIP SEARCH> menu will appear .

<SEARCH SELECTION>￿ SELECTION CAMERA NO. 5￿ TIME DATE SEARCH￿ INDEX SEARCH￿

@SKIP SEARCH￿ ALARM LIST SEARCH￿

￿

￿

￿

JUMP TO START POINT

3.Turn the SHUTTLE ring to desired direction (Forward search to the right and reverse to the left).

The unit begins the Index Search, and plays back the images associated to the index for five seconds each. Playback is displayed on a SPLIT 16 screen when “ALL” is selected in the SELECTION CAMERA NO. setting, and displayed on a single screen when an individual camera number is selected.

<SKIP SEARCH>

5

￿

TURN THE SHUTTLE RING￿

<<OR >> TO￿

PREVIEW EACH ALARM.

The unit cannot be selected to single screen dis- play mode during Skip Search.

4. Press the STOP button to stop searching.

When reverse SKIP SEARCH is used on recorded content that includes five seconds or less of alarm

recording, those five seconds or less of alarm re- cording may be played back repeatedly. If this hap- pens, press the stop button to halt SKIP SEARCH, use reverse playback to get past the content being played back repeatedly, and then resume with re- verse SKIP SEARCH.

Alarm List Search

When Alarm Recording is initiated (refer to page 53), the Alarm Recording start time will be added to the Alarm List. Alarm List Search is a process which uses the associated Alarm Recording start time to retrieve a desired image for still frame playback to select the camera number.

Up to 800 Alarm Recording start-times can be registered. After the 800th time, the first start-time

will be erased and the 801st start-time will be added to the list.

1.Press the SEARCH button to display by the <SEARCH SELECTION> menu. Setting the <SELECTION CAMERA NO.> menu, repeat the steps 2, 3 of the INDEX SEARCH setting procedures.

2.Turn the JOG dial to select the ALARM LIST SEARCH, and turn the SHUTTLE ring to the right.

•The <ALARM LIST SEARCH> menu will appear .

<SEARCH SELECTION>￿ SELECTION CAMERA NO. 5￿ TIME DATE SEARCH￿ INDEX SEARCH￿

SKIP SEARCH￿ @ALARM LIST SEARCH￿

￿

￿

￿

JUMP TO START POINT

3.Turn the JOG dial till the cursor goes to desired alarm list number, then turn the SHUTTLE ring to the right.

The unit begins the Alarm List Search, and retrieves the image associated with the selected time (or the time closest to the selected time).

Playback is displayed on a SPLIT 16 screen when “ALL” is selected in the SELECTION CAMERA NO. setting, and displayed on a single screen when an individual camera number is selected.

<ALARM LIST SEARCH>￿

C

No.

DATE

TIME

0003 26-01-01

18:54:25

5

0002 26-01-01

18:34:40

5

@0001 25-01-01

18:20:00

5

The JOG dial can be used to move the cursor line-by-line through the list. When the cursor reaches

either the top or the bottom of the list, the <ALARM LIST SEARCH> menu will scroll to the next page. To move through the pages, place the cursor over “No.”, and turn the SHUTTLE ring.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••

58

Image 58
Contents DX-TL1600EM Features Unplug the Power Cord During a Long Absence Contents Communication settings Major operations and their functions Play Device button Play Device indicatorsPlay Mode buttons Play buttonMajor operations and their functions Terminals Basic Operations How to use JOG dial and Shuttle ringSetting the character size Exiting the menuPresent time display Setting the present timeDaylight saving Camera mark will be shown on the present time dis- playMultiplexer functions Basic OperationsBasic recording Example Choose Select REC Mode B the default setting is a Setting the maximum recording fieldsPress the SET UP button to exit settings Check the estimated recording timePress the REC button Setting the define groupPress the Stop button to stop recording Time date search Basic playbackBasic searching function Ton on the front of the unitPress the Search button to clear the Time Date Search menu MAN Set the start time and end time of copying manuallyTurn the Shuttle ring to the right to start copying Language selection settingYou can copy the data even during Recording Display will return to the present time displayTurning ON/OFF this Unit by peripheral source ConnectionsAttaching the ferrite core Connection when using several peripheral recording devices Alarm Recording ConnectionConnecting with peripheral recording devices Peripheral devices to be connectedExample Installing a 9GB hard disk drive to ID1 Initial settingsHow to install an external hard disk drive Confirming the connected deviceSetting this unit to delay the boot up time Press the Power button againMain Menu Menu functionsSUB Menu Operations Menu functions From **-**-** ****** toSetting Display Mode How to set up / Various settingsHow to display menus Setting character sizeVarious settings None No signal is emitted from the Call OUT terminal Capacity remain settingCall OUT setting Be changed as followsPower Failure list Service menu settingBuzzer setting Resetting the Archive PointerIM-CHECK Mode setting Initializing menusArchive medium overwrite setting Initial set upClock setting HDD repeat recordingArchive Data setting Auto-eject settingExample Setting Auto Eject to OFF the default is on Initial SET UP menu will be displayedFIFO/OVERWRITE Mode setting Backing up a data block containing the alarm recordBacking up a small alarm record Motion Detection settingValues they will remain 2S Information menuElapsed time display Showing the recorded periodCommands Quick settingRDD Menu Data Loading setting Menu Data Saving RDD setting Turn the Shuttle ring twice to the rightImage quality setting Various recording settingsVarious recording settings Maximum recording fields settingChanged as follows Various recording settingsWhen the is assigned, the camera is disabled Will be changed as followsPre-alarm recording setting Tection setting in the Initial SET UP menu is onCamera Alarm Rec setting Ground the Alarm in terminalSelection camera no DET settingCH. motion detection setting Motion menu will appearSensitivity setting Setting the detection maskTurn the Shuttle ring to the left to finish setting To finish setting, turn the Shuttle ring to the left Motion threshold settingTest mode setting Test Mode menu will appearMultiplexer functions How to use the Zoom buttonAge will appear pixelized when enlarged Ing the SPLIT/SEQUENCE buttonMultiplexer functions How to use the camera number buttonsSPLIT/SEQUENCE button Split 9 Screen setting Screen SW Pattern settingsSplit 4 Screen setting Multiplexer displaySequence setting Please change settingsSplit 16 Screen setting Image quality of split screenMaximum of 30 seconds can be set Camera title settingDisplaying the title Selected pattern will start flashingAlarm display setting Repeat Steps 4 and 5 to input ExitRecord settings are made as follows Operation example 1 Simultaneous Backup using the TimerExample of a system using the following peripherals Operation examplesOperation example 2 Endless Repeat recording Making backups as neededOperation examples Operation exampleSettings for Timer Program are made as follows Settings for Motion Detection Setting are made as followsTimer Setting screen Using the TimerSetting the Timer Complete the program settingPress the Timer REC button Estimating recording when using the TimerTo set other programs, repeat steps 5 through DET Application setting Using the TimerOverlapping Timer settings Medium of the peripheral deviceUsing the Timer / Alarm Recording Alarm RecordingRepeat Recording Pre-alarm RecordingVarious recordings Please refer to Basic recording on page 12 for detailsFlashing will move to capacity setting Series Recording menu settings for both unitsDisplay the Initial SET UP menu Series RecordingVarious playback functions High-speed fast-forward/high-speed rewind Monitor display settings and playback operationVarious playback functions / Various search Time date searchVarious search Alarm List SearchHow to count index signals Skip SearchScsi ID number allocation Various search / Using peripheral devices / Making copiesJump to Start point oldest recording Copying from the hard disk to the copying deviceRestoring items onto the hard disk from the copying device Setting of Copy rangeMaking copies Restoring items from the archive device to the hard diskProcedure for setting Making copies / Making backupsBackup operation Cancelling Copy operationMaking backups Individual settings during Backup operationPower failure reset recording Making backups / Other convenient functionsTimer Backup Power failure time displayExample Changing passwords Power failure compensation circuitPassword Lock function Other convenient functionsTCP / IP settings Communication settings / Connecting to a personal computerRS-232C settings Connecting with a personal computerConnecting to a personal computer / Command codes Command code and statusCommands Functions Status, when normal execute Command codesDetails of the numbers Communication Setting Normal REC SettingTime Date Adjust Initial Setup Service Power Failure Rear TerminalSA? Split Screen SettingCF? Small 1 Large FS1AC? SKP Skip PWR Power ARC Archive AEJ EjectSPLIT4 Selected Pattern 1 ~Basic Standard Medium DW?PP? Superior QR?AS0 Power 3 RemainAS1 Standard MediumRear AlarmprotFS2 RemainRJ? HDD RESTORE, OverwriteDevice Archive DeviceRC***AO Backup Near OvertakeBackup System Error HDD Near ENDOthers Main Devicehdd~ 1 0 PWR-OFF 1 CONFIG/INITIALIZE Table of Status Code Table of Error CodeError code Meaning of error Status code Meaning of statusCharacter Search Character Search commandsCommands Functions Status,when normal execute Character SearchCharacter Search Sample operationRecording duration is set to Long Pre-alarm recording time tableRecording time table Recording duration is set to MediumCopying device/archive TroubleshootingIs the Lock indicator light on? Operate Device does not respondCheck the Access indicator Troubleshooting / GlossaryIs peripheral device’s Scsi ID setting set correctly? Glossary60-63 Canceling27,28 19,20Specifications 10kΩ5V Input22kΩ terminal 047∝F872C273B5