LG Electronics HCS6300 setup guide For Customer Support/Service, please call­1-888-865-3026

Page 2

For Customer Support/Service, please call:­1-888-865-3026

The latest product information and documentation is available online at:

www.LGsolutions.com/products

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL. ALL CARDS MUST BE INSERTED AND REMOVED BY QUALIFIED SERVICE PERSONNEL ONLY.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

L’appareil ne doit pas être exposé à des égouttements d’eau ou des éclaboussures et de plus qu’aucun objet rempli de liquide tel que des vases ne doit être placé sur l’appareil.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial envi- ronment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user should be required to correct the interference at his own expense.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.

NOTE TO SATELLITE DISH INSTALLER:

This reminder is provided to call your attention to Articles 810 and 820 of the 2002 National Electrical Code. Refer to Article 810, in particular 810-1 and 810-15, for required grounding of the metal dish antenna. Refer also to the 810-2 which, by reference to Article 820, requires that the satellite dish coaxial cable shield be connected to the grounding system of the building as close to the point of cable entry as practical.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc.

2000 Millbrook Drive, Lincolnshire, IL 60069, USA • Phone: 1-847-941-8000

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.

2000 Millbrook Drive, Lincolnshire, IL 60069

2

© Copyright 2012 LG Electronics U.S.A., Inc.

206-4122

Image 2
Contents 206-4122 Rev B For Customer Support/Service, please call­1-888-865-3026 Important safeguards for you and your new product Safety Check Table of Contents Channel Assignments Setup InformationHCS6300 TranscodersFeatures HCS6300 Product DescriptionIntegrated elements of the Transcoder System Transcoder Product DescriptionTypical HD Transcoder System Overview Card Description HCS6300HCS6300 Functional Blocks MUXInstalling a CodePlus Feature Card Slot Satellite STB & HCS6300 Initialization & Setup Connections HD STBSystem Setup Typical HCS6300 System Installation6300 Typical Setup Flow Chart for HCS6300Hdtv Service Feed Combiner Distribution SystemNetwork and Communication Setup Controller Menu Commands Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Access the Controller MenuView HCS6300 System Information Card Card 11 HCS7700 Card 12 HCS7700 Channel MapAvailable cards Card View MUX or Raw Bitrate Data Slot #5 Bitrate Mbit/sMbit/s Mux #1 Output Bitrate 31.746 Mbit/s Mux #2 Output Bitrate 34.051 Mbit/s Slot #8 BitrateSet the HCS6300 IP Address Change the Reload ProIdiom Key Password Reset the Controller card to activate new IP settingsPassword changed Perform an External Card Reset Success. Reset command sent to cardUpdate HCS6300 and/or Transcoder Firmware via Tftp Card Card HWID# is Transcoder Menu CommandsAccess the Transcoder Menu View Hardware Information for a Selected TranscoderView MUX Bitrate Data for a Selected Transcoder Card PI key checksum isView Software Information for a Selected Transcoder View the ProIdiom Key ChecksumCard 1 Channel changed to Satellite STB Menu CommandsCard Reloading the key Successfully reloaded PI key Card 1 Current STB Channel is Card 1 Satellite signal strength is 52%Read the Satellite Signal Strength Read the Current STB ChannelCard 1 STB Powered On Card 1 Satellite signal is lockedCard 1 Access card serial number is Card 1 STB Powered OffSet the Satellite OSD On or Off Card 1 The STB is resettingReset the Satellite STB Read the STB Activation StatusMain Command Configuration Options via Command LineAccess the HCS6300 Main Menu Print the RF Channel Map View HCS6300 System InformationSet HCS6300 RF Channels Perform an External Card Reset Display a List of Transcoder Cards Installed in the ChassisAccess Individual Transcoder Menus Resetting cardInstall a ProIdiom Key on All Transcoders Set the HCS6300 IP AddressTftp Transfer At the Use Tftp to download key y/n? prompt, eitherXmodem File Transfer Reload PI complete OK Update HCS6300 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders At the Use Tftp to transfer files y/n? prompt, eitherView MUX or Raw Bitrate Data Configure Card Number/Channel Assignments Reset Password for Reload PI Key GUI Option Set Cross point switch... OKCaset View Hardware Information for the Selected Transcoder Install a ProIdiom Key on the Selected TranscoderEncoder version Ethernet version Application version View Software Information for the Selected TranscoderReload the ProIdiom Key on the Selected Transcoder View the ProIdiom Key Checksum for the Selected TranscoderReturn to the HCS6300 Main Menu Update Firmware on the Selected TranscoderReset the Selected Transcoder Card Satellite Receiver Menu Commands Access the Satellite Receiver MenuRead the Satellite STB Access Card Number Read the Satellite STB Activation StatusRead the Satellite STB Serial Number At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Set Satellite OSD On or OffAt the Change auto tune settings y/n? prompt, either Return to the Transcoder MenuAudio/Video Freeze or Blank Screen TroubleshootingEquipment Setup Review Status LED Behavior Operating StatusEnvironmental Storage Conditions SpecificationsDimensions Operating ConditionsDate Description Document Revision History / NotesDocument Revision History Open Source Software Notice LG HCS6300 MUX/MOD Feature Card Warranty