Mitsubishi Electronics DX-TL5000U instruction manual LAN B Communication Setting

Page 79

LAN B (Communication) Setting

This item is used to make the communication settings between this unit and the PC connected via LAN B.

System Menu

1 COM/LAN

step 7

3 LAN B (Communication) Setting

step 1

1 LAN B Address Setting

step 2

2 Service Port Setting

step 3

3 E-mail Notification Information

step 4

D E-mail Notification Detailed Infomation

step 5

4 IP Alarm Notification Information

step 6

D Alarm Notification Detailed Infomation

Using the web function of this unit is required to input “E-Mail Address” and “Recorder ID.”

(E-mail Notification Detailed Information)

step4. Check the contents to be transmitted to the PC.

Remain: Transmits signal when the remaining capacity reaches the value set for Call out setting. Temp/Fan: Transmits signal when the high temperature is detected or the fan is stopped.

Reboot: Transmits signal when the unit is rebooted.

Record: Transmits signal when the recording is started.

Alarm: Transmits signal when the alarm recording is started.

Sensor: Transmits signal when the signal is input to the terminal on the rear panel.

Using the web function of this unit is required to change the contents to be transmitted.

(IP Alarm Notification Information)

step5. Check the settings of “IP Address” and “Target Port.”

This item is used to transmit warning signals or signals of status change such as a closure of a rear terminal to the PC connected.

When selecting “Test,” the sending test for the set IP address and port is executed.

(LAN B Address Setting)

step1. Set the IP address, sub net mask, and Gateway.

MAC address is shown on the bottom of the screen of <LAN B (Communication) Setting>.

Do not assign the same IP address or network address for LAN A and LAN B.

Do not assign “000.000.000.000” to IP address and broadcast address. If this address is assigned, communications or any other functions of this unit may not be performed correctly.

The setting cannot be changed during recording. Stop recording before changing the setting.

(Service Port Setting)

step2. Set the port setting of “Web,” “User Access,” and “Administrator.”

This item is used to set the port number which is necessary to connect a PC.

Normally, leave the setting as is.

Do not change the setting without sufficient knowledge about the network setting.

When making the settings other than the port settings of “Web,” “User Access,” and “Administrator,” using the specified application is required. Consult your dealer about the specified application.

(E-mail Notification Information)

step3. Check the settings of “E-Mail Address” and “Recorder ID.”

When selecting “Mail,” the e-mail is sent for the selected address.

Using the specified application is required to change the IP address and target port. Consult your dealer about the specified application.

Transmission of signal to broadcast address is not supported.

(Alarm Notification Detailed Information)

step6. Check the contents to be transmitted to the PC.

Remain: Transmits signal when the remaining capacity reaches the value set for Call out setting. Temp/Fan: Transmits signal when the high temperature is detected or the fan is stopped.

Reboot: Transmits signal when the unit is rebooted.

Record: Transmits signal when the recording is started.

Alarm: Transmits signal when the alarm recording is started.

Sensor: Transmits signal when the signal is input to the terminal on the rear panel.

Using the specified application is required to change the contents to be transmitted. Consult your dealer about the specified application.

step7. Select “Return” in the screen of <LAN B (Communication) Setting>.

When the setting of “IP Address,” “Sub Net Mask,” “Gateway,” or “Service Port Setting” is changed, the power turns off automatically and then the unit restarts.

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations

75

Image 79
Contents DX-TL5000U Page Beginning AvertissementIii Important safeguardsServicing Damage requiring ServiceReplacement Parts Safety CheckUnplug the Power Cord During a Long Absence Recordable time and product warranty Installation Location and Handling Beginning Features Beginning Contents 85-89 System Menu74-76 80-83Flowchart for connection and settings FlowchartSearching the recorded data Setting the motion detectionSetting the timer recording Timer recording is executed and completedMajor operations and their functions Output A/B button Busy indicatorDET DOT ON/OFF/M-DET Area SET UP Camera Number 9 Camera control buttonsTimer button Power buttonAnalogue Output connectors SET UP buttonVideo Cascade connectors Main switchAC power socket Camera connectors16. RS485 IN/OUT connectors Alarm in terminalsAlarm OUT terminals Reset buttonConnections Connecting to Cctv camera, monitor, and sensorConnections Alarm recording connection Keyboard DX-KB5UE Cascade connectionAttaching or removing the HDD Precautions for attaching or removing the HDDRemove the HDD tray When removing a HDDRemove the metal part Disconnect the cables Remove the front coversAttach the new HDD onto the HDD tray with four screws When attaching a HDDFix the metal part with four screws Attach the front covers Page Clamping the cables Connecting to an analogue video cassette recorderRecommended items Optional itemsAttaching the optional board Setting a menu with a mouse How to set the menusSetting the menus Setting the menu using a mouse Setting a mouseClosing a menu screen Displaying a menu screenSelecting an item For some items, more detailed setting is required Using the front buttons of the unitUsing a mouse Setting parametersAddress number using the front buttons of the unit Symbols in the menusFor the first time. The Wizard enables a quick setup Setup WizardSetup Wizard Setup wizard is displayed when the unit is turned onWhen selecting Next Set the HDD configurationWhen selecting Partition Set the desired partition capacity Select whether or not to make the recording settingsMenu chart Menu chartExit Menu chartFunctions AudioFunctions Pages Recording Menu chartEasy + D Set 213 2ED Exit Exits the Recording menu Multiplexer Setting Option COM/LAN Functions Pages Service Info Memory Functions Pages NextData Clear Search Steps 1, 2 Search by MotionSet the motion detection conditions for playback Select Search OperationsCopy Data to Copy 2 Drive/Set Copy 2 Drive Select Other settings and then set the detailed settingsCopy Copy Data to Copy 1 Drive/Set Copy 1 DriveSet the start time of copy Copying the data of this unit to a video cassetteOperational panel Playback softwareSystem requirements Starting up the application softwareView menu Search menuOperation menu Bookmark menuMain device Information/AudioInformation AudioSee page 88 for registering a book mark Select Protect Protect DataProtect Data Set the start and end points of the data to be lockedPTZ control using the front panel buttons PTZ control using the menuPTZ Control Recording Settings concerning normal recording and alarm recordingSet Recording Pattern a Normal/Timer to D Timer Pre-alarm recordingSet the pre-alarm recording time in Pre-Alarm Duration Normal recording settingsAlarm recording settings Set the alarm modeSet the recording camera for each sensor connected Set the PTZ camera presetAlarm recording Alarm InputRecording Emergency Recording SetupCamera Setting Long pre-alarm recordingSet the audio recording for each camera from 1 to Audio Recording SetupSet the audio recording mode Alarm area with the picture. See OperationsCarrying out timer recording TimerTimer Setting the programExample Overlapped timer settingsSet the reference interval time Motion DetSteps 1, 3, 4, 5 Color of the dot detecting motion changes Menu Language Selection Time/Date SettingRear Terminal Setting SystemKey Sound Call Out SettingsBuzzer Password Setting Changing the Password For the disk management passwordActivating the Password Lock Releasing the Password Lock For the levels 1Sequence button operations To cancel the sequential displayCamera number button operations Split buttons operationsOperations Single sequential screen Sequence Single Multiplexer SettingOutput a Settings Split screenOutput B Settings Select output a or output B Alarm Display SettingSet the covert camera setting for each camera number Covert Camera SettingCamera On Screen Display SettingOn Screen Information ClockMonitor Output Adjust Audio SettingRecorder Title This item is used to reset the menu settings Reset to Factory SettingLoad Menu Data Menu DataSave Menu Data Option XGA Monitor SettingsSelect the display mode of the XGA output Select the sharpness settingRS-485 Cascade Setting RS-232C SettingLAN B Communication Setting Device Information LAN a NAS SettingLAN a Address Setting Select Return in the screen of LAN a NAS SettingPTZ Camera Configuration PTZ SettingConfiguration Check List Disk Information Service InfoSystem Log List Elapsed Operating TimeSet the camera number to be restored RestoreSet the other detailed settings External HDD MemoryAdd/Remove HDD Device Internal HDDScsi ID0 Scsi ID1 Scsi ID2 Scsi ID3 Scsi ID4 Scsi ID5 Attaching the HDD and setting the ID numberAdd/Remove DVD/CD Drive Data Management Setting for Main MemoryMain Device Repeat Settings Change Partition SettingAuto-Expire on Specified Date Recording Data Readout SettingPlayback Device Repeat Setting Image Originality Check PlayDeleting the data of the DVD takes about 30 or 40 minutes Data ClearMain Storage Memory Copy 1/CopyCascade Other convenient functionsTo control the other recorder, repeat steps 1 and 2 above Various playback functions Triplex playback Playback the latest recorded contentsChanging playback intervals Simultaneous playback during recordingRegistering a book mark Registering the picturePicture copy System Log List. See Functions of the unit in case of power failurePower failure compensation circuit Power failure reset recordingOperation example Operation examplesRepeat recording settings see Performs alarm recording at the specified recording rateSettings Alarm area settings see Set the normal and alarm recording areasSet the motion detection settings for Motion B Motion detection settings see pages 58Set the timer program number to Program Timer recording settings see pages 56Set the motion detection settings for Motion a and Motion B Active Monday Friday Split screen buttons Basic operationsBasic multiplexer functions Digital Zoom buttonBasic manual recording To stop playback, press the Stop button Basic playbackRepeatedly. See To change the playback deviceSearch by Time and Date Basic search100 Search by Alarm ListCommunications by Web Browser LoginCommunications by Web Browser 101Main Menu 102Live Monitoring 103Select the date and time and click Search 104Playback Time SearchImage Search Alarm List SearchConfiguration Menu 105If you have selected cancel When you have selected cancel106 Select change and left-click Mail Setup107 Recorder Title & Camera Titles108 NAS SetupSelect NAS Setup and left-click Clock SetupClose the Web Browser Change Login User109 LogoutWithout audio recording Recording time table110 Continuous recording time table111 112 TroubleshootingOthers 113Countermeasure Log number output 114Call OUT 115116 Setup Menu 200 000Recording Set Recording Pattern a Normal/Timer Check sheetCheck sheet 117118 Set Recording Pattern B Timer119 120 Set Recording Pattern C Timer121 122 Set Recording Pattern D Timer123 124 Emergency Recording SetupAudio Recording Setup Timer Configure Timer ProgramMotion Det Default125 Define HolidaysSystem Menu Language Selection Rear Terminal SettingPassword Setting 126Sequence Multi Multiplexer SettingOutput a Settings 127128 Output B SettingsAlarm Display Setting Output Setting Alarm Display Setting Output aCovert Camera Setting Alarm Display Setting Output B129 Audio Setting On Screen Display Setting130 System Menu 300 000 131Device ID PTZ Setting PTZ Camera Configuration132 Port PanMemory Add/Remove HDD Device 133134 Select using for Copy1 or Copy2Add/Remove DVD/CD Drive Recording Data Readout Setting Data Management Setting for Main Memory135 136 GlossaryGlossary Glossary 137Specifications Specifications138 872C355B2
Related manuals
Manual 40 pages 7.44 Kb Manual 8 pages 45.69 Kb