JVC DR-M1SLB, LPT0827-001B manual Programme Recording, Select the L-2 Select mode, REC Mode

Page 65

65

Automatic Satellite

Programme

Recording

This function allows you to automatically record a satellite programme which is timer-programmed on your external satellite receiver. Connect a satellite receiver to the unit’s L-2 IN/DECODER connector and programme the timer on the satellite receiver. When the signals come into the unit from the satellite receiver, the unit automatically turns on and starts recording.

ATTENTION:

Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the unit will start recording when the satellite receiver’s power is turned on.

If you have connected another appliance other than a satellite receiver to the L-2 IN/DECODER connector, be sure not to engage the Automatic Satellite Programme Recording mode; otherwise, the unit will start recording when the connected appliance’s power is turned on.

Automatic Satellite Programme Recording and timer-recording cannot be done at the same time.

Before performing the following steps:

Make sure the satellite receiver is connected to the unit’s L-2 IN/DECODER connector. ( pg. 90)

Programme the timer on the satellite receiver.

Slide the TV/CABLE/SAT/DVD switch to TV.

A Select the L-2 SELECT mode.

Set “L-2 SELECT” to “SAT VIDEO” or “SAT S-VIDEO” ( pg. 85, “L-2 Select Setting (L-2 SELECT)”).

Also refer to “IMPORTANT” on page 90.

B

Press

C

Set the recording speed.

REC MODE.

Engage the Automatic Satellite Programme Recording mode.

Press and hold SAT# for about 2 seconds. “SAT#” appears on the front display panel and the unit turns off automatically.

NOTES:

To disengage the Automatic Satellite Programme Recording mode, press SAT#.

If the unit’s power is off, it is not possible to engage the Automatic Satellite Programme Recording mode.

In step C, if “SAT#” blinks quickly on the front display panel even though your satellite receiver’s power is off, Automatic Satellite

Programme Recording will not work properly with that satellite receiver*. If this is the case, perform “Manual Timer Programming” ( pg. 58) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Automatic Satellite Programme Recording is not possible with those satellite receivers.

“SAT#” blinks on the front display panel while Automatic Satellite Programme Recording is in progress.

For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

Automatic Satellite Programme Recording is not possible if your satellite receiver does not have a timer.

Pressing the unit’s 1 button while Automatic Satellite Programme Recording is in progress turns off the unit’s power and disengages the Automatic Satellite Programme Recording mode.

If there are more than one satellite programmes you wish to record with Automatic Satellite Programme Recording, it is not possible to set different recording speeds for each programme.

Depending on the type of satellite receiver, the unit may not record a slight portion of the beginning of the programme or may record slightly longer than the actual length of the programme.

If you engage the Automatic Satellite Programme Recording mode when the satellite receiver’s power is on, the unit will not start Automatic Satellite Programme Recording even though “SAT#” blinks on the front display panel. When the satellite receiver shuts off once and is turned back on again, the unit starts recording.

You can also record a programme from your cable system in the same way if the system has a timer.

Just Clock ( pg. 104) does not work when the Automatic Satellite Programme Recording mode is engaged.

When the Automatic Satellite Programme Recording mode is engaged, or the unit’s power is turned off after Automatic Satellite Programme Recording is finished, the unit will not enter the Timer mode even though “AUTO TIMER” is set to “ON” ( pg. 96).

Image 65
Contents DR-M1SLB Safety Precautions Moisture Condensation Above ALL Some Do’s And Don’ts On The Safe Use Of EquipmentContents Recordable/playable discs About DiscsDVD-RAM Discs DVD-R/RW DiscsUnplayable Discs Discs for Playback OnlyRegion Number Audio CDFile Structure of Discs Recording Medium and FormatDVD-RAM DVD-RMarks related to video DVD Video MarksJPEG/MP3 Disc CD-R/RW/ROM Care and Handling of Discs Placing a DiscFront View Digital Audio OUT COAXIAL/OPTICAL Rear ViewFront Display Panel Disc Type/Status IndicatorSimulated Surround Effect Indicator 3D  pg Disc Display ON-SCREEN DisplayHow To Use Remote ControlCheck Contents Connect the unit to mains Install the unitConnect the unit to a TV Back of unit After the connection is completed, perform Auto Set Up onConnect the unit to TV 8To connect to TV’s component video input connectorsPerform Auto Set Up Auto Set UpTurn on the unit EnterAfter Auto Set Up is completed, perform Monitor Set on Initial SettingsAfter Preset Download is completed, perform Monitor Set on Perform Preset DownloadPress Enter Press rt to move Arrow to T-V Link and press EnterJust Clock InformationAccess the Video IN/OUT screen Access the Main Menu screenComplete the setting Monitor SetPress w e to move Arrow to DVD SET UP, then press OK Access the Language SET screenLanguage Select the desired languageLanguage Code List Install a Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connectionsAccess the SAT/GUIDE PR screen Setting satellite receiver’s brand and channelSelect the satellite receiver’s channel for testing Turn on the satellite receiverCheck the result of the test TV Auto Power OnUnit Auto Standby Direct Rec Load a disc Basic PlaybackStart playback Pause playbackAccess the DVD menu Locating a desired scene using the DVD menuTop menu Disc menuHigh-Speed Search Locating the start point of the item or skip the itemSlow Motion Skip SearchMemorise a resume point Resume FunctionResume playback Mark positionsSubtitle Selection Switching Time IndicationAngle Selection Access the PBC menu Locating a desired scene usingWhen you can’t switch the audio channel of a Audio Channel Selection Menu of a Video CD with PBCSuperimpose display Live Memory PlaybackImage figure of DVD-RAM disc Recording screen Overview of Live Memory PlaybackRecording stops Live Memory Playback screen CheckingExample of bar meter display Display during Live Memory PlaybackLive Check Available only when pausedFunctions To watch a programme previously recorded while recording Start Live Memory PlaybackStart One Touch Replay function How to Access Play Set Up Menu Using Play Set Up MenuContents of Play Set Up Menu during playback Before using Play Set Up MenuSelect the option Access Play Set Up MenuSelect the menu item Repeat Playback Select the repeat modeLocate the start point Locate the end point and start A-B Repeat PlaybackProgramme Playback Random PlaybackSelect the tracks in the desired order While stoppedSpecify the number of the selected item Locating the beginning of a desired selectionSelect the desired item Enter the time To cancel the simulated surround effectUse number keys 1-9, 0 to enter the time, then press Press Enter to clear 3D-ON from the screenSetting the progressive mode Adjusting the picture qualitySelect the switching interval of the slide show Enter your password Access the DVD SET UP screenParental Lock Select the desired levelAccess the password screen To change the settingsChange the level Change the country codeCountry/Area Code List for Parental Lock Playback Operations Start recording Set the recording speedPause recording Stop recordingEngage the ITR mode Instant Timer Recording ITRSwitch the TV to TV mode Set the recording durationReceiving Stereo and Bilingual Programmes Free Rate FunctionType of Broadcast Being ReceivedBefore performing the Video Plus+ Timer Programming Access the Video Plus+ screenEnter the PlusCode number Check the programme dataComplete timer programming Access the confirmation screenEngage the unit’s timer mode Set the following recording options as requiredAccess Programme Check screen Manual Timer ProgrammingAccess the programme screen Enter the recording datePDC Recording Refer to step E in Video Plus+ Timer Programming  pgEnter the recording stop time Enter the channel positionBefore performing On-Disc Timer Programming On-Disc Timer ProgrammingLoad the disc Set DAILY/WEEKLY optionHow discs are overwritten Complete timer correction Disengage the timer modeChange a programme Programme’s information on the front display panelChange the programme setting Select the desired programme to be cancelled or changedConfirm the overlapping programmes Check if the conflict has been settledEngage the Automatic Satellite Programme Recording mode Select the L-2 Select modeREC Mode Programme RecordingIcons and their meanings Arrow Guidance for operations H Operational commandsIcons Limitations of registration About registration of informationAbout editing of programmes Press ENTER. Or simply press 4. The playback starts Access the Index screenSelect the programmes Modify Index Access the modify screenSelect a programme Register new indexProtect title Modify Programme NameModify Category Delete programme Access the delete screenDelete unwanted part of the programme Confirm the deletionCreate Play List Access the Play List screenCreate a play list Confirm the play listAdd scenes to a play list Access the Editing screenMove scenes Confirm the additionRepeat steps C E Confirm the moveDelete play list Play back play listModify Programme Title Select the play listsSort the information Access the library screenScan for Programme from library Delete information Register discRegister the disc Confirm the registrationPlayback with MP3/JPEG Navigation Select the group Display the itemSelect the item Select the items in the desired orderDV Dubbing Prepare the unit for dubbing Performing dubbing without using the DV Dubbing controllerStart dubbing Stop dubbingSet the unit’s input mode Engage the Play mode of the source player Set the input mode of recording deckEngage the Record mode of the recording deck Start the source playerIN/OUT connector Access the Output/Input Set screen1 Output 1 InputSelect the input mode for the L-2 Decoder connector Input Setting F-1 InputSelect the input mode for the Video Video connector 2 SelectPlace a disc and load an MD Select the input modeFor the unit For the digital audio deviceRemote 1/2/3/4 Code Switching Operate the TV TV Multi-Brand Remote ControlSet the TV brand code Slide the TV/CABLE/SAT/DVD switch to CABLE/SAT Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Operate the satellite receiverConnecting To a Satellite Receiver Make connections Access the Recording SET screen Mode SetDVD SET UP Function SET UPDigital Audio OUT Audio OutputAnalog Audio OUT Range ControlRecording SET XP Mode REC AudioSave AS Library Audio RECDisplay SET Power SaveSuperimpose Grey BackOFF on Auto TimerOthers Guide Program Number Set Video Plus+ System SetupGuide Program Number Enter the Guide Program numberAuto Channel Set Tuner SetPerform Auto Channel Set View the Confirmation screenPress w e to select Manual CH SET, then press Manual Channel SetSelect the channel position Change Station Channel Position 100Delete a Channel Set Stations B 101Set Stations a TV Station And ID List 102TV Station Channel Number Guide 103Press w e to select Initial SET UP, then press Enter Access the Clock SET screenClock Set 104Set Just Clock 105Set the source channel position for clock data Start the clock operation106 Format a discFormat a DVD-RAM disc Format a DVD-RW discFinalise a disc Cancel the finalisation of a DVD-RWdisc107 Finalise a DVD-R/RW discSet the scan mode Scan Mode Set108 Press Progressive Scan for 2 or more secondsGeneral 109Recording 110ON-SCREEN Messages 111ON-SCREEN Messages 112DTS 113Jpeg MpegAccessories TUNER/TIMER114 GeneralAuto Channel Set 115Delete programme Disc menu Discs for Playback Only Subtitle Selection Time Search Top menuDR-M1SLB