JVC DR-MV5SEK, DR-MV5BEK manual Timer Recording VHS Deck, Other Problems, For composite connection

Page 93

Filename [MV5SEK_13Subsidiary.fm]

 

MV5SEK_00.book Page 93 Wednesday, August 31, 2005 7:58 PM

Masterpage:Right+

 

TROUBLESHOOTING EN 93

Automatic Satellite Programme Recording does not start.

The satellite receiver is not connected properly to this unit. ]Connect the satellite receiver to the [L-2 IN/DECODER]

connector properly. ( pg. 76)

On the front display panel, “– –:– –” appears.

Power failure occurred.

]Set date and time correctly. ( pg. 88)

“PROGRAMME FULL” appears on the TV screen during timer programming.

8 programmes have already been timer programmed. ]Clear unnecessary programmes on the unit, then try timer

programming again. ( pg. 34)

The disc space does not increase when recorded titles are cleared.

The PC’s data recorded on a DVD-RAM drive cannot be cleared

on this unit.

]Format the disc. (When the disc is soiled, wipe the disc with a soft dry cloth before formatting.) ( pg. 9, 89)

Timer Recording (VHS Deck)

“NO TAPE” appears on the front display panel.

No tape is loaded.

]Press TIMER # so that the VHS timer indicator lights off. Load a cassette with the record safety tab intact, then press TIMER # again.

Timer programming cannot be made.

Date and time is not correct.

]Set date and time correctly. ( pg. 88)

The timer is not engaged.

]Press TIMER # and confirm that the VHS timer indicator lights up on the front panel display.

Timer recording is in progress.

]Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

Timer programming recording does not start.

Date and time is not correct.

]Set date and time correctly. ( pg. 88)

The timer is not engaged.

Press TIMER # and confirm that the VHS timer indicator lights up on the front panel display.

The VHS timer indicator on the front display panel won’t stop blinking.

The timer is engaged but there’s no cassette loaded. ]Load a cassette with the record safety tab intact.

The loaded cassette has had its record safety tab removed. ]Remove the cassette and cover the hole with adhesive tape, or

insert a cassette with the record safety tab intact.

The tape is automatically stopped and “[’’ and the VHS timer indicator on the front display panel won’t stop blinking.

The end of the tape was reached during timer recording. ]The programme may not have been recorded in its

entirety. Next time make sure you have enough time on the tape to record the entire programme.

The end of the tape was reached during Instant Timer

Recording.

]The program may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire program.

VIDEO Plus+ Timer Programming cannot be made.

Date and time set on the unit is not correct. ]Set date and time correctly. ( pg. 88)

The channel position does not correspond to that in the receiving area.

]Set the correct channel position for the receiving broadcast. ( pg. 85)

The VIDEO Plus+ system does not timer-record properly.

The unit’s channel positions have been set incorrectly. ]Refer to “VIDEO Plus+ System Setup” ( pg. 83) and

reperform the procedure.

Other Problems

The image of the TV broadcast appears distorted on the TV screen.

For composite connection

]Press PROGRESSIVE SCAN for 3 or more seconds so that the Video output indicator ( ) lights off on the front display panel.

For component video connection

]Press PROGRESSIVE SCAN for 3 or more seconds so that the Video output indicator ( ) lights up on the front display panel.

When scanning channels, some of them are skipped over.

Those channels have been designated to be skipped.

]If you need the skipped channels, restore them. ( pg. 85)

The channel cannot be changed.

Recording is in progress.

]Press 9 to pause the recording, change channels, then press 4 to resume recording.

Channel settings that were made manually seem to have changed or disappeared.

After the manual settings were made, Auto Channel Set was

performed.

]Perform “Manual Channel Set” ( pg. 85).

Malfunction occurs and the unit cannot be power off.

]Reset the unit by disconnecting the AC power plug from the AC outlet and connect again.

Page 93Wednesday, 31 August 2005 19:58

Image 93
Contents DR-MV5SEK DR-MV5BEK Do not place the unit Filename MV5SEK02Safety.fmDo not block the unit’s ventilation openings or holes To mobile phone usersEquipment Check ContentsFilename MV5SEK03Contents.fm Enjoy the vivid picture quality DVD recording/playbackMasterpageRight0 Contents Recordable/Playable Discs About DiscsDiscs For Playback Only DVD-RAM DiscsUnplayable Discs Recording Medium And FormatFile Structure Of Discs Region NumberAudio CD/Video CD/Super Video CD Svcd DVD Video MarksJPEG/MP3 Disc CD-R/RW/ROM Marks related to videoCare And Handling Of Discs Placing a DiscFront View Rear ViewFilename MV5SEK05Name.fm Remote Control How To Use pg On-Screen Display DVD deck On-Screen Display VHS deck VPS/PDC Indicator*  pgC D EFG H I J K L M N Front Display PanelConnections Composite ConnectionLuminance brightness Component Video Connection DVD deck only Enter SET UP Auto Set UpNumber Set VHS DVDPreset Download Cable  pg , the unit will automatically perform PresetDownload instead of the Auto Set Up in on page 17. After Link Functions DVD Deck Only On The Front Display PanelLanguage Monitor Set DVD Deck Only VHS DVD Enter SET UPPan&Scan/Letter Box Pan&ScanFilename MV5SEK06TocOperation.fm PlaybackWant to do? Basic Playback DVD Filename MV5SEK07Basic PlayRec.fmTo play back an MP3/JPEG disc, see Playback With MP3 Compact VHS camcorder recordings can be played on this Basic Playback VHSLoad a recordable disc Basic Recording DVDMode Approx Time approx Recording Resume FunctionRecording Recording amount Basic Recording VHS Maximum Recording Use Mode Time ApproxVHS DVD Cancel Enter ReturnSatellite Receiver Users DVD Deck Only PDC Recording Weekly/Daily RecordingManual Timer Programming DVD TimerVHS On-Disc Timer Programming DVD Deck OnlySatellite Receiver Users How Discs Are Overwritten To cancel the programme Check, Cancel And Change ProgrammesSAT For Automatic Satellite Programme RecordingCancel Prog Enter When Programmes Overlap Each OtherPress Cancel To change the programme settingRecording DVD Deck Only REC ModeStop and pause mode on the DVD deck Auto Recording Mode OptimizerTo DVD Auto Title Creation DubbingVHS/DVD VHS Dubbing Dubbing a Part Of a CassetteREC Mode Progressive Scan Dubbing An Entire DiscVHS/DVD Dubbing Enter REC Mode DV Dubbing DVD Deck Only Performing dubbing without using the DV Dubbing controllerIf the camcorder has no S-VIDEO output connector Edit From a CamcorderPanel When using your unit as the recording deck When using your unit as the source playerOutput/Input Set Output And L-1 Input SettingInput Setting Select SettingExample Dubbing to an MD Digital Audio DubbingAdvanced Playback DVD High-Speed SearchDVD TOP Menu Enter Still Picture/Frame-By-Frame Playback Resume FunctionSlow Motion Skip SearchSubtitle Selection Checking The Time Information Angle SelectionSelection display appears Audio Channel SelectionPress Audio or w e to select Your desired audio language SoundDisplay Recording/Playback Status DisplayRecording screen Overview Of Live Memory PlaybackDisplay During Live Memory Playback To Watch a Programme Previously Recorded While Recording Available only when pausedHow To Access The On-screen Bar Using The On-screen BarBasic Operation On The On-screen Bar Enter NavigationRepeat Playback Locating The Beginning Of a Desired SelectionEnter On Screen Clear Setting The Progressive Mode Adjusting The Picture QualityTime Search To select track 5, press the number buttonCancel Enter Select The Switching Interval Of The Slide ShowRandom Playback Programme PlaybackAdvanced Playback VHS Clean the video heads using a dry cleaning cassette whenIndex Search During playback, press 5 for forward high-speed search, orManual Tracking Next Function MemoryVHS Progressive Scan Soundtrack SelectionAdvanced Recording DVD Instant Timer Recording ITRElapsed Recording Time And Disc Remaining Time Indication DVD TV/VIDEOSelect FR Just in a recording mode selection procedure Free Rate FunctionSelection Of The Audio Channel To Be Recorded On a Disc Elapsed Recording Time Indication Advanced Recording VHSAccidental erasure prevention Watch Another Programme While Recording On The UnitTo Record Stereo and Bilingual Programmes A2 Tape Remaining TimeTo Record Nicam Stereo and Bilingual Programmes PlaybackLibrary Database DVD Navi Display for original Display for play list RecordingIcons and their meanings Scan For Beginning Of Title Modify IndexMemo Enter Navigation Protect Title DVD-RAM/DVD-RW VR mode Delete Unwanted Part Of The Title DVD-RAM/DVD- RW VR modeModify Title Name Modify CategoryAdd Scenes To a Play List Modify Play List InformationCreate Play List MemoSCENE, then press Enter Move ScenesDelete Play List Play Back Play ListModify Play List Name Press 8 to stop playbackScan For Title From Library Modify Library InformationRegister Disc Delete InformationFor MP3 Playback Locating The Desired Group And TracksFor Jpeg Playback On completion of the playback of all the itemsTips for your trouble Specifications Remote control settingFor better sound For DVD operations For VHS operations FormatRemote Control 1/2/3/4 Code Switching Remote Control FunctionsBrand Name Code TV Multi-Brand Remote ControlConnecting To a Satellite Receiver Connecting/Using a Decoder DVD Deck OnlyProgramme When you can’t switch the audio channel of a bilingualDVD Digital Audio OUT Dolby Digital / PCM / Stream Mode Set DVD DeckRecording SET OFF You cannot use the resume function Scan Mode SetMode Set VHS Deck VHS EnterThen press Enter Press rt to select the desired Tray Lock DVD Deck Only SP mode LP modeFor Example To lock trayVideo Plus+ System Setup Guide Program Number SetGuide Program Number Press w e to select Initial SET UP, then press t VHS Enter SET UPTuner Set Auto Channel SetPress rt to input the channel Press SET UP to close the Confirmation screenNumber you want to store Press Enter to enter new channel information.Delete a Channel Press SET UP twice to close the Confirmation screenChange Station Channel Position Press rt w e to select the new channel position, then pressPress SET UP three times to close the Confirmation screen Fine-Tuning Channels Already StoredSet Stations a Set Stations BJust Clock Clock SetFormat a DVD-RAM Disc Format a Disc DVD Deck OnlyFormat a DVD-RW Disc Then press tAfter finalising For DVD-R/RW Video mode discs Cancel The Finalisation Of a DVD-RW DiscFinalise a DVD-R/RW Disc DVD EnterPlayback DVD Deck Initialising DVD Deck OnlyGeneral Playback VHS Deck Timer Recording DVD DeckRecording DVD Deck Recording VHS DeckOther Problems Timer Recording VHS DeckFor composite connection For component video connectionTimer recording has finished during Live Memory playback An invalid PlusCode number has been input.  pgDuring Live Memory playback, 8 has been pressed.  pg Power consumption Power requirementTemperature Dimensions WxHxDLanguage Code List TV Station And ID List TV Station Channel Number Guide Audio Language/Sound Selection When Programmes Overlap Each OtherPlayback Control PBC Function Elapsed Recording Time And Disc Remaining Time100Wednesday, 31 August 2005 Filename MV5SEK15Cov4.fm