LG Electronics HCS6300 setup guide Important safeguards for you and your new product

Page 3

IMPORTANT SAFETY INSTRUCTIONS

Important safeguards for you and your new product

THIS PRODUCT HAS BEEN MANUFACTURED AND TESTED WITH SAFETY IN MIND. IMPROPER USE, HOWEVER, CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. TO AVOID DEFEATING THE SAFEGUARDS THAT HAVE BEEN BUILT INTO THIS PRODUCT, PLEASE READ AND OBSERVE THE FOLLOWING SAFETY POINTS WHEN INSTALLING AND USING THIS PRODUCT.

1.Read these instructions.

Read all the safety and operating instructions before operating the product.

2.Keep these instructions.

Retain the safety and operating instructions for future reference.

3.Heed all warnings.

Adhere to all warnings on the product and in the operating instructions.

4.Follow all instructions.

Follow all operating and use instructions.

5.Do not use this apparatus near water.

Do not use this product near water or moisture or in an area, such as a basement, that might become flooded.

6.Clean only with dry cloth.

Unplug this product before cleaning. Do not use liquid cleaners or aerosol cleaners.

7.Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, liquid has been spilled or objects have fallen into the appara- tus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

8.Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

9. Outdoor Use

Warning: To prevent fire or shock hazards, do not expose this product to rain or moisture.

10.Wet Location

The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

11.Test Equipment

In some cases, LG has supplied or recom- mended the use of test equipment and devices for the setup and testing of the equipment. The operation and maintenance of test equipment is described in their associated instruction manuals. Please refer to these manuals for explicit instructions regarding the safe use and handling of the equipment.

12. Damage Requiring Service

Unplug this product from the wall power outlet and refer servicing to qualified service personnel under the following conditions:

a. If liquid has been spilled, or objects have fallen into the product.

b. If the product has been exposed to rain or water.

c. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation.

(Continued on next page)

206-4122

3

Image 3
Contents 206-4122 Rev B For Customer Support/Service, please call­1-888-865-3026 Important safeguards for you and your new product Safety Check Table of Contents Transcoders Setup InformationHCS6300 Channel AssignmentsHCS6300 Product Description FeaturesTranscoder Product Description Typical HD Transcoder System OverviewIntegrated elements of the Transcoder System HCS6300 Card DescriptionMUX HCS6300 Functional BlocksInstalling a CodePlus Feature Card Slot HD STB Satellite STB & HCS6300 Initialization & Setup ConnectionsTypical HCS6300 System Installation System SetupCombiner Distribution System Typical Setup Flow Chart for HCS6300Hdtv Service Feed 6300Network and Communication Setup Access the Controller Menu Configuration Options via GUIAccess the CodePlus Transcoder Series Web GUI Controller Menu CommandsView HCS6300 System Information Channel Map Available cards CardCard Card 11 HCS7700 Card 12 HCS7700 View MUX or Raw Bitrate Data Mux #2 Output Bitrate 34.051 Mbit/s Slot #8 Bitrate Mbit/sMbit/s Mux #1 Output Bitrate 31.746 Mbit/s Slot #5 BitrateSet the HCS6300 IP Address Reset the Controller card to activate new IP settings Password changedChange the Reload ProIdiom Key Password Success. Reset command sent to card Update HCS6300 and/or Transcoder Firmware via TftpPerform an External Card Reset View Hardware Information for a Selected Transcoder Transcoder Menu CommandsAccess the Transcoder Menu Card Card HWID# isView the ProIdiom Key Checksum Card PI key checksum isView Software Information for a Selected Transcoder View MUX Bitrate Data for a Selected TranscoderSatellite STB Menu Commands Card Reloading the key Successfully reloaded PI keyCard 1 Channel changed to Read the Current STB Channel Card 1 Satellite signal strength is 52%Read the Satellite Signal Strength Card 1 Current STB Channel isCard 1 STB Powered Off Card 1 Satellite signal is lockedCard 1 Access card serial number is Card 1 STB Powered OnRead the STB Activation Status Card 1 The STB is resettingReset the Satellite STB Set the Satellite OSD On or OffConfiguration Options via Command Line Access the HCS6300 Main MenuMain Command View HCS6300 System Information Set HCS6300 RF ChannelsPrint the RF Channel Map Resetting card Display a List of Transcoder Cards Installed in the ChassisAccess Individual Transcoder Menus Perform an External Card ResetSet the HCS6300 IP Address Install a ProIdiom Key on All TranscodersAt the Use Tftp to download key y/n? prompt, either Xmodem File TransferTftp Transfer At the Use Tftp to transfer files y/n? prompt, either Update HCS6300 and/or Transcoder FirmwareReload the ProIdiom Key on All Transcoders Reload PI complete OKView MUX or Raw Bitrate Data Configure Card Number/Channel Assignments Set Cross point switch... OK Reset Password for Reload PI Key GUI OptionCaset View Software Information for the Selected Transcoder Install a ProIdiom Key on the Selected TranscoderEncoder version Ethernet version Application version View Hardware Information for the Selected TranscoderView the ProIdiom Key Checksum for the Selected Transcoder Reload the ProIdiom Key on the Selected TranscoderUpdate Firmware on the Selected Transcoder Reset the Selected Transcoder CardReturn to the HCS6300 Main Menu Access the Satellite Receiver Menu Satellite Receiver Menu CommandsRead the Satellite STB Activation Status Read the Satellite STB Access Card NumberSet Satellite OSD On or Off At the Satellite # Command prompt, eitherPower the Satellite STB On or Off Read the Satellite STB Serial NumberReturn to the Transcoder Menu At the Change auto tune settings y/n? prompt, eitherStatus LED Behavior Operating Status TroubleshootingEquipment Setup Review Audio/Video Freeze or Blank ScreenOperating Conditions SpecificationsDimensions Environmental Storage ConditionsDocument Revision History / Notes Document Revision HistoryDate Description Open Source Software Notice LG HCS6300 MUX/MOD Feature Card Warranty