TechniSat DigiCorder S1 Manual timer programming, Programme change timer, Source, Date, Start

Page 37

order to prevent an accidental premature interruption of the recording. When the receiver is in standby mode, an active timer will be indicated by a clock symbol shown on the display.

3. Programme change timer

If your receiver is in normal operating mode, it will switch to the pre-selected programme slot at the designated starting time. In contrast to the hard drive or video recorder timers, the full functionality of the unit is not restricted, and the unit will not be switched off at the end of the programme.

Manual timer programming

>Press the Menu key to call up the Main Menu.

>Use the up/down arrow keys to mark the line Timer organizing.

>Confirm by pressing OK.

The sub-menu Timer organizing will be displayed. (Fig. 7-23)

>Use the up/down arrow keys to select the type of timer you wish to programme.

>Press OK. A new window will be displayed, allowing you to enter the programming data for a new timer event. (Fig. 7-24)

To prgramme an event proceed as follows:

Source

>Use the arrow keys to mark the column Source.

>Press OK.

>A selection window will be displayed. Use the up/down arrow keys to select the desired source (TV or Radio).

>Confirm by pressing OK.

Depending on the previous setting, either the TV or the radio programme list will now be displayed.

>Use the arrow keys to mark the desired programme.

>Use the up/down arrow keys to move the marker around the list one line at a time.

>Use the left/right arrow keys to move back-ward or forward in the list one page at a time.

>Press OK to accept the selected programme into the timer.

Date

>Use the arrow keys to mark the column Date.

>Use the numeric keys to enter the date (4 digit form) of the timer event.

Start

>Use the arrow keys to mark the column Start.

>In this line, use the numeric keys to enter the starting time for the timer.

(Fig. 7-23)

(Fig. 7-24)

37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents DiSEqC DigiCorder S1Contents Changing basic programming Operating a rotating antenna DiSEqC 1.2 Illustrations Remote control unitVideo Sehr geehrte Kundin, sehr geehrter Kunde Important notes on operating the unit Please read this firstDisposal information Safety notesTemporary disconnection HelpVCR Connecting the DVB receiver to a satellite InstallationSingle unit operation ConnectionsConnection to a television set Via Scart cableVideo cassette recorder VCR Via HF cableHiFi Amplifier Analogue Digital Initial installationUnit with S-Video input Hosiden Serial Interface RSAntenna configuration Country settingDiSEqC Position A/Option aUpdating software Position B/Option BScanning for programmes When the scan is completed SettingsExiting from the installation assistant Operating languageRemote control code Basic settingsTime difference GMT hours CountryLanguage Audio signal Audio/Video settingsTV Scart mode Picture format TV setDolby Digital AC3 Video systemUHF output channel Switching DiSEqC on and off Antenna settingsSetting the switching matrix Additional settings/LNC characteristics Operation Switching on and offRotary antenna Using the numeric keys Programme selection Using the programme up/down keysUsing the Navigator Programme list Selecting a listInformation box Accessing blocked programmesReception of encrypted programmes Multifeed options Special functionsSelecting a starting time Dolby Digital AC3 mode Volume controlSelecting another language Revert to last programme selected TV/Radio switchingDisplay time and programme information Additional programme informationUsing the internal video text decoder Teletext Using the teletext decoder of your television setTransponder information Freeze frameStop mode Mixed modeSub-titles Electronic Programme Guide SFI SiehFern InfoAccessing electronic programme guide Interrupting download procedureDownloading SFI data Next Now table with current programme contentsMore Press the red function key Timer to open a selection window SFI timer programmingSFI functions SFI InfoSFI overview by programme type genre SFI programme overviewExiting from SFI Timer-controlled recordingHard drive operation RecordingOption Instant recording Start and end recording manuallyHard drive timer Timer recordingsVideo recorder timer Starting a recording manually and ending it auto MaticallyProgramme change timer Manual timer programmingSource DateChanging timer programming Timer overviewStop RepeatProgramming a new timer event Deleting timer programmingTimeshift function Press the green function key DeletePlaying hard drive recordings PlayTime Fast forward and Reverse Pause/Freeze frameEnding Play Managing the hard driveHard drive information Managing recordingsHard drive management DeleteConfiguring the Favourites list Sleep timerChanging basic programming Providers Calling up programme list managementPress the blue function key Functions Adding programmes to the Favourites listMarking blocks of programmes Use the left/right arrow keys to select Yes or NoSorting programmes Deleting from the Total listPress the blue function key Functions. a window will Now pres the yellow function key Sort. a doubleSelecting a programme Programming the electronic programme guideSFI channel Start categoryChanging the unit PIN Parental controlFunction key ModeAutomatic scan Programme scanTransponder scan Satellite scanPress the red function key Start scan SatelliteManual scan Scan modeAfter the scan Service settings Service settingsSorted UnsortedActivate default setting Activate default settingDelete all programmes Updating softwareSystem configuration Copying the settingsEncryption system Manual initialising of the CI moduleEastern and Western limits Operating a rotary antenna installation DiSEqCDeleting existing limits LNC testSet Eastern limit Setting Western limitGeo positioning Delete limNow press the arrow key left Setting a satellite positionFirst decimal point LatSetting user-defined satellite positions User satellite Test transponder/LNC configuration Adjusting the satellite antennaManual adjustment of antenna Automatic fine adjustment AutofocusCurrent satellite list Saving a satellite positionSelecting a satellite position Orbital position xx found. Save satellite ? FigDelete satellite position Technical TermsReference position Frequency range FrequencyCo-axial cable LNB/LNC Low Noise block converterService voltage Software updateReceiver see satellite receiver Satellite Satellite receiverDBS tuner Technical dataDemultiplexing Common Interface PLL modulator Antenna input Antenna outputOutput digital LNC power supplyVideo parameters Output TeletextRemote control system RC-5 TimerPower supply Mains adapter Power requirement Programme memory/satellite positionsProblem Possible cause Solution Troubleshooting guideNeously, and keep them Town/city Geogr. longitude E Geogr. latitude N Annexu Co-ordinates of some German cities1Town/city Geogr.longitude E Geogr. latitude N Co-ordinates of some German citiesAC3 IndexSFI Page For everyday operation Using the programme list34203

DigiCorder S1 specifications

The TechniSat DigiCorder S1 is a versatile and feature-rich digital video recorder (DVR) designed for users seeking high-quality television viewing experiences. Launched as a part of TechniSat’s array of premium electronic devices, the DigiCorder S1 stands out due to its array of technological advancements and user-friendly features.

One of the key features of the DigiCorder S1 is its ability to record television programs in high definition, ensuring that users can enjoy crystal-clear visuals. With a built-in hard drive that typically ranges from 160 GB to 320 GB, it offers ample storage space for users to save their favorite shows and movies. The unit employs advanced compression technologies that maximize recording capacity while maintaining image quality.

The device supports various broadcasting standards, including both DVB-S2 for satellite and DVB-T/DVB-T2 for terrestrial signals. This versatility enables users to select the best source available for high-quality content. The twin-tuner feature allows users to record one program while watching another, enhancing multifunctional capability and improving overall user satisfaction.

Connectivity options on the DigiCorder S1 are extensive, including HDMI for high-quality video output, USB ports for connection to external storage devices, and Ethernet for internet and network connectivity. This allows users to access various streaming services and online content, further expanding the entertainment possibilities.

The user interface is designed to be intuitive, making it easy to navigate through menus and set up recordings. The electronic program guide (EPG) simplifies the process of finding programs, while a timer-recording function ensures users never miss their favorite shows. Advanced features such as series recording and one-touch recording add convenience to the viewing experience.

Additionally, the TechniSat DigiCorder S1 is equipped with versatile playback features. Users can pause, rewind, and fast-forward through live television or recorded content, providing a customized viewing experience.

In conclusion, the TechniSat DigiCorder S1 is not just a digital video recorder but a comprehensive entertainment hub equipped with advanced features, making it a valuable addition to any home entertainment system. From high-definition recordings to seamless connectivity, the DigiCorder S1 delivers a complete solution for modern viewing habits. Whether watching live broadcasts or enjoying recorded content, this device ensures users have the best possible television experience.
Top Page Image Contents