JVC DR-M1SLB manual Audio Output, Digital Audio OUT, Analog Audio OUT, Range Control, Output Level

Page 93

93

AUDIO OUTPUT

(The boldface settings in the table below indicate the settings at your purchase.)

8 DIGITAL AUDIO OUT

Set to the appropriate mode according to the type of the device connected to

DOLBY DIGITAL/PCM

DIGITAL AUDIO OUT connector.

STREAM/PCM

DOLBY DIGITAL/PCM:

PCM ONLY

Select this when you connect the digital input connector of a Dolby

 

Digital decoder or an amplifier with a built-in Dolby Digital

 

decoder.

 

STREAM/PCM:

 

Select this when you connect the digital input connector of an

 

amplifier with a built-in DTS, Dolby Digital, or MPEG multichannel

 

decoder.

 

PCM ONLY:

 

Select this when you connect the linear PCM digital input of other

 

audio equipment (amplifier, MD or DAT deck, etc.).

 

 

8 ANALOG AUDIO OUT

Select the appropriate setting to accommodate the unit to the connected A/V

STEREO

equipment. This function takes effect when a DVD VIDEO disc is played back.

DOLBY SURROUND

STEREO:

 

Select this when listening to conventional two-channel stereo audio

 

with the unit’s AUDIO OUT connectors connected to a stereo

 

amplifier/receiver or TV set, or in case you want to record the audio

 

from a DVD VIDEO disc to a Mini Disc, etc.

 

DOLBY SURROUND:

 

Select this when listening to multichannel surround audio with the

 

unit’s AUDIO OUT connectors connected to an amplifier/receiver

 

with a built-in surround decoder or a surround decoder.

 

 

8 D. RANGE CONTROL

The dynamic range (the difference between the loudest sound and the quietest

NORMAL

one) can be compressed during playback of a programme encoded in Dolby

WIDE RANGE

Digital format.

TV MODE

This function takes effect when a DVD VIDEO disc recorded in Dolby Digital

 

format is played back at low or middle volume.

 

NORMAL:

 

Normally select this setting to activate this function.

 

WIDE RANGE:

 

Select this to deactivate this function when you enjoy wide dynamic

 

range programme.

 

TV MODE:

 

Select this when you hear the sound through the TV’s speaker(s).

 

NOTES:

 

● This function takes no effect on programmes other than that recorded in Dolby Digital

 

format.

 

● This function dose not work when Simulated Surround Effect is activated. ( pg. 47)

 

● The effect of “NORMAL” and “WIDE RANGE” may not be different depending on discs.

 

 

8 OUTPUT LEVEL

You can lower the output level of analog audio to accommodate the unit to the

STANDARD

connected A/V equipment.

LOW

STANDARD:

 

Normally select this setting.

 

LOW:

 

The output level of analog audio is lowered.

 

 

Page 92 Page 94
Image 93
Page 92 Page 94
Contents DR-M1SLB Safety Precautions Moisture Condensation Above ALL Some Do’s And Don’ts On The Safe Use Of EquipmentContents Recordable/playable discs About DiscsDVD-RAM Discs DVD-R/RW DiscsUnplayable Discs Discs for Playback OnlyRegion Number Audio CDFile Structure of Discs Recording Medium and FormatDVD-RAM DVD-RDVD Video Marks JPEG/MP3 Disc CD-R/RW/ROMMarks related to video Care and Handling of Discs Placing a DiscFront View Digital Audio OUT COAXIAL/OPTICAL Rear ViewFront Display Panel Disc Type/Status IndicatorSimulated Surround Effect Indicator 3D  pg Disc Display ON-SCREEN DisplayHow To Use Remote ControlCheck Contents Install the unit Connect the unit to a TVConnect the unit to mains Back of unit After the connection is completed, perform Auto Set Up onConnect the unit to TV 8To connect to TV’s component video input connectorsPerform Auto Set Up Auto Set UpTurn on the unit EnterAfter Auto Set Up is completed, perform Monitor Set on Initial SettingsAfter Preset Download is completed, perform Monitor Set on Perform Preset DownloadPress Enter Press rt to move Arrow to T-V Link and press EnterJust Clock InformationAccess the Video IN/OUT screen Access the Main Menu screenComplete the setting Monitor SetPress w e to move Arrow to DVD SET UP, then press OK Access the Language SET screenLanguage Select the desired languageLanguage Code List Install a Satellite Controller Installing Satellite ControllerAttach the Satellite Controller Make connectionsAccess the SAT/GUIDE PR screen Setting satellite receiver’s brand and channelSelect the satellite receiver’s channel for testing Turn on the satellite receiverTV Auto Power On Unit Auto Standby Direct RecCheck the result of the test Load a disc Basic PlaybackStart playback Pause playbackAccess the DVD menu Locating a desired scene using the DVD menuTop menu Disc menuHigh-Speed Search Locating the start point of the item or skip the itemSlow Motion Skip SearchMemorise a resume point Resume FunctionResume playback Mark positionsSwitching Time Indication Angle SelectionSubtitle Selection Access the PBC menu Locating a desired scene usingWhen you can’t switch the audio channel of a Audio Channel Selection Menu of a Video CD with PBCLive Memory Playback Image figure of DVD-RAM discSuperimpose display Recording screen Overview of Live Memory PlaybackRecording stops Live Memory Playback screen CheckingExample of bar meter display Display during Live Memory PlaybackAvailable only when paused FunctionsLive Check Start Live Memory Playback Start One Touch Replay functionTo watch a programme previously recorded while recording How to Access Play Set Up Menu Using Play Set Up MenuContents of Play Set Up Menu during playback Before using Play Set Up MenuAccess Play Set Up Menu Select the menu itemSelect the option Repeat Playback Select the repeat modeLocate the start point Locate the end point and start A-B Repeat PlaybackProgramme Playback Random PlaybackSelect the tracks in the desired order While stoppedLocating the beginning of a desired selection Select the desired itemSpecify the number of the selected item Enter the time To cancel the simulated surround effectUse number keys 1-9, 0 to enter the time, then press Press Enter to clear 3D-ON from the screenAdjusting the picture quality Select the switching interval of the slide showSetting the progressive mode Enter your password Access the DVD SET UP screenParental Lock Select the desired levelAccess the password screen To change the settingsChange the level Change the country codeCountry/Area Code List for Parental Lock Playback Operations Start recording Set the recording speedPause recording Stop recordingEngage the ITR mode Instant Timer Recording ITRSwitch the TV to TV mode Set the recording durationReceiving Stereo and Bilingual Programmes Free Rate FunctionType of Broadcast Being ReceivedBefore performing the Video Plus+ Timer Programming Access the Video Plus+ screenEnter the PlusCode number Check the programme dataComplete timer programming Access the confirmation screenEngage the unit’s timer mode Set the following recording options as requiredAccess Programme Check screen Manual Timer ProgrammingAccess the programme screen Enter the recording datePDC Recording Refer to step E in Video Plus+ Timer Programming  pgEnter the recording stop time Enter the channel positionBefore performing On-Disc Timer Programming On-Disc Timer ProgrammingLoad the disc Set DAILY/WEEKLY optionHow discs are overwritten Complete timer correction Disengage the timer modeChange a programme Programme’s information on the front display panelChange the programme setting Select the desired programme to be cancelled or changedConfirm the overlapping programmes Check if the conflict has been settledEngage the Automatic Satellite Programme Recording mode Select the L-2 Select modeREC Mode Programme RecordingArrow Guidance for operations H Operational commands IconsIcons and their meanings About registration of information About editing of programmesLimitations of registration Access the Index screen Select the programmesPress ENTER. Or simply press 4. The playback starts Modify Index Access the modify screenSelect a programme Register new indexModify Programme Name Modify CategoryProtect title Delete programme Access the delete screenDelete unwanted part of the programme Confirm the deletionCreate Play List Access the Play List screenCreate a play list Confirm the play listAdd scenes to a play list Access the Editing screenMove scenes Confirm the additionRepeat steps C E Confirm the moveDelete play list Play back play listModify Programme Title Select the play listsAccess the library screen Scan for Programme from librarySort the information Delete information Register discRegister the disc Confirm the registrationPlayback with MP3/JPEG Navigation Select the group Display the itemSelect the item Select the items in the desired orderDV Dubbing Prepare the unit for dubbing Performing dubbing without using the DV Dubbing controllerStart dubbing Stop dubbingSet the unit’s input mode Engage the Play mode of the source player Set the input mode of recording deckEngage the Record mode of the recording deck Start the source playerIN/OUT connector Access the Output/Input Set screen1 Output 1 InputSelect the input mode for the L-2 Decoder connector Input Setting F-1 InputSelect the input mode for the Video Video connector 2 SelectPlace a disc and load an MD Select the input modeFor the unit For the digital audio deviceRemote 1/2/3/4 Code Switching TV Multi-Brand Remote Control Set the TV brand codeOperate the TV Slide the TV/CABLE/SAT/DVD switch to CABLE/SAT Satellite Receiver Multi-Brand Remote ControlSet the satellite receiver brand code Operate the satellite receiverConnecting To a Satellite Receiver Make connections Access the Recording SET screen Mode SetDVD SET UP Function SET UPDigital Audio OUT Audio OutputAnalog Audio OUT Range ControlRecording SET XP Mode REC AudioSave AS Library Audio RECDisplay SET Power SaveSuperimpose Grey BackAuto Timer OthersOFF on Guide Program Number Set Video Plus+ System SetupGuide Program Number Enter the Guide Program numberAuto Channel Set Tuner SetPerform Auto Channel Set View the Confirmation screenManual Channel Set Select the channel positionPress w e to select Manual CH SET, then press 100 Delete a ChannelChange Station Channel Position 101 Set Stations aSet Stations B TV Station And ID List 102TV Station Channel Number Guide 103Press w e to select Initial SET UP, then press Enter Access the Clock SET screenClock Set 104Set Just Clock 105Set the source channel position for clock data Start the clock operation106 Format a discFormat a DVD-RAM disc Format a DVD-RW discFinalise a disc Cancel the finalisation of a DVD-RWdisc107 Finalise a DVD-R/RW discSet the scan mode Scan Mode Set108 Press Progressive Scan for 2 or more secondsGeneral 109Recording 110ON-SCREEN Messages 111ON-SCREEN Messages 112DTS 113Jpeg MpegAccessories TUNER/TIMER114 GeneralAuto Channel Set 115Delete programme Disc menu Discs for Playback Only Subtitle Selection Time Search Top menuDR-M1SLB
Top Page Image Contents