Runco PL-50DHD, PL-43DHD manual Selecting the Input Source Setting the PC Display Properties

Page 40

Operation

4.2

Selecting the Input Source

4.3

Setting the PC Display Properties

By default, the PlasmaWall is configured to display the signal received on its RGBHV (ANALOG RGB IN) input. To use the DVI-D (DIGITAL RGB) input instead:

1. Press MENU and enter the Service Menu passcode.

You must enter a passcode to access the Service menu.

Note

2.Select Service from the Main Menu.

3.Select Display Device from the Service Menu.

4.Press to select DVI/HDMI, then press ENTER.

To maximize image quality when using the PlasmaWall with a personal computer, you may need to adjust the display properties of your PC video card. To do this:

1.Choose Settings from the Windows Start menu and click on “Control Panel.”

2.Double click on the Display icon.

3.Click the Settings tab on the display dialog box.

4.Adjust the resolution to 1024x768 or 1280x768 pixels.

30 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Image 40

Contents PL-43DHD PL-50DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsAppendix A. PlasmaWall Service Remote Control OperationList of Figures Page Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance PlasmaWall Connectors Main Power Switch External Speaker Output RightCombination IN/OUT Digital RGB Input 2 DVI-DPower Button DHD Controller Front PanelRunco Icon IR SensorUP Button Left ButtonEnter Button Down ButtonHD1 / HD2 Analog BNC connectors Component Video RCA connectorsDHD Controller Rear Panel DVI OUTRS-232 Control Port Composite Video InputMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlIR Output Indicator EnterLight MenuCinema SVCISF DAY CustInstallation Remote ControlOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Installation ConsiderationsHigh-Altitude Operation Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceDVI Connections See Figure DTV or Progressive Component YPbPr Source Refer to Computer/Video Signal Compatibility on page 58 for Analog Computer RGB Connections See FigureTo work Some Macintosh computers may require a Macintosh videoComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection11. Installing the Cable Ties Turning on the Power OperationSelecting the Input Source Setting the PC Display Properties You must enter a passcode to access the Service menuOperation Using the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.001B Date Mar 24Gain/Offset Refer to ISF Night Display Color, above You must enter a passcode to access the Calibration menuCalibration Service Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Troubleshooting Tips Maintenance and TroubleshootingSymptom Possible Causes Solution Computer/Video Signal Value Description Min/max Stored? Power On/Off Commands CommandSerial Communications Aspect Ratio Commands Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Page Specifications PlasmaWall SpecificationsSpecifications are subject to change without notice PL-43DHD 380 W PL-50DHD 480 WDHD Controller Specifications PlasmaWall Dimensions PlasmaWall Model PL-43DHD DimensionsPlasmaWall Model PL-50DHD Dimensions Computer/Video Signal Compatibility Resolution Remarks SupportInput Refresh Rate Display Quality Refer to Notes Vert Horiz75.1 68.5 Figure A-1. PlasmaWall Service Remote Control OverviewPower Aspect RatioInfo SET ButtonVideo NR Noise Reduction Mpeg FilterPage Page Runco CL-810 Owner’s Operating Manual