LG Electronics HCS6300 At the Satellite # Command prompt, either, Set Satellite OSD On or Off

Page 46

Configuration Options via Command Line (Cont.)

Read the Satellite STB Serial Number

At the [Satellite (#)] Command > prompt, type bnum and press Enter to display the satellite STB serial number, for example:

Card 1: STB serial number is 029265702091

Set Satellite OSD On or Off

At the [Satellite (#)] Command > prompt, either:

•Type osdon and press Enter to enable on-screen display for the video signal at the HDMI output.

•Type osdoff and press Enter to disable on-screen display for the video signal at the HDMI output. Note that the Ethernet video stream does not contain on-screen display.

Power the Satellite STB On or Off

“Turn STB On” and “Turn STB Off” options in the Satellite Receiver Menu enable you to power ON a satellite STB from standby mode or power OFF a satellite STB to standby mode.

At the [Satellite (#)] Command > prompt, either:

•Type on and press Enter to power ON the satellite STB.

•Type off and press Enter to switch the satellite STB to standby mode. HDMI output is disabled, but the Ethernet port continues to stream audio and video.

Reset the Satellite STB

At the [Satellite (#)] Command > prompt, type stbrst and press Enter to reset the satellite STB. After reset, the satellite STB resumes normal operation.

Auto Tune Parameters

The Auto Tune feature, enabled by default to run every day at 3 AM (for approximately 20 seconds), allows the COM 23 satellite STB to re-synchronize its audio and video buffers. The default primary and secondary channels specified for auto tuning purposes are 202 (CNN) and 206 (ESPN), respectively.

You can view the current status of auto tuning, and/or you can modify or disable the auto tune settings, if required.

Read Auto Tune Parameters

At the [Satellite (#)] Command > prompt, type atune and press Enter to view auto tune parameters, for example:

Auto tune is Enabled

Auto tune time (0-23): 3

Primary tune to channel: 202

Secondary tune to channel: 206

46

206-4122

Image 46

Contents 206-4122 Rev B For Customer Support/Service, please call1-888-865-3026 Important safeguards for you and your new product Safety Check Table of Contents Channel Assignments Setup InformationHCS6300 TranscodersFeatures HCS6300 Product DescriptionTypical HD Transcoder System Overview Transcoder Product DescriptionIntegrated elements of the Transcoder System Card Description HCS6300HCS6300 Functional Blocks MUXInstalling a CodePlus Feature Card Slot Satellite STB & HCS6300 Initialization & Setup Connections HD STBSystem Setup Typical HCS6300 System Installation6300 Typical Setup Flow Chart for HCS6300Hdtv Service Feed Combiner Distribution SystemNetwork and Communication Setup Controller Menu Commands Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Access the Controller MenuView HCS6300 System Information Available cards Card Channel MapCard Card 11 HCS7700 Card 12 HCS7700 View MUX or Raw Bitrate Data Slot #5 Bitrate Mbit/sMbit/s Mux #1 Output Bitrate 31.746 Mbit/s Mux #2 Output Bitrate 34.051 Mbit/s Slot #8 BitrateSet the HCS6300 IP Address Password changed Reset the Controller card to activate new IP settingsChange the Reload ProIdiom Key Password Update HCS6300 and/or Transcoder Firmware via Tftp Success. Reset command sent to cardPerform an External Card Reset Card Card HWID# is Transcoder Menu CommandsAccess the Transcoder Menu View Hardware Information for a Selected TranscoderView MUX Bitrate Data for a Selected Transcoder Card PI key checksum isView Software Information for a Selected Transcoder View the ProIdiom Key ChecksumCard Reloading the key Successfully reloaded PI key Satellite STB Menu CommandsCard 1 Channel changed to Card 1 Current STB Channel is Card 1 Satellite signal strength is 52%Read the Satellite Signal Strength Read the Current STB ChannelCard 1 STB Powered On Card 1 Satellite signal is lockedCard 1 Access card serial number is Card 1 STB Powered OffSet the Satellite OSD On or Off Card 1 The STB is resettingReset the Satellite STB Read the STB Activation StatusAccess the HCS6300 Main Menu Configuration Options via Command LineMain Command Set HCS6300 RF Channels View HCS6300 System InformationPrint the RF Channel Map Perform an External Card Reset Display a List of Transcoder Cards Installed in the ChassisAccess Individual Transcoder Menus Resetting cardInstall a ProIdiom Key on All Transcoders Set the HCS6300 IP AddressXmodem File Transfer At the Use Tftp to download key y/n? prompt, eitherTftp Transfer Reload PI complete OK Update HCS6300 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders At the Use Tftp to transfer files y/n? prompt, eitherView MUX or Raw Bitrate Data Configure Card Number/Channel Assignments Reset Password for Reload PI Key GUI Option Set Cross point switch... OKCaset View Hardware Information for the Selected Transcoder Install a ProIdiom Key on the Selected TranscoderEncoder version Ethernet version Application version View Software Information for the Selected TranscoderReload the ProIdiom Key on the Selected Transcoder View the ProIdiom Key Checksum for the Selected TranscoderReset the Selected Transcoder Card Update Firmware on the Selected TranscoderReturn to the HCS6300 Main Menu Satellite Receiver Menu Commands Access the Satellite Receiver MenuRead the Satellite STB Access Card Number Read the Satellite STB Activation StatusRead the Satellite STB Serial Number At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Set Satellite OSD On or OffAt the Change auto tune settings y/n? prompt, either Return to the Transcoder MenuAudio/Video Freeze or Blank Screen TroubleshootingEquipment Setup Review Status LED Behavior Operating StatusEnvironmental Storage Conditions SpecificationsDimensions Operating ConditionsDocument Revision History Document Revision History / NotesDate Description Open Source Software Notice LG HCS6300 MUX/MOD Feature Card Warranty