Mitsubishi Electronics DX-TL1600EM operation manual Estimating recording when using the Timer

Page 51

11.To set other programs, repeat steps 5 through 10.

Up to 8 programs can be set per screen.

To erase a program entry, press the “WARNING RESET” button during the programming procedure.

12.Turn the SHUTTLE ring to the right or press the SET UP button.

Turning the SHUTTLE ring to the left moves the cursor to the previous entry. Pressing the SET UP button closes the <TIMER PROGRAM> menu.

13.Press the TIMER REC button.

The TIMER REC indicator illuminate.

If the current time is covered by a program, the unit will begin recording immediately.

If the current time is not covered by a program, the unit will turn the power off and go into stand-by mode.

Operation can be shut down completely by pressing the TIMER REC button once more.

“SKIP”: This is set when timer recording is to be paused temporarily.Then the power will be switched off and the specified time period for that program number will not be recorded.

“POWER”: During the specified time, the power sup- ply is stopped in “ON” condition. This is used for execution of alarm recording during timer reserva- tion.

“ARC”(ARCHIVE): The recording contents of the HDD are backed up to the backup device.

“EJECT”: After backup of the recording contents of the HDD to the backup device, the medium is ejected automatically.

Estimating recording when using the Timer

Please note when using the Timer that there may be instances where, because of max recording fields, image quality, there is insufficient recording space on the unit’s hard disk drive to complete the Timer recording as programmed.

Please note that when the max recording fields setting differs on the NORMAL REC SETTING screen and TIMER PROGRAM screen, its possible record- ing duration will differ from the duration displayed in ESTD TIME on the NORMAL REC SETTING screen.

When setting the Timer for multiple programs, please refer to the Recording Time table on page 81 to con- firm the amount of hard disk space the recording du- ration will take up under different setting conditions.

<TIMER PROGRAM>

P2￿

DW

START

END

MODE￿

1 DAY

12:00

13:00 AÐ 25￿

@DAY 16:00 22:00 AÐ12.5￿

3 ÐÐÐ ÐÐ:ÐÐ ÐÐ:ÐÐ ÐÐÐÐÐÐ￿

Using the Timer setting as an example of estimating possible recording duration, the chart on next column shows that everything is recorded on the 4th day, and on the 5th day only remain 7.8% of Program 2 content is recorded on the hard disk drive. (Conditions ; Image Quality is set to “HIGH”, built-in 60GB hard disk drive. )

Program

Recording time

Possible duration for

HDD recording

for one day (A)

Consecutive Recording (B)

space (A/B)

 

 

 

 

 

1

60 minutes

1104 minutes

5.4%

 

 

 

 

2

360 minutes

2209 minutes

16.3%

 

 

 

 

Setting SPECIAL DW (special day of the week) By entering a program’s start-day and end-day, the unit can be set to record during a specific time frame over any number of days in the week. The unit will record on the days entered into the program which displays “SPL” in its DW column.

Example: MON - FRI are designated as the days used in DEFINE P1.

The settings for the start-day and the end-day cannot be identical.

1.Press the SET UP button to display the <MENU SETTING> menu.Turn the JOG dial to move the cursor to TIMER PROGRAM then turn the SHUTTLE ring to the right.

The <TIMER PROGRAM> menu will appear.

2.Turn the JOG dial to move the cursor to DEFINE P1 then turn the SHUTTLE ring to the right to display the <TIMER PROGRAM> menu of P1.

<TIMER PROGRAM>￿

SELECTED PATTERN￿ P1 @DEFINE P1￿

DEFINE P2￿

DEFINE P3

3.Turn the JOG dial to move the cursor to select “SPECIAL DW”, then turn the SHUTTLE ring to the right.

7

SPL

12:00

13:00

A-

25￿

8

DAY

13:00

14:25

B-

1￿

@SPECIAL DW:TUEÐFRI

4.Turn the JOG dial to select “MON” then turn the SHUTTLE ring to the right.

7

SPL

12:00

13:00

A-

25￿

8

DAY

13:00

14:25

B-

1￿

@SPECIAL DW:MONÐFRI

5.Turn the JOG dial to select “FRI” then turn the SHUTTLE ring to the right.

The flashing will stop.

7

SPL

12:00

13:00

A-

25￿

8

DAY

13:00

14:25

B-

1￿

@SPECIAL DW:MONÐFRI

6.Press the TIMER REC button.

The TIMER REC indicator will illuminate.

If the current time is covered by a program, the unit will begin recording immediately.

If the current time is not covered by a program, the unit will turn the power off and go into stand-by mode.

Operation can be shut down completely by pressing the TIMER REC button once more.

The unit will not record if there is an error in Timer settings. The following provides a list of measures for dealing with errors in Timer settings.

ENGLISH

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

Operations

51

Image 51
Contents DX-TL1600EM Features Unplug the Power Cord During a Long Absence Contents Communication settings Major operations and their functions Play button Play Device indicatorsPlay Mode buttons Play Device buttonMajor operations and their functions Terminals Exiting the menu How to use JOG dial and Shuttle ringSetting the character size Basic OperationsCamera mark will be shown on the present time dis- play Setting the present timeDaylight saving Present time displayBasic Operations Multiplexer functionsBasic recording Check the estimated recording time Setting the maximum recording fieldsPress the SET UP button to exit settings Example Choose Select REC Mode B the default setting is aSetting the define group Press the REC buttonPress the Stop button to stop recording Ton on the front of the unit Basic playbackBasic searching function Time date searchMAN Set the start time and end time of copying manually Press the Search button to clear the Time Date Search menuDisplay will return to the present time display Language selection settingYou can copy the data even during Recording Turn the Shuttle ring to the right to start copyingConnections Turning ON/OFF this Unit by peripheral sourceAttaching the ferrite core Peripheral devices to be connected Alarm Recording ConnectionConnecting with peripheral recording devices Connection when using several peripheral recording devicesConfirming the connected device Initial settingsHow to install an external hard disk drive Example Installing a 9GB hard disk drive to ID1Press the Power button again Setting this unit to delay the boot up timeMenu functions Main MenuSUB Menu Operations From **-**-** ****** to Menu functionsSetting character size How to set up / Various settingsHow to display menus Setting Display ModeVarious settings Be changed as follows Capacity remain settingCall OUT setting None No signal is emitted from the Call OUT terminalResetting the Archive Pointer Service menu settingBuzzer setting Power Failure listInitializing menus IM-CHECK Mode settingHDD repeat recording Initial set upClock setting Archive medium overwrite settingInitial SET UP menu will be displayed Auto-eject settingExample Setting Auto Eject to OFF the default is on Archive Data settingMotion Detection setting Backing up a data block containing the alarm recordBacking up a small alarm record FIFO/OVERWRITE Mode settingShowing the recorded period Information menuElapsed time display Values they will remain 2STurn the Shuttle ring twice to the right Quick settingRDD Menu Data Loading setting Menu Data Saving RDD setting CommandsMaximum recording fields setting Various recording settingsVarious recording settings Image quality settingWill be changed as follows Various recording settingsWhen the is assigned, the camera is disabled Changed as followsGround the Alarm in terminal Tection setting in the Initial SET UP menu is onCamera Alarm Rec setting Pre-alarm recording settingMotion menu will appear DET settingCH. motion detection setting Selection camera noSetting the detection mask Sensitivity settingTurn the Shuttle ring to the left to finish setting Test Mode menu will appear Motion threshold settingTest mode setting To finish setting, turn the Shuttle ring to the leftIng the SPLIT/SEQUENCE button How to use the Zoom buttonAge will appear pixelized when enlarged Multiplexer functionsHow to use the camera number buttons Multiplexer functionsSPLIT/SEQUENCE button Multiplexer display Screen SW Pattern settingsSplit 4 Screen setting Split 9 Screen settingImage quality of split screen Please change settingsSplit 16 Screen setting Sequence settingSelected pattern will start flashing Camera title settingDisplaying the title Maximum of 30 seconds can be setRepeat Steps 4 and 5 to input Exit Alarm display settingOperation examples Operation example 1 Simultaneous Backup using the TimerExample of a system using the following peripherals Record settings are made as followsOperation example Making backups as neededOperation examples Operation example 2 Endless Repeat recordingSettings for Motion Detection Setting are made as follows Settings for Timer Program are made as followsComplete the program setting Using the TimerSetting the Timer Timer Setting screenEstimating recording when using the Timer Press the Timer REC buttonTo set other programs, repeat steps 5 through Medium of the peripheral device Using the TimerOverlapping Timer settings DET Application settingAlarm Recording Using the Timer / Alarm RecordingPlease refer to Basic recording on page 12 for details Pre-alarm RecordingVarious recordings Repeat RecordingSeries Recording Series Recording menu settings for both unitsDisplay the Initial SET UP menu Flashing will move to capacity settingVarious playback functions Time date search Monitor display settings and playback operationVarious playback functions / Various search High-speed fast-forward/high-speed rewindSkip Search Alarm List SearchHow to count index signals Various searchCopying from the hard disk to the copying device Various search / Using peripheral devices / Making copiesJump to Start point oldest recording Scsi ID number allocationRestoring items from the archive device to the hard disk Setting of Copy rangeMaking copies Restoring items onto the hard disk from the copying deviceCancelling Copy operation Making copies / Making backupsBackup operation Procedure for settingIndividual settings during Backup operation Making backupsPower failure time display Making backups / Other convenient functionsTimer Backup Power failure reset recordingOther convenient functions Power failure compensation circuitPassword Lock function Example Changing passwordsConnecting with a personal computer Communication settings / Connecting to a personal computerRS-232C settings TCP / IP settingsCommand code and status Connecting to a personal computer / Command codesCommand codes Commands Functions Status, when normal executeDetails of the numbers Initial Setup Service Power Failure Rear Terminal Normal REC SettingTime Date Adjust Communication SettingSmall 1 Large FS1 Split Screen SettingCF? SA?Selected Pattern 1 ~ SKP Skip PWR Power ARC Archive AEJ EjectSPLIT4 AC?Superior QR? DW?PP? Basic Standard MediumStandard Medium Power 3 RemainAS1 AS0Remain AlarmprotFS2 RearArchive Device HDD RESTORE, OverwriteDevice RJ?HDD Near END Backup Near OvertakeBackup System Error RC***AOMain Devicehdd Others~ 1 0 PWR-OFF 1 CONFIG/INITIALIZE Status code Meaning of status Table of Error CodeError code Meaning of error Table of Status CodeCharacter Search Character Search commandsCommands Functions Status,when normal execute Character SearchSample operation Character SearchRecording duration is set to Medium Pre-alarm recording time tableRecording time table Recording duration is set to LongDevice does not respond TroubleshootingIs the Lock indicator light on? Operate Copying device/archiveGlossary Troubleshooting / GlossaryIs peripheral device’s Scsi ID setting set correctly? Check the Access indicator19,20 Canceling27,28 60-6310kΩ5V Input22kΩ terminal 047∝F Specifications872C273B5