JVC DR-MV5SEK, DR-MV5BEK manual On The Front Display Panel, Link Functions DVD Deck Only

Filename [MV5SEK_05Name.fm]
MV5SEK_00.book Page 19 Wednesday, August 31, 2005 7:58 PM	Masterpage:Right+
	INITIAL SETTINGS EN 19

Results Of Auto Set Up/Preset Download Appearing	INFORMATION
On The Front Display Panel	Just Clock
	Your unit is equipped with the Just Clock function which provides
If both Auto Channel Set and	accurate time keeping through automatic adjustments at regular
	intervals, by reading data from a PDC signal. If you want to take
Auto Clock Set have been
	advantage of this function, simply set it to “ON”. ( pg. 88)
performed successfully, the
correct current time is displayed.
	If you have any difficulty with the above procedures call the JVC
Turn on the TV and select its AV mode, then make sure that all
	Customer Service Hot Line on 0870 330 5000.
necessary stations have been stored in the unit’s memory by using
the PR +/– button(s).	T-V Link Functions (DVD Deck Only)
● If station names (ID –  pg. 97) have also been stored in the unit’s
memory, the station name will be displayed at the top right corner of
	When you connect the unit to your TV via a fully-wired 21-pin
the TV screen for about 5 seconds when the unit is tuned to a
	SCART cable ( pg. 15), the following functions are available. You
different station.
	can use these functions only with a TV offering T-V Link, etc.*
● If you want to set the tuner manually such as to add or skip channels,
	For details, refer to the instruction manual of your TV.
to change channel positions, or to set or change station names, see
pages 85 – 87.	* Compatible with TVs offering T-V Link, EasyLink, Megalogic,
If Auto Channel Set has	SMARTLINK, Q-Link or DATA LOGIC via a fully-wired 21-pin SCART
	cable. The degree of compatibility and available functions may differ by
succeeded but Auto Clock Set	system.
has not, “PR 1” (channel	TV Auto Power On
position) is displayed.
	The TV will turn on and be set to its AV mode automatically
OR
If both Auto Channel Set and Auto Clock Set have failed,	whenever you start playback.
“– –:– –” is displayed.	For details, refer to the instruction manual of your TV.
A Turn on the TV and select its AV mode, then make sure that all	Unit Auto Standby
necessary stations have been stored in the unit’s memory by using	You can use your TV’s remote control to turn off the unit.
the PR +/– button(s).	For details, refer to the instruction manual of your TV.
● If station names (ID –  pg. 97) have also been stored in the unit’s	Direct Rec
memory, the station name will be displayed at the top right corner of
	You can easily start recording the programme that you are
the TV screen for about 5 seconds when the unit is tuned to a
	watching on your TV. When you use this function, set “DIRECT
different station.
	REC” to “ON”. ( pg. 79)
● If you want to set the tuner manually such as to add or skip channels,
to change channel positions, or to set or change station names, see
pages 85 – 87.

BPerform “Clock Set” on page 88.

ATTENTION:

After making sure the cables are connected properly, turn off the unit’s power once, then turn the unit’s power back on again.

Perform “Auto Set Up” on page 17 or “Preset Download” on page 18 again.

IMPORTANT:

●To check if the Guide Program numbers have been set correctly, perform the VIDEO Plus+ Timer Programming. ( pg. 29)

●In certain reception conditions, station names may not be stored correctly, and auto Guide Program Number Set may not work properly. If the Guide Program numbers are not set properly when you timer-record a TV programme using the VIDEO Plus+ system, the unit will record a TV programme of a different station. When programming the timer using the VIDEO Plus+ system, be sure to check the desired channel is selected correctly. ( pg. 29)

●Your unit memorises all detected stations even if reception of some of them is poor. You can delete those stations with an unacceptable picture. ( pg. 86, “Delete A Channel”)

Page 19

Wednesday, 31 August 2005 19:58