Runco PL-50DHD, PL-43DHD manual Other surfaces

Page 26

Installation

•Do not drop the remote control or expose it to moisture or high temperature.

•The remote control may malfunction under a fluorescent lamp. If that occurs, move the plasma display away from the fluorescent lamp.

•Make sure that there is nothing obstructing the infrared beam between the remote control and the IR receiver on the plasma display.

Note	The signal from the remote control can be reflected by walls or
	other surfaces.

•If the effective range of the remote control decreases, or it stops working, replace the batteries with new ones.

•Ambient conditions may possibly impede the operation of the remote control. If this happens, point the remote control at the plasma display and repeat the operation.

16 Runco PL-43DHD and PL-50DHD Owner’s Operating Manual

Image 26

Contents PL-43DHD PL-50DHD Page Three Year Limited Warranty For Plasma DisplaysRIGHTS, Limits and Exclusions Runco INTERNATIONAL, INC Safety Precautions DOC Compliance NoticeTable of Contents Appendix A. PlasmaWall Service Remote Control Maintenance and TroubleshootingSpecifications OperationList of Figures Page Introduction About This ManualSignificance. They also provide supplemental information Using This ManualCertain features Degrade performance or cause a malfunctionDescription, Features and Benefits Key Features and BenefitsOptional Accessories PlasmaWall at a Glance Controls and IndicatorsControls and Functions PlasmaWall Connectors Combination IN/OUT Main Power SwitchExternal Speaker Output Right Digital RGB Input 2 DVI-DRunco Icon Power ButtonDHD Controller Front Panel IR SensorEnter Button UP ButtonLeft Button Down ButtonDHD Controller Rear Panel HD1 / HD2 Analog BNC connectorsComponent Video RCA connectors DVI OUTMain AC Fuse Composite Video InputRS-232 Control Port DHD Controller Remote Control DHD Controller Remote ControlLight IR Output IndicatorEnter MenuISF DAY CinemaSVC CustInstallation Remote ControlOther surfaces Step Procedure For Details, refer to Quick SetupInstallation specialist High-Altitude Operation InstallationConsiderations Mounting the PlasmaWallAmbient Light VentilationInstallation Connecting PlasmaWall to the DHD Controller Connections to the PlasmaWall and DHD ControllerRS-232 Connection from the DHD Controller to the PlasmaWall DVI Connections See Figure Connecting SourceComponents to the DHD DTV or Progressive Component YPbPr Source To work Refer to Computer/Video Signal Compatibility on page 58 forAnalog Computer RGB Connections See Figure Some Macintosh computers may require a Macintosh videoComposite/S-Video/Component Video Connections See Figure Composite, S-Video and Component Video ConnectionsRS-232 Controller Connection11. Installing the Cable Ties Turning on the Power OperationSelecting the Input Source Setting the PC Display Properties You must enter a passcode to access the Service menuOperation Using the On-Screen Menus Input Source ISF PresetsService Aspect RatioAspect Ratio Main MenuInput Source HD Pass Thru 1 HD Pass ThruAspect Ratio Settings Remote Aspect Ratio Control Description KeyPicture Picture Brightness Contrast Color Tint SharpnessTypical Gray Bar Pattern for Adjusting Contrast Gray Yellow Cyan Green Magenta Red Blue Input Position Left/Right Up/Down Width Height Overscan ResolutionInput Position Information ISF PresetsISF Presets ISF Night ISF Day Custom Save Factory Default Serial Number Hardware Firmware 0002.001B Date Mar 24Calibration You must enter a passcode to access the Calibration menuGain/Offset Refer to ISF Night Display Color, above Service Should be used by ISF-certified technicians onlyInput Names Restore Composite Video Component SD Button takes you from top to bottom in the left column, thenMirror Mode HD/RGB 1 and HD/RGB 2 Color Space Select Auto, RGB or YUV Operation Symptom Possible Causes Solution Maintenance and TroubleshootingTroubleshooting Tips Computer/Video Signal Serial Communications CommandValue Description Min/max Stored? Power On/Off Commands Aspect Ratio Commands Image Preset Commands Value Description Min/max Stored? Input Position Commands Output Shift CommandsBkgnd Page Specifications are subject to change without notice SpecificationsPlasmaWall Specifications PL-43DHD 380 W PL-50DHD 480 WDHD Controller Specifications PlasmaWall Dimensions PlasmaWall Model PL-43DHD DimensionsPlasmaWall Model PL-50DHD Dimensions Input Refresh Rate Display Quality Refer to Notes Computer/Video Signal CompatibilityResolution Remarks Support Vert Horiz75.1 68.5 Figure A-1. PlasmaWall Service Remote Control OverviewInfo PowerAspect Ratio SET ButtonVideo NR Noise Reduction Mpeg FilterPage Page Runco CL-810 Owner’s Operating Manual