Runco PL-43DHD, PL-50DHD manual Button takes you from top to bottom in the left column, then

Page 53

Input Names: You can give each DHD Controller input a descriptive name. For example, you may want to change the default input name to the type of source component connected to it: “VCR,” “DVD,” “Laptop” et cetera. Composite, S-Video and Component SD input names can be up to 12 characters long; the others can be up to eight characters long.

To edit an input name, select Input Names from the Service menu. Press or to select an input and press ENTER. Use the or buttons to change a character; press or to select a character to change. When you have finished editing the input name, press MENU.

To restore the default input name, press repeatedly to highlight that input name in the “Restore” column. Then, press ENTER.

To save input names so that they can be restored after a System Reset (described on page 46), press repeatedly to highlight “Save.” Then, press ENTER.

The button takes you from top to bottom in the left column, then

Note from top to bottom in the right column. To highlight “Save,” scroll through both columns.

Remote Control: The Remote Control menu shows you the primary and secondary infrared (IR) codes to which the DHD Controller will respond. By default, both are set to

17. You can change these codes if either:

Another device in the theater (a DVD player, for example) is responding to commands from the DHD Controller remote control (Figure 2-5)in ways that are unpredictable or undesirable.

You have multiple DHD Controllers and want to control them independently, as opposed to broadcasting commands from a single remote to all of them. In this scenario, you can use multiple remotes programmed to use different IR codes. Or, you can use a single remote and change the IR code as needed to address a specific device.

Use the DHD Controller front-panel keypad to change its IR code.

Tip Then, change the code sent by the remote to match as described below.

Do not change the “Type” setting in this menu.

Note

When you change a remote code on the DHD Controller, you must re-program your remote control to send that same code. To do this:

1. Using a straightened paper clip or similar object, press and hold the CODE button on the remote control for approximately three seconds, or until the red LED on the remote lights solid red.

2. Enter a new two-digit code between 00 and 31 inclusive. Include a leading zero for single-digit codes; for example, enter 9 as “09.”

3.The LED turns off to confirm the code change. If you enter an invalid code, the LED flashes for three or four seconds. Try again, entering a valid code.

Input Names

 

Restore

Composite

Composite

 

 

S-Video 1

S-Video 1

S-Video 2

S-Video 2

Component SD

Component SD

HD/RGB 1

HD/RGB 1

HD/RGB 2

HD/RGB 2

DVI 1

DVI 1

DVI 2

DVI 2

Save

 

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

43

Image 53
Contents PL-43DHD PL-50DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC DOC Compliance Notice Safety PrecautionsTable of Contents Specifications Maintenance and TroubleshootingAppendix A. PlasmaWall Service Remote Control OperationList of Figures Page About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionKey Features and Benefits Description, Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions PlasmaWall Connectors External Speaker Output Right Main Power SwitchCombination IN/OUT Digital RGB Input 2 DVI-DDHD Controller Front Panel Power ButtonRunco Icon IR SensorLeft Button UP ButtonEnter Button Down ButtonComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsDHD Controller Rear Panel DVI OUTMain AC Fuse Composite Video InputRS-232 Control Port DHD Controller Remote Control DHD Controller Remote ControlEnter IR Output IndicatorLight MenuSVC CinemaISF DAY CustRemote Control InstallationOther surfaces Step Procedure For Details, refer to Quick SetupInstallation specialist Considerations InstallationHigh-Altitude Operation Mounting the PlasmaWallVentilation Ambient LightInstallation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Connections See Figure Connecting SourceComponents to the DHD DTV or Progressive Component YPbPr Source Analog Computer RGB Connections See Figure Refer to Computer/Video Signal Compatibility on page 58 forTo work Some Macintosh computers may require a Macintosh videoComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 Controller11. Installing the Cable Ties Operation Turning on the PowerYou must enter a passcode to access the Service menu Selecting the Input Source Setting the PC Display PropertiesOperation Using the On-Screen Menus Service ISF PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio HD Pass Thru 1 HD Pass ThruRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position ISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Serial Number Hardware Firmware 0002.001B Date Mar 24Calibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Should be used by ISF-certified technicians only ServiceButton takes you from top to bottom in the left column, then Input Names Restore Composite Video Component SDMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Computer/Video Signal Serial Communications CommandValue Description Min/max Stored? Power On/Off Commands Aspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Page PlasmaWall Specifications SpecificationsSpecifications are subject to change without notice PL-43DHD 380 W PL-50DHD 480 WDHD Controller Specifications PlasmaWall Model PL-43DHD Dimensions PlasmaWall DimensionsPlasmaWall Model PL-50DHD Dimensions Resolution Remarks Support Computer/Video Signal CompatibilityInput Refresh Rate Display Quality Refer to Notes Vert Horiz75.1 68.5 Overview Figure A-1. PlasmaWall Service Remote ControlAspect Ratio PowerInfo SET ButtonMpeg Filter Video NR Noise ReductionPage Page Runco CL-810 Owner’s Operating Manual