Runco PL-43DHD, PL-50DHD manual Serial Communications, Command

Page 59

6. Serial Communications

To interface the PlasmaWall with a home theater automation/control system or a PC running terminal emulation software, connect it to the RS-232 output of the DHD Controller as shown in Figure 3-3.Connect your control system or PC to the RS-232 input of the DHD Controller as shown in Figure 3-9.

Configure the RS-232 controller or PC serial port as follows: no parity, eight (8) data bits, one (1) stop bit and no flow control. Set the baud rate to 19200, to match that of the DHD Controller RS-232 port.

Serial commands to the DHD Controller take the following form:

Commands are not case-sensitive.

For a single command that takes no parameters, type the command followed by a carriage return; for example, to set the aspect ratio to Letterbox, type

LETTERBOX <Enter>.

For a single command that takes a parameter, type the command, a space or a comma and the desired value followed by a carriage return; for example, to set the brightness to -10, type BRIGHTNESS -10<Enter> or

BRIGHTNESS,-10 <Enter>.

You can also send a string of multiple commands on a single line, separated by commas. For example, COMPOSITE,BRIGHTNESS 100,ANAMORPHIC <Enter> switches to the Composite video input, sets the brightness to 100 and sets the aspect ratio to Anamorphic. Command strings can be up to 255 characters long.

Avoid combining the ON or POWER 1 commands with other commands Note on a single line. After sending ON or POWER 1, allow at least 15

seconds for the DHD Controller to power up. Once it does, it will accept and properly execute multiple serial commands.

Table 6-1lists the RS-232 command set. The “Parameter (min/max)” column shows the valid parameter ranges, or “NA” for commands that take no parameters.

When you enter a valid command, the DHD Controller executes it and acknowledges it with a plus sign on the command line (+ >). When you enter an invalid command – one that is misspelled or followed by values outside the valid range for that command – the DHD Controller ignores it and returns a minus sign (- >).

Table 6-1. Serial Commands

Command

Parameter

 

Value

Description

(min/max)

 

Stored?

 

 

 

 

 

 

 

 

 

 

Power On/Off Commands

 

 

 

 

 

OFF

NA

 

NA

Turns system off

 

 

 

 

 

ON

NA

 

NA

Turns system on

 

 

 

 

 

POWER

0/1

 

NA

Turns system on or off (toggles on/off state)

 

 

 

 

 

POWER?

NA

 

NA

Returns power status

 

 

 

 

 

6.1

RS-232 Connection and Port Configuration

6.2

Serial Command Syntax

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

49

Image 59
Contents PL-43DHD PL-50DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC DOC Compliance Notice Safety PrecautionsTable of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. PlasmaWall Service Remote ControlList of Figures Page About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions PlasmaWall Connectors Digital RGB Input 2 DVI-D Main Power SwitchExternal Speaker Output Right Combination IN/OUTIR Sensor Power ButtonDHD Controller Front Panel Runco IconDown Button UP ButtonLeft Button Enter ButtonDVI OUT HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors DHD Controller Rear PanelMain AC Fuse Composite Video InputRS-232 Control Port DHD Controller Remote Control DHD Controller Remote ControlMenu IR Output IndicatorEnter LightCust CinemaSVC ISF DAYRemote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupInstallation specialist Mounting the PlasmaWall InstallationConsiderations High-Altitude OperationVentilation Ambient LightInstallation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Connections See Figure Connecting SourceComponents to the DHD DTV or Progressive Component YPbPr Source Some Macintosh computers may require a Macintosh video Refer to Computer/Video Signal Compatibility on page 58 forAnalog Computer RGB Connections See Figure To workComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 Controller11. Installing the Cable Ties Operation Turning on the PowerYou must enter a passcode to access the Service menu Selecting the Input Source Setting the PC Display PropertiesOperation Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position Serial Number Hardware Firmware 0002.001B Date Mar 24 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationCalibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Should be used by ISF-certified technicians only ServiceButton takes you from top to bottom in the left column, then Input Names Restore Composite Video Component SDMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Computer/Video Signal Serial Communications CommandValue Description Min/max Stored? Power On/Off Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Page PL-43DHD 380 W PL-50DHD 480 W SpecificationsPlasmaWall Specifications Specifications are subject to change without noticeDHD Controller Specifications PlasmaWall Model PL-43DHD Dimensions PlasmaWall DimensionsPlasmaWall Model PL-50DHD Dimensions Vert Horiz Computer/Video Signal CompatibilityResolution Remarks Support Input Refresh Rate Display Quality Refer to Notes75.1 68.5 Overview Figure A-1. PlasmaWall Service Remote ControlSET Button PowerAspect Ratio InfoMpeg Filter Video NR Noise ReductionPage Page Runco CL-810 Owner’s Operating Manual