LG Electronics HCS6300 setup guide Reload the ProIdiom Key on the Selected Transcoder

Page 42

Configuration Options via Command Line (Cont.)

(Continued from previous page)

Note: The process of updating the encryption key will synchronize the decryption key in any receiver tuned to the cards’ output. If the target receiver is turned off or viewing content from a different card, the synchronization will not occur, and the output will be scrambled. Ensure that all encrypters and decrypters in a system are synchronized to the same key.

1.Confirm the directory location of the Pro:Idiom key (.hex) file. Note: For a TFTP file transfer, the key file must be available on the same machine as the TFTP server.

2.At the [Card (#)] Command > prompt, type pi and press Enter.

3. At the Use TFTP to transfer files (y/n)? prompt, either:

Type y and press Enter to use TFTP for the firmware update.

Type n and press Enter if you will not use TFTP for the firmware update. At the next system prompt: Use XMODEM to transfer files (y/n)?, type y and press Enter.

4.Complete the update using the selected transfer mode (Xmodem or TFTP). Refer to “Install a Pro:Idiom Key on All Transcoders” on page 34 for further information.

The system will display progress messages as well as the result of the installation process. Note that the new key will be stored in non-volatile storage regardless of process results.

Reload the Pro:Idiom Key on the Selected Transcoder

This command reloads the Pro:Idiom encryption key on the selected transcoder card. To reload the Pro:Idiom key on all the transcoders, see “Reload the Pro:Idiom Key on All Transcoders” on page 36.

1.At the [Card (#)] Command > prompt, type pr and press Enter.

2.At the Reload PI key. Continue (y/n)? prompt, type y and press Enter to continue.

When the reload is complete, the system will display confirmation:

Reload PI complete OK

View the Pro:Idiom Key Checksum for the Selected Transcoder

At the [Card (#)] Command > prompt, type cksum and press Enter to display the Pro:Idiom key checksum for the selected transcoder, for example:

PI key checksum is xxxxxxxxxx

where xxxxxxxxxx is a 10-digit number that identifies the Pro:Idiom key file installed on the transcoder.

Note: All transcoder cards in the card frame must have the same Pro:Idiom key file installed.

42

206-4122

Image 42
Contents 206-4122 Rev B For Customer Support/Service, please call­1-888-865-3026 Important safeguards for you and your new product Safety Check Table of Contents Channel Assignments Setup InformationHCS6300 TranscodersFeatures HCS6300 Product DescriptionTranscoder Product Description Typical HD Transcoder System OverviewIntegrated elements of the Transcoder System Card Description HCS6300HCS6300 Functional Blocks MUXInstalling a CodePlus Feature Card Slot Satellite STB & HCS6300 Initialization & Setup Connections HD STBSystem Setup Typical HCS6300 System Installation6300 Typical Setup Flow Chart for HCS6300Hdtv Service Feed Combiner Distribution SystemNetwork and Communication Setup Controller Menu Commands Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Access the Controller MenuView HCS6300 System Information Channel Map Available cards CardCard Card 11 HCS7700 Card 12 HCS7700 View MUX or Raw Bitrate Data Slot #5 Bitrate Mbit/sMbit/s Mux #1 Output Bitrate 31.746 Mbit/s Mux #2 Output Bitrate 34.051 Mbit/s Slot #8 BitrateSet the HCS6300 IP Address Reset the Controller card to activate new IP settings Password changedChange the Reload ProIdiom Key Password Success. Reset command sent to card Update HCS6300 and/or Transcoder Firmware via TftpPerform an External Card Reset Card Card HWID# is Transcoder Menu CommandsAccess the Transcoder Menu View Hardware Information for a Selected TranscoderView MUX Bitrate Data for a Selected Transcoder Card PI key checksum isView Software Information for a Selected Transcoder View the ProIdiom Key ChecksumSatellite STB Menu Commands Card Reloading the key Successfully reloaded PI keyCard 1 Channel changed to Card 1 Current STB Channel is Card 1 Satellite signal strength is 52%Read the Satellite Signal Strength Read the Current STB ChannelCard 1 STB Powered On Card 1 Satellite signal is lockedCard 1 Access card serial number is Card 1 STB Powered OffSet the Satellite OSD On or Off Card 1 The STB is resettingReset the Satellite STB Read the STB Activation StatusConfiguration Options via Command Line Access the HCS6300 Main MenuMain Command View HCS6300 System Information Set HCS6300 RF ChannelsPrint the RF Channel Map Perform an External Card Reset Display a List of Transcoder Cards Installed in the ChassisAccess Individual Transcoder Menus Resetting cardInstall a ProIdiom Key on All Transcoders Set the HCS6300 IP AddressAt the Use Tftp to download key y/n? prompt, either Xmodem File TransferTftp Transfer Reload PI complete OK Update HCS6300 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders At the Use Tftp to transfer files y/n? prompt, eitherView MUX or Raw Bitrate Data Configure Card Number/Channel Assignments Reset Password for Reload PI Key GUI Option Set Cross point switch... OKCaset View Hardware Information for the Selected Transcoder Install a ProIdiom Key on the Selected TranscoderEncoder version Ethernet version Application version View Software Information for the Selected TranscoderReload the ProIdiom Key on the Selected Transcoder View the ProIdiom Key Checksum for the Selected TranscoderUpdate Firmware on the Selected Transcoder Reset the Selected Transcoder CardReturn to the HCS6300 Main Menu Satellite Receiver Menu Commands Access the Satellite Receiver MenuRead the Satellite STB Access Card Number Read the Satellite STB Activation StatusRead the Satellite STB Serial Number At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Set Satellite OSD On or OffAt the Change auto tune settings y/n? prompt, either Return to the Transcoder MenuAudio/Video Freeze or Blank Screen TroubleshootingEquipment Setup Review Status LED Behavior Operating StatusEnvironmental Storage Conditions SpecificationsDimensions Operating ConditionsDocument Revision History / Notes Document Revision HistoryDate Description Open Source Software Notice LG HCS6300 MUX/MOD Feature Card Warranty