Mitsubishi Electronics DX-TL1600EM Press the Search button to clear the Time Date Search menu

Page 16

Basic Operations (continued)

7. Turn the JOG dial to select “ON”.

<TIME DATE SEARCH>

3￿

￿

 

17-05-2001 21:25:40￿

￿

EXECUTE ON￿

TURN THE SHUTTLE RING￿

>>TO EXECUTE.

8.Turn the SHUTTLE ring to the right to execute.

•The time date search will start and pause the playback display at the specified time point to select the camera number (or the nearest point from the specified time).

17-05-2001 21:25:40 C03

Search results are displayed on a SPLIT 16 screen when “ALL” is selected in the SELECTION CAMERA

NO. setting, and displayed on a single screen when an individual camera number is selected.

To change the search image from SPLIT 16 screen to the single screen, select the camera

number by pressing the Camera number button on the front of this unit. The selected image will be shown on the Single screen mode.

If there is no recording or no data which is re- corded on the date you have set, the time date

search will not be activated and the date number will start flashing again.

9.To play back the searched image.

•Press either the PLAY button or the PAUSE button.

INFORMATION

Press the SEARCH button to clear the <TIME DATE SEARCH> menu.

10.Press the STOP button to stop playback and still frame mode.

•Press the SEARCH button, the display will revert to its original state.

4.Press the COPY button.

•The <COPY SELECTION> menu will appear.

5.Make sure that the cursor ( ) is next to the COPY DIRECTION, and turn the SHUTTLE ring to the right.

•The sub-item will be different depending on the connected devices.

•Use JOG dial to choose the desired device to copy to and turn the SHUTTLE ring to the right to enter the selection.

<COPY SELECTION>￿

@COPY DIRECTION HDD}COPY￿

OVERWRITEOFF￿

TRANSFER PERIOD MAN￿ FROM:29-01-01 09:25:24

6.Turn the JOG dial to move the cursor to OVERWRITE and turn the SHUTTLE ring to the right.

•The default setting is “OFF”. You have to select whether to overwrite previous recorded data (ON) or copying from the end of the recording exists on the media (OFF). Turn the JOG dial to make the desired setting to flash, then turn the SHUTTLE ring to the right to enter the selection.

<COPY SELECTION>￿

COPY DIRECTION HDD}COPY￿

@OVERWRITEOFF￿

TRANSFER PERIOD MAN￿ FROM:29-01-01 09:25:24

<COPY SELECTION>￿

COPY DIRECTION HDD}COPY￿

@OVERWRITEON￿

TRANSFER PERIOD MAN￿ FROM:29-01-01 09:25:24

INFORMATION

The following sub-items can be set for the overwrite copying:

•If you set to “ON”, the copy will start from the very beginning of the media.

•If you set to “OFF”, the copy will start from the end of the last recorded part of the media.

7.Set the TRANSFER PERIOD.

•Turn the JOG dial to move the cursor next to the “TRANSFER

PERIOD” then turn the SHUTTLE ring to the right. The sub- item of “MAN” (manual) will start flashing.

<COPY SELECTION>￿

COPY DIRECTION HDD}COPY￿

OVERWRITEOFF￿

@TRANSFER PERIOD MAN￿ FROM:29-01-01 09:25:24

■Copying the data from HDD to a copying device or an archive device

This unit can copy the data which is recorded on hard disk drive to an archive device media or a copying device me- dia. The following explains how to copy the data manually.

Make sure that the peripheral recording device is connected and set correctly before you start copying.

1.Turn on the power of the peripheral recording device connected to the unit.

2.Turn on the power of the digital unit.

3.Insert media to archive device Glossary or a copying device

Glossary .

The following sub-item can be set for the “TRANSFER PERIOD” of copying.

By turning the JOG dial, the sub-item will be changed as below:

MANS/E

“MAN”: Set the start time and end time of copying manually.

“S/E”: Copy all data from the start to the end of the device which is recognized as a device to copy from.

8.Turn the JOG dial to move the cursor to the start time (FROM), and set the date, month, year, hour, minute and second of the data to copy from.

•Turn the JOG dial to set the start time.

•Turn the SHUTTLE ring to the right to enter the selection.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

•••••••••••••

•

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents DX-TL1600EM Features Unplug the Power Cord During a Long Absence Contents Communication settings Major operations and their functions Play Device indicators Play Mode buttonsPlay Device button Play buttonMajor operations and their functions Terminals How to use JOG dial and Shuttle ring Setting the character sizeBasic Operations Exiting the menuSetting the present time Daylight savingPresent time display Camera mark will be shown on the present time dis- playMultiplexer functions Basic OperationsBasic recording Setting the maximum recording fields Press the SET UP button to exit settingsExample Choose Select REC Mode B the default setting is a Check the estimated recording timePress the REC button Setting the define groupPress the Stop button to stop recording Basic playback Basic searching functionTime date search Ton on the front of the unitPress the Search button to clear the Time Date Search menu MAN Set the start time and end time of copying manuallyLanguage selection setting You can copy the data even during RecordingTurn the Shuttle ring to the right to start copying Display will return to the present time displayTurning ON/OFF this Unit by peripheral source ConnectionsAttaching the ferrite core Alarm Recording Connection Connecting with peripheral recording devicesConnection when using several peripheral recording devices Peripheral devices to be connectedInitial settings How to install an external hard disk driveExample Installing a 9GB hard disk drive to ID1 Confirming the connected deviceSetting this unit to delay the boot up time Press the Power button againMain Menu Menu functionsSUB Menu Operations Menu functions From **-**-** ****** toHow to set up / Various settings How to display menusSetting Display Mode Setting character sizeVarious settings Capacity remain setting Call OUT settingNone No signal is emitted from the Call OUT terminal Be changed as followsService menu setting Buzzer settingPower Failure list Resetting the Archive PointerIM-CHECK Mode setting Initializing menusInitial set up Clock settingArchive medium overwrite setting HDD repeat recordingAuto-eject setting Example Setting Auto Eject to OFF the default is onArchive Data setting Initial SET UP menu will be displayedBacking up a data block containing the alarm record Backing up a small alarm recordFIFO/OVERWRITE Mode setting Motion Detection settingInformation menu Elapsed time displayValues they will remain 2S Showing the recorded periodQuick setting RDD Menu Data Loading setting Menu Data Saving RDD settingCommands Turn the Shuttle ring twice to the rightVarious recording settings Various recording settingsImage quality setting Maximum recording fields settingVarious recording settings When the is assigned, the camera is disabledChanged as follows Will be changed as followsTection setting in the Initial SET UP menu is on Camera Alarm Rec settingPre-alarm recording setting Ground the Alarm in terminalDET setting CH. motion detection settingSelection camera no Motion menu will appearSensitivity setting Setting the detection maskTurn the Shuttle ring to the left to finish setting Motion threshold setting Test mode settingTo finish setting, turn the Shuttle ring to the left Test Mode menu will appearHow to use the Zoom button Age will appear pixelized when enlargedMultiplexer functions Ing the SPLIT/SEQUENCE buttonMultiplexer functions How to use the camera number buttonsSPLIT/SEQUENCE button Screen SW Pattern settings Split 4 Screen settingSplit 9 Screen setting Multiplexer displayPlease change settings Split 16 Screen settingSequence setting Image quality of split screenCamera title setting Displaying the titleMaximum of 30 seconds can be set Selected pattern will start flashingAlarm display setting Repeat Steps 4 and 5 to input ExitOperation example 1 Simultaneous Backup using the Timer Example of a system using the following peripheralsRecord settings are made as follows Operation examplesMaking backups as needed Operation examplesOperation example 2 Endless Repeat recording Operation exampleSettings for Timer Program are made as follows Settings for Motion Detection Setting are made as followsUsing the Timer Setting the TimerTimer Setting screen Complete the program settingPress the Timer REC button Estimating recording when using the TimerTo set other programs, repeat steps 5 through Using the Timer Overlapping Timer settingsDET Application setting Medium of the peripheral deviceUsing the Timer / Alarm Recording Alarm RecordingPre-alarm Recording Various recordingsRepeat Recording Please refer to Basic recording on page 12 for detailsSeries Recording menu settings for both units Display the Initial SET UP menuFlashing will move to capacity setting Series RecordingVarious playback functions Monitor display settings and playback operation Various playback functions / Various searchHigh-speed fast-forward/high-speed rewind Time date searchAlarm List Search How to count index signalsVarious search Skip SearchVarious search / Using peripheral devices / Making copies Jump to Start point oldest recordingScsi ID number allocation Copying from the hard disk to the copying deviceSetting of Copy range Making copiesRestoring items onto the hard disk from the copying device Restoring items from the archive device to the hard diskMaking copies / Making backups Backup operationProcedure for setting Cancelling Copy operationMaking backups Individual settings during Backup operationMaking backups / Other convenient functions Timer BackupPower failure reset recording Power failure time displayPower failure compensation circuit Password Lock functionExample Changing passwords Other convenient functionsCommunication settings / Connecting to a personal computer RS-232C settingsTCP / IP settings Connecting with a personal computerConnecting to a personal computer / Command codes Command code and statusCommands Functions Status, when normal execute Command codesDetails of the numbers Normal REC Setting Time Date AdjustCommunication Setting Initial Setup Service Power Failure Rear TerminalSplit Screen Setting CF?SA? Small 1 Large FS1SKP Skip PWR Power ARC Archive AEJ Eject SPLIT4AC? Selected Pattern 1 ~DW? PP?Basic Standard Medium Superior QR?Power 3 Remain AS1AS0 Standard MediumAlarmprot FS2Rear RemainHDD RESTORE, Overwrite DeviceRJ? Archive DeviceBackup Near Overtake Backup System ErrorRC***AO HDD Near ENDOthers Main Devicehdd~ 1 0 PWR-OFF 1 CONFIG/INITIALIZE Table of Error Code Error code Meaning of errorTable of Status Code Status code Meaning of statusCharacter Search commands Commands Functions Status,when normal executeCharacter Search Character SearchCharacter Search Sample operationPre-alarm recording time table Recording time tableRecording duration is set to Long Recording duration is set to MediumTroubleshooting Is the Lock indicator light on? OperateCopying device/archive Device does not respondTroubleshooting / Glossary Is peripheral device’s Scsi ID setting set correctly?Check the Access indicator GlossaryCanceling 27,2860-63 19,20Specifications 10kΩ5V Input22kΩ terminal 047∝F872C273B5
Top Page Image Contents