Runco PL-50DHD Using This Manual, Certain features, Degrade performance or cause a malfunction

Page 12

Introduction

Graphic Conventions: These symbols appear in numerous places throughout the manual, to emphasize points that you must keep in mind to avoid problems with your equipment or injury:

Tip

TIPS highlight time-saving short cuts and helpful guidelines for using

certain features.

Note

NOTES emphasize text with unusual importance or special

significance. They also provide supplemental information.

Caution

CAUTIONS alert users that a given action or omitted action can

degrade performance or cause a malfunction.

 

WARNING

WARNINGS appear when a given action or omitted action can result

in damage to the equipment, or possible non-fatal injury to the user.

DANGER!

DANGER appears when a given action can cause severe injury or

death.

 

1.2

Using This Manual

Use the following table to locate the specific information you need in this manual.

If you need...

... Turn to page:

 

 

Information about obtaining service

iv

 

 

General information about the PlasmaWall

3

Flat-Panel Plasma Display Monitor and DHD Con-

 

troller

 

 

 

Installation instructions

15

 

 

First-time configuration instructions

29

 

 

Advanced configuration instructions

41

 

 

Troubleshooting tips

47

 

 

Specifications for the PlasmaWall Flat-Panel

55

Plasma Display Monitor and DHD Controller

 

 

 

2 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Image 12
Contents PL-43DHD PL-50DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsAppendix A. PlasmaWall Service Remote Control OperationList of Figures Page Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Indicators Controls and FunctionsPlasmaWall at a Glance PlasmaWall Connectors Main Power Switch External Speaker Output RightCombination IN/OUT Digital RGB Input 2 DVI-DPower Button DHD Controller Front PanelRunco Icon IR SensorUP Button Left ButtonEnter Button Down ButtonHD1 / HD2 Analog BNC connectors Component Video RCA connectorsDHD Controller Rear Panel DVI OUTComposite Video Input RS-232 Control PortMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlIR Output Indicator EnterLight MenuCinema SVCISF DAY CustInstallation Remote ControlOther surfaces Quick Setup Installation specialistStep Procedure For Details, refer to Installation ConsiderationsHigh-Altitude Operation Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Connecting Source Components to the DHDDVI Connections See Figure DTV or Progressive Component YPbPr Source Refer to Computer/Video Signal Compatibility on page 58 for Analog Computer RGB Connections See FigureTo work Some Macintosh computers may require a Macintosh videoComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection11. Installing the Cable Ties Turning on the Power OperationSelecting the Input Source Setting the PC Display Properties You must enter a passcode to access the Service menuOperation Using the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Resolution Input PositionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.001B Date Mar 24You must enter a passcode to access the Calibration menu Gain/Offset Refer to ISF Night Display Color, aboveCalibration Service Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Maintenance and Troubleshooting Troubleshooting TipsSymptom Possible Causes Solution Computer/Video Signal Command Value Description Min/max Stored? Power On/Off CommandsSerial Communications Aspect Ratio Commands Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Page Specifications PlasmaWall SpecificationsSpecifications are subject to change without notice PL-43DHD 380 W PL-50DHD 480 WDHD Controller Specifications PlasmaWall Dimensions PlasmaWall Model PL-43DHD DimensionsPlasmaWall Model PL-50DHD Dimensions Computer/Video Signal Compatibility Resolution Remarks SupportInput Refresh Rate Display Quality Refer to Notes Vert Horiz75.1 68.5 Figure A-1. PlasmaWall Service Remote Control OverviewPower Aspect RatioInfo SET ButtonVideo NR Noise Reduction Mpeg FilterPage Page Runco CL-810 Owner’s Operating Manual