Runco PL-50DHD Installation, Considerations, High-Altitude Operation, Mounting the PlasmaWall

Page 28

Installation

3.3	Proper installation of your PlasmaWall will ensure the highest possible picture quality.
Installation	Whether you are installing the PlasmaWall temporarily or permanently, you should take the
Considerations	following into account to ensure that it performs optimally.

High-Altitude Operation ➤	Due to the design of all plasma glass panels made by every manufacturer, and the
	interaction between ambient air pressure and the plasma gases contained inside of the
	panel, reliable operation of your plasma display cannot be assured during operation at
	certain high-altitude locations.
	Runco has found this plasma monitor to operate reliablly at altitudes of up to 5000 MSL
	(mean sea level). At elevations higher than this, each panel may react differently,
	depending upon the altitude, air pressure, humidity and other meteorological factors.
	For this reason, Runco International makes no warranties or claims as to the reliable
	operation of the PL-43DHD or PL-50DHD at altitudes greater than 5000 feet above sea
	level. If you are planning to use this product at a location above 5000 feet, please contact
	Runco technical support for further information.
Mounting the PlasmaWall ➤	To install the PlasmaWall, you will need either an optional table stand or wall-mounting kit.
on a Wall or Table Stand	The PlasmaWall cannot be installed on its own.
	If you do decide to wall-mount the PlasmaWall, ensure that the wall-mount bracket is
	installed according to the instructions included with it. The wall must be capable of
	supporting a redundant weight factor three (3) times the weight of the display, or be
	reinforced.
	Runco recommends that this be done by a custom installation specialist.
	Note	Use only a Runco-approved wall-mount kit or table stand that is
		specifically designed for your display.

You can attach your optional mounts or stand to the PlasmaWall in either of two ways:

• While it is upright.

18 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Image 28

Contents PL-43DHD PL-50DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Maintenance and Troubleshooting SpecificationsAppendix A. PlasmaWall Service Remote Control OperationList of Figures Page Introduction About This ManualUsing This Manual Certain featuresSignificance. They also provide supplemental information Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance PlasmaWall Connectors Main Power Switch External Speaker Output RightCombination IN/OUT Digital RGB Input 2 DVI-DPower Button DHD Controller Front PanelRunco Icon IR SensorUP Button Left ButtonEnter Button Down ButtonHD1 / HD2 Analog BNC connectors Component Video RCA connectorsDHD Controller Rear Panel DVI OUTRS-232 Control Port Composite Video InputMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlIR Output Indicator EnterLight MenuCinema SVCISF DAY CustInstallation Remote ControlOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Installation ConsiderationsHigh-Altitude Operation Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceDVI Connections See Figure DTV or Progressive Component YPbPr Source Refer to Computer/Video Signal Compatibility on page 58 for Analog Computer RGB Connections See FigureTo work Some Macintosh computers may require a Macintosh videoComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection11. Installing the Cable Ties Turning on the Power OperationSelecting the Input Source Setting the PC Display Properties You must enter a passcode to access the Service menuOperation Using the On-Screen Menus ISF Presets ServiceInput Source Aspect RatioMain Menu Input SourceAspect Ratio HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Presets ISF Night ISF Day Custom Save Factory DefaultInformation Serial Number Hardware Firmware 0002.001B Date Mar 24Gain/Offset Refer to ISF Night Display Color, above You must enter a passcode to access the Calibration menuCalibration Service Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Troubleshooting Tips Maintenance and TroubleshootingSymptom Possible Causes Solution Computer/Video Signal Value Description Min/max Stored? Power On/Off Commands CommandSerial Communications Aspect Ratio Commands Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Page Specifications PlasmaWall SpecificationsSpecifications are subject to change without notice PL-43DHD 380 W PL-50DHD 480 WDHD Controller Specifications PlasmaWall Dimensions PlasmaWall Model PL-43DHD DimensionsPlasmaWall Model PL-50DHD Dimensions Computer/Video Signal Compatibility Resolution Remarks SupportInput Refresh Rate Display Quality Refer to Notes Vert Horiz75.1 68.5 Figure A-1. PlasmaWall Service Remote Control OverviewPower Aspect RatioInfo SET ButtonVideo NR Noise Reduction Mpeg FilterPage Page Runco CL-810 Owner’s Operating Manual