Runco PL-43DHD, PL-50DHD manual HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV

Page 55

Operation

HD Format: If the characteristics of the incoming signal on the HD1 or HD2 inputs are known, select HD Format from the Service menu and set them as described below. Doing so can reduce the time it takes the DHD Controller to switch from HD to 480i signals or vice versa.

This is generally not necessary unless the DHD Controller – for whatever reason – has difficulty determining the color space (RGB or YUV), bandwidth or resolution of the incoming HD signal. In most situations, the Auto settings work well.

•HD/RGB 1 and HD/RGB 2 (Color Space): Select Auto, RGB or YUV.

•ADC Bandwidth: Select Auto, 75 MHz, 150 MHz or 300 MHz.

•YPbPr Input Resolution: Select Auto or specify the input resolution, if known: 480i, 480p, 576i, 576p, 720p or 1080i.

Triggers: Select Triggers from the Service menu to configure the 12-volt trigger outputs. You can assign one or more trigger outputs to each aspect ratio. Those triggers are then activated by selecting that aspect ratio.

To save the trigger settings so that they can be restored after a System Reset (described below), press repeatedly to highlight “Save.” Then, press ENTER.

Miscellaneous: Select Miscellaneous from the Service menu to set the following options:

•Language: Select Language from the Miscellaneous menu and press the up- or down-arrows to select the OSD language. (Currently, only English is supported.)

•Menu Mode: This is the manner in which the OSD menus appear and disappear when you press MENU. Choose one of the following:

0 = No transition; menus abruptly appear and disappear.

1 = Menus fade in and out.

2 = “Checkerboard” dissolve; menus appear and disappear in sections.

3 = “Window shade” effect; menus are drawn on a diagonal from top left to bottom right, and retract in the opposite direction.

•Timeout - Short/Long: These settings control how long the OSD menus stay on screen. Select a time-out period of from 2 to 60 seconds.

•Side Bar Color: This controls the color of the inactive image area. The range is from -100 (black) to 100 (white).

The inactive image area is on either side of the active image area when using the Standard 4:3 aspect ratio (or the entire screen when no incoming video signal is present).

•Film Mode: Enable Film Mode to smooth out moving images from interlaced, standard-definition (SD) sources. In most cases, the PlasmaWall detects the proper “pull-down” rate and vertical frequency. However, if your source is jittery and/or tearing you may wish to enable Film Mode to ensure stable processing for that source.

Resolution: The DHD Controller defaults to an output resolution of 720p. When using the PlasmaWall with a computer or certain HD sources, you may want to force the DHD Controller to use a different output resolution. If so, select Resolution from the Service menu and choose one. Then, press ENTER to confirm.

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

45

Page 54 Page 56
Image 55
Page 54 Page 56
Contents PL-43DHD PL-50DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC DOC Compliance Notice Safety PrecautionsTable of Contents Operation Maintenance and TroubleshootingSpecifications Appendix A. PlasmaWall Service Remote ControlList of Figures Page About This Manual IntroductionDegrade performance or cause a malfunction Using This ManualCertain features Significance. They also provide supplemental informationKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance PlasmaWall Connectors Digital RGB Input 2 DVI-D Main Power SwitchExternal Speaker Output Right Combination IN/OUTIR Sensor Power ButtonDHD Controller Front Panel Runco IconDown Button UP ButtonLeft Button Enter ButtonDVI OUT HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors DHD Controller Rear PanelRS-232 Control Port Composite Video InputMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlMenu IR Output IndicatorEnter LightCust CinemaSVC ISF DAYRemote Control InstallationOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Mounting the PlasmaWall InstallationConsiderations High-Altitude OperationVentilation Ambient LightInstallation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceDVI Connections See Figure DTV or Progressive Component YPbPr Source Some Macintosh computers may require a Macintosh video Refer to Computer/Video Signal Compatibility on page 58 forAnalog Computer RGB Connections See Figure To workComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 Controller11. Installing the Cable Ties Operation Turning on the PowerYou must enter a passcode to access the Service menu Selecting the Input Source Setting the PC Display PropertiesOperation Using the On-Screen Menus Aspect Ratio ISF PresetsService Input SourceHD Pass Thru 1 HD Pass Thru Main MenuInput Source Aspect RatioRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan Serial Number Hardware Firmware 0002.001B Date Mar 24 ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default InformationGain/Offset Refer to ISF Night Display Color, above You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians only ServiceButton takes you from top to bottom in the left column, then Input Names Restore Composite Video Component SDMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Troubleshooting Tips Maintenance and TroubleshootingSymptom Possible Causes Solution Computer/Video Signal Value Description Min/max Stored? Power On/Off Commands CommandSerial Communications Aspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Page PL-43DHD 380 W PL-50DHD 480 W SpecificationsPlasmaWall Specifications Specifications are subject to change without noticeDHD Controller Specifications PlasmaWall Model PL-43DHD Dimensions PlasmaWall DimensionsPlasmaWall Model PL-50DHD Dimensions Vert Horiz Computer/Video Signal CompatibilityResolution Remarks Support Input Refresh Rate Display Quality Refer to Notes75.1 68.5 Overview Figure A-1. PlasmaWall Service Remote ControlSET Button PowerAspect Ratio InfoMpeg Filter Video NR Noise ReductionPage Page Runco CL-810 Owner’s Operating Manual
Top Page Image Contents