Runco PL-43DHD, PL-50DHD manual Resolution, Input Position

Page 49

Sharpness: “Sharpness” is the amount of high-frequency detail in the image. To adjust sharpness, select Sharpness from the Picture menu and press ENTER. On your external test pattern source, select a pattern like the one shown in Figure 4-5.Adjust as needed, looking for white edges around the transitions from black to gray and differently-sized lines in the “sweep” patterns at the top and bottom. Lower the sharpness setting to eliminate them.

Figure 4-5. Typical Test Pattern for Adjusting Sharpness

Use the controls in the Input Position Menu to fine-tune the aspect ratio and image position for the current source.

Note

The input position settings are automatically saved for each input

and resolution.

Left/Right: Select Left/Right from the Input Position menu to shift the projected image horizontally. Use the right or up cursor button to shift the image to the right; use the left or down button to shift it to the left.

Up/Down: Select Up/Down from the Input Position menu to shift the projected image vertically. Use the right or up cursor button to shift the image upward; use the left or down button to shift it downward.

Width: Select Width from the Input Position menu to change the projected image width. Use the right or up cursor button to increase the width; use the left or down button to decrease it.

Height: Select Height from the Input Position menu to change the projected image height. Use the right or up cursor button to increase the height; use the left or down button to decrease it.

Input Position

Input Position

Left/Right

Up/Down

Width

Height

Overscan

Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

39

Image 49
Contents PL-43DHD PL-50DHD Page For Plasma Displays Three Year Limited WarrantyRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC DOC Compliance Notice Safety PrecautionsTable of Contents Specifications Maintenance and TroubleshootingAppendix A. PlasmaWall Service Remote Control OperationList of Figures Page About This Manual IntroductionCertain features Using This ManualSignificance. They also provide supplemental information Degrade performance or cause a malfunctionKey Features and Benefits Description, Features and BenefitsOptional Accessories Controls and Functions Controls and IndicatorsPlasmaWall at a Glance PlasmaWall Connectors External Speaker Output Right Main Power SwitchCombination IN/OUT Digital RGB Input 2 DVI-DDHD Controller Front Panel Power ButtonRunco Icon IR SensorLeft Button UP ButtonEnter Button Down ButtonComponent Video RCA connectors HD1 / HD2 Analog BNC connectorsDHD Controller Rear Panel DVI OUTRS-232 Control Port Composite Video InputMain AC Fuse DHD Controller Remote Control DHD Controller Remote ControlEnter IR Output IndicatorLight MenuSVC CinemaISF DAY CustRemote Control InstallationOther surfaces Installation specialist Quick SetupStep Procedure For Details, refer to Considerations InstallationHigh-Altitude Operation Mounting the PlasmaWallVentilation Ambient LightInstallation Connections to the PlasmaWall and DHD Controller Connecting PlasmaWall to the DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall Components to the DHD Connecting SourceDVI Connections See Figure DTV or Progressive Component YPbPr Source Analog Computer RGB Connections See Figure Refer to Computer/Video Signal Compatibility on page 58 forTo work Some Macintosh computers may require a Macintosh videoComposite, S-Video and Component Video Connections Composite/S-Video/Component Video Connections See FigureConnection RS-232 Controller11. Installing the Cable Ties Operation Turning on the PowerYou must enter a passcode to access the Service menu Selecting the Input Source Setting the PC Display PropertiesOperation Using the On-Screen Menus Service ISF PresetsInput Source Aspect RatioInput Source Main MenuAspect Ratio HD Pass Thru 1 HD Pass ThruRemote Aspect Ratio Control Description Key Aspect Ratio SettingsPicture Brightness Contrast Color Tint Sharpness PictureTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position ResolutionInput Position Left/Right Up/Down Width Height Overscan ISF Presets ISF Night ISF Day Custom Save Factory Default ISF PresetsInformation Serial Number Hardware Firmware 0002.001B Date Mar 24Gain/Offset Refer to ISF Night Display Color, above You must enter a passcode to access the Calibration menuCalibration Should be used by ISF-certified technicians only ServiceButton takes you from top to bottom in the left column, then Input Names Restore Composite Video Component SDMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Troubleshooting Tips Maintenance and TroubleshootingSymptom Possible Causes Solution Computer/Video Signal Value Description Min/max Stored? Power On/Off Commands CommandSerial Communications Aspect Ratio Commands Image Preset Commands Output Shift Commands Value Description Min/max Stored? Input Position CommandsBkgnd Page PlasmaWall Specifications SpecificationsSpecifications are subject to change without notice PL-43DHD 380 W PL-50DHD 480 WDHD Controller Specifications PlasmaWall Model PL-43DHD Dimensions PlasmaWall DimensionsPlasmaWall Model PL-50DHD Dimensions Resolution Remarks Support Computer/Video Signal CompatibilityInput Refresh Rate Display Quality Refer to Notes Vert Horiz75.1 68.5 Overview Figure A-1. PlasmaWall Service Remote ControlAspect Ratio PowerInfo SET ButtonMpeg Filter Video NR Noise ReductionPage Page Runco CL-810 Owner’s Operating Manual