Mitsubishi Electronics DX-TL1600EM Service menu setting, Buzzer setting, Power Failure list

Page 28

Various settings (continued)

6.Turn the JOG dial until the cursor is next to “ARCHIVE” and turn the SHUTTLE ring to the right.

•The sub-item will start flashing.

<CALL OUT>￿

HDD(ID:0~3) FULL￿

@ARCHIVE(ID:4) NONE

7.Turn the JOG dial to flash “20%” and turn the SHUTTLE ring to the right.

•The sub-item stops flashing.

<CALL OUT>￿

HDD(ID:0~3) 10%

@ARCHIVE(ID:4) 20%

8.Turn the SHUTTLE ring to the left or press the SET UP button.

♦Buzzer setting

You can set to sound a buzzer warning when the remain- ing storage capacity of the Hard Disk Drive reaches the amount set in CAPACITY REMAIN setting on the <REAR TERMINAL> menu. In addition to the above setting of CALL OUT setting section, it is also possible to sound the buzzer when other errors occur.

To sound the buzzer when the remaining storage capacity reaches the preset amount.

1)Select “REMAIN” of BUZZER in the <REAR TER- MINAL > menu.

2)Set the device and its remaining storage capac- ity of CAPACITY REMAIN in the <REAR TERMI- NAL> menu.

Example: Setting BUZZER to “REMAIN” (the default set- ting is “KEY”).

1.Display the <MENU SETTING> menu and turn the JOG dial until the cursor is next to REAR TERMINAL. Then turn the SHUTTLE ring to the right.

•The <REAR TERMINAL> menu appears.

<REAR

TERMINAL>￿

REMAIN￿

@MODE

OUT

CAPACITY REMAIN HDD-10%

￿

OUT

 

CALL

 

2.Turn the JOG dial until the cursor is next to BUZZER and turn the SHUTTLE ring to the right to flash the sub-item.

CALL OUT￿

KEY￿

@BUZZER

￿

 

 

 

3.Turn the JOG dial to show “REMAIN” and turn the SHUTTLE ring to the right to complete setting.

•The sub-item stops flashing.

CALL OUT￿

@BUZZERREMAIN￿

By turning the JOG dial, the item of BUZZER shown on the screen switches as shown below.

KEY WRNG REMAIN OFF

“KEY”: The buzzer sounds when any button is pressed, or JOG dial or SHUTTLE ring is turned.

“WRNG”: The buzzer sounds when a warning oc- curs. Refer to page 84, “Warnings and CALL OUT output”, for details.

“REMAIN”: The buzzer sounds when the remaining storage capacity of main HDD and ARCHIVE reaches the preset amount selected in CAPACITY REMAIN. Press WARNING RESET button to stop the buzzer.

“OFF”: The buzzer does not sound.

4.Turn the SHUTTLE ring to the left or press the SET UP button.

■Service menu setting

In the <SERVICE> menu, you can see the power failure time, reset the Archive Pointer, initialize menus and IM- CHECK mode.

♦Power Failure list

The list of times when the power failure occurred is available.

Example: Displaying POWER FAILURE list.

Up to 50 power failure start times are shown on the list. If more than 50 times, the last 50 start times

are shown.

1.Display the <MENU SETTING > menu and turn the JOG dial until the cursor is next to SERVICE. Turn the SHUTTLE ring to the right.

•The <SERVICE> menu appears.

<SERVICE>￿

 

@POWER FAILURE￿

OFF￿

ARCHIVE POINT RESET

MENU INITIALIZE

OFF￿

IM-CHECK MODE

OFF

2.Check that the cursor is next to POWER FAILURE and turn the SHUTTLE ring to the right.

<POWER FAILURE>￿

No. DATE TIME INFO.￿ 02 25-01-01 12:02 PW-LOS￿ 01 23-01-01 12:35 PW-LOS￿

￿

•The <POWER FAILURE> list appears on the screen.

•The number of times, the date and the time when the power failure occurred are given on the list.

To reset the power failure start time, press the WARNING RESET button when the <POWER FAIL-

URE> list is shown on the screen.

3.Turn the SHUTTLE ring to the left or press the SET UP button.

♦Resetting the Archive Pointer

This unit writes down an Archive Pointer Glossary indicat- ing where the last archive stopped. In the next archive, it starts from the point where the Archive Pointer is last placed. If you want to reset this Archive Pointer, follow the steps shown below.

1.Press the SET UP button to display the <MENU SETTING> menu.

2.Move the cursor next to SERVICE then turn the SHUTTLE ring to the right.

•The <SERVICE> menu appears.

<SERVICE>￿

 

@POWER FAILURE￿

OFF￿

ARCHIVE POINT RESET

MENU INITIALIZE

OFF￿

IM-CHECK MODE

OFF

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

••••••••••••

•

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents DX-TL1600EM Features Unplug the Power Cord During a Long Absence Contents Communication settings Major operations and their functions Play Device indicators Play Mode buttonsPlay Device button Play buttonMajor operations and their functions Terminals How to use JOG dial and Shuttle ring Setting the character sizeBasic Operations Exiting the menuSetting the present time Daylight savingPresent time display Camera mark will be shown on the present time dis- playMultiplexer functions Basic OperationsBasic recording Setting the maximum recording fields Press the SET UP button to exit settingsExample Choose Select REC Mode B the default setting is a Check the estimated recording timePress the REC button Setting the define groupPress the Stop button to stop recording Basic playback Basic searching functionTime date search Ton on the front of the unitPress the Search button to clear the Time Date Search menu MAN Set the start time and end time of copying manuallyLanguage selection setting You can copy the data even during RecordingTurn the Shuttle ring to the right to start copying Display will return to the present time displayTurning ON/OFF this Unit by peripheral source ConnectionsAttaching the ferrite core Alarm Recording Connection Connecting with peripheral recording devicesConnection when using several peripheral recording devices Peripheral devices to be connectedInitial settings How to install an external hard disk driveExample Installing a 9GB hard disk drive to ID1 Confirming the connected deviceSetting this unit to delay the boot up time Press the Power button againMain Menu Menu functionsSUB Menu Operations Menu functions From **-**-** ****** toHow to set up / Various settings How to display menusSetting Display Mode Setting character sizeVarious settings Capacity remain setting Call OUT settingNone No signal is emitted from the Call OUT terminal Be changed as followsService menu setting Buzzer settingPower Failure list Resetting the Archive PointerIM-CHECK Mode setting Initializing menusInitial set up Clock settingArchive medium overwrite setting HDD repeat recordingAuto-eject setting Example Setting Auto Eject to OFF the default is onArchive Data setting Initial SET UP menu will be displayedBacking up a data block containing the alarm record Backing up a small alarm recordFIFO/OVERWRITE Mode setting Motion Detection settingInformation menu Elapsed time displayValues they will remain 2S Showing the recorded periodQuick setting RDD Menu Data Loading setting Menu Data Saving RDD settingCommands Turn the Shuttle ring twice to the rightVarious recording settings Various recording settingsImage quality setting Maximum recording fields settingVarious recording settings When the is assigned, the camera is disabledChanged as follows Will be changed as followsTection setting in the Initial SET UP menu is on Camera Alarm Rec settingPre-alarm recording setting Ground the Alarm in terminalDET setting CH. motion detection settingSelection camera no Motion menu will appearSensitivity setting Setting the detection maskTurn the Shuttle ring to the left to finish setting Motion threshold setting Test mode settingTo finish setting, turn the Shuttle ring to the left Test Mode menu will appearHow to use the Zoom button Age will appear pixelized when enlargedMultiplexer functions Ing the SPLIT/SEQUENCE buttonMultiplexer functions How to use the camera number buttonsSPLIT/SEQUENCE button Screen SW Pattern settings Split 4 Screen settingSplit 9 Screen setting Multiplexer displayPlease change settings Split 16 Screen settingSequence setting Image quality of split screenCamera title setting Displaying the titleMaximum of 30 seconds can be set Selected pattern will start flashingAlarm display setting Repeat Steps 4 and 5 to input ExitOperation example 1 Simultaneous Backup using the Timer Example of a system using the following peripheralsRecord settings are made as follows Operation examplesMaking backups as needed Operation examplesOperation example 2 Endless Repeat recording Operation exampleSettings for Timer Program are made as follows Settings for Motion Detection Setting are made as followsUsing the Timer Setting the TimerTimer Setting screen Complete the program settingPress the Timer REC button Estimating recording when using the TimerTo set other programs, repeat steps 5 through Using the Timer Overlapping Timer settingsDET Application setting Medium of the peripheral deviceUsing the Timer / Alarm Recording Alarm RecordingPre-alarm Recording Various recordingsRepeat Recording Please refer to Basic recording on page 12 for detailsSeries Recording menu settings for both units Display the Initial SET UP menuFlashing will move to capacity setting Series RecordingVarious playback functions Monitor display settings and playback operation Various playback functions / Various searchHigh-speed fast-forward/high-speed rewind Time date searchAlarm List Search How to count index signalsVarious search Skip SearchVarious search / Using peripheral devices / Making copies Jump to Start point oldest recordingScsi ID number allocation Copying from the hard disk to the copying deviceSetting of Copy range Making copiesRestoring items onto the hard disk from the copying device Restoring items from the archive device to the hard diskMaking copies / Making backups Backup operationProcedure for setting Cancelling Copy operationMaking backups Individual settings during Backup operationMaking backups / Other convenient functions Timer BackupPower failure reset recording Power failure time displayPower failure compensation circuit Password Lock functionExample Changing passwords Other convenient functionsCommunication settings / Connecting to a personal computer RS-232C settingsTCP / IP settings Connecting with a personal computerConnecting to a personal computer / Command codes Command code and statusCommands Functions Status, when normal execute Command codesDetails of the numbers Normal REC Setting Time Date AdjustCommunication Setting Initial Setup Service Power Failure Rear TerminalSplit Screen Setting CF?SA? Small 1 Large FS1SKP Skip PWR Power ARC Archive AEJ Eject SPLIT4AC? Selected Pattern 1 ~DW? PP?Basic Standard Medium Superior QR?Power 3 Remain AS1AS0 Standard MediumAlarmprot FS2Rear RemainHDD RESTORE, Overwrite DeviceRJ? Archive DeviceBackup Near Overtake Backup System ErrorRC***AO HDD Near ENDOthers Main Devicehdd~ 1 0 PWR-OFF 1 CONFIG/INITIALIZE Table of Error Code Error code Meaning of errorTable of Status Code Status code Meaning of statusCharacter Search commands Commands Functions Status,when normal executeCharacter Search Character SearchCharacter Search Sample operationPre-alarm recording time table Recording time tableRecording duration is set to Long Recording duration is set to MediumTroubleshooting Is the Lock indicator light on? OperateCopying device/archive Device does not respondTroubleshooting / Glossary Is peripheral device’s Scsi ID setting set correctly?Check the Access indicator GlossaryCanceling 27,2860-63 19,20Specifications 10kΩ5V Input22kΩ terminal 047∝F872C273B5
Top Page Image Contents