TechniSat DigiCorder S1 manual Setting a satellite position, Now press the arrow key left, Lat

Page 59

longitude.

>Now press the arrow key left.

>In this field, use the OK key to indicate whether you are referring to longitude East (East) or west (W).

>Now use the arrow keys to mark the field for entering the geographical latitude.

>Use the numeric keys to enter the geographical lat- itude.

>Now press the arrow key left.

>In this field, use the OK key to indicate whether you are referring to latitude North (N) or South (S).

>Use the Back key to return to the LNC settings.

The data relating to your location must be entered as a decimal figure, correct to one decimal point. As the co-ordin- ates are frequently stated in terms of degrees, minutes and seconds, these must be converted to decimal values as follows:

The full degree figures remain unchanged by the calculation. The minutes are divided by 60, and rounded to one decimal point. The result of this division is added to the degree figure. The seconds are not considered at all, as they do not affect

the first decimal point.

 

 

 

 

Example: co-ordinates of Daun/Germany

 

 

Latitude

 

 

50°

11‘

(45“)

N

Longitude

 

06°

50‘

(10‘‘)

E

Conversion of the latitude (Lat):

 

 

Lat

=

50

+

11/60

 

 

Lat

=

50

+

0,2

(rounded)

 

Lat

=

50,2

 

 

 

 

In the menu you will enter the value, rounded to one decimal point, for geographical latitude (50,2).

The decimal value for the longitude will be calculated in the same way.

9.3 Setting a satellite position

For each satellite position to be included, work through the procedures described in Points 9.3.1 to 9.3.3. When pro- gramming satellite positions, it is recommended that you begin with the most easterly satellite location. Then, continue by adding the other satellite positions, working in a westerly direction, until you have reached the most westerly satellite position. Your digital receiver has been pre-programmed at the factory for the most commonly used satellite positions. In addition, you may enter and configure user-defined (User) satellite positions (User 1 to User 14) for any orbital position.

59

Page 58 Page 60
Image 59
Page 58 Page 60
Contents DiSEqC DigiCorder S1Contents Changing basic programming Operating a rotating antenna DiSEqC 1.2 Illustrations Remote control unitVideo Sehr geehrte Kundin, sehr geehrter Kunde Important notes on operating the unit Please read this firstHelp Safety notesDisposal information Temporary disconnectionVCR Connecting the DVB receiver to a satellite InstallationVia Scart cable ConnectionsSingle unit operation Connection to a television setHiFi Amplifier Analogue Via HF cableVideo cassette recorder VCR Serial Interface RS Initial installationDigital Unit with S-Video input HosidenPosition A/Option a Country settingAntenna configuration DiSEqCScanning for programmes Position B/Option BUpdating software Operating language SettingsWhen the scan is completed Exiting from the installation assistantCountry Basic settingsRemote control code Time difference GMT hoursPicture format TV set Audio/Video settingsLanguage Audio signal TV Scart modeUHF output channel Video systemDolby Digital AC3 Setting the switching matrix Antenna settingsSwitching DiSEqC on and off Additional settings/LNC characteristics Rotary antenna Switching on and offOperation Selecting a list Programme selection Using the programme up/down keysUsing the numeric keys Using the Navigator Programme listReception of encrypted programmes Accessing blocked programmesInformation box Selecting a starting time Special functionsMultifeed options Selecting another language Volume controlDolby Digital AC3 mode Additional programme information TV/Radio switchingRevert to last programme selected Display time and programme informationFreeze frame Teletext Using the teletext decoder of your television setUsing the internal video text decoder Transponder informationElectronic Programme Guide SFI SiehFern Info Mixed modeStop mode Sub-titlesDownloading SFI data Interrupting download procedureAccessing electronic programme guide More Now table with current programme contentsNext SFI Info SFI timer programmingPress the red function key Timer to open a selection window SFI functionsSFI overview by programme type genre SFI programme overviewRecording Timer-controlled recordingExiting from SFI Hard drive operationOption Instant recording Start and end recording manuallyStarting a recording manually and ending it auto Matically Timer recordingsHard drive timer Video recorder timerDate Manual timer programmingProgramme change timer SourceRepeat Timer overviewChanging timer programming StopPress the green function key Delete Deleting timer programmingProgramming a new timer event Timeshift functionTime PlayPlaying hard drive recordings Managing the hard drive Pause/Freeze frameFast forward and Reverse Ending PlayDelete Managing recordingsHard drive information Hard drive managementChanging basic programming Sleep timerConfiguring the Favourites list Providers Calling up programme list managementUse the left/right arrow keys to select Yes or No Adding programmes to the Favourites listPress the blue function key Functions Marking blocks of programmesNow pres the yellow function key Sort. a double Deleting from the Total listSorting programmes Press the blue function key Functions. a window willSelecting a programme Programming the electronic programme guideSFI channel Start categoryChanging the unit PIN Parental controlFunction key ModeAutomatic scan Programme scanSatellite Satellite scanTransponder scan Press the red function key Start scanAfter the scan Scan modeManual scan Unsorted Service settingsService settings SortedUpdating software Activate default settingActivate default setting Delete all programmesManual initialising of the CI module Copying the settingsSystem configuration Encryption systemLNC test Operating a rotary antenna installation DiSEqCEastern and Western limits Deleting existing limitsDelete lim Setting Western limitSet Eastern limit Geo positioningLat Setting a satellite positionNow press the arrow key left First decimal pointSetting user-defined satellite positions User satellite Automatic fine adjustment Autofocus Adjusting the satellite antennaTest transponder/LNC configuration Manual adjustment of antennaOrbital position xx found. Save satellite ? Fig Saving a satellite positionCurrent satellite list Selecting a satellite positionReference position Technical TermsDelete satellite position LNB/LNC Low Noise block converter FrequencyFrequency range Co-axial cableSatellite receiver Software updateService voltage Receiver see satellite receiver SatellitePLL modulator Antenna input Antenna output Technical dataDBS tuner Demultiplexing Common InterfaceTeletext LNC power supplyOutput digital Video parameters OutputProgramme memory/satellite positions TimerRemote control system RC-5 Power supply Mains adapter Power requirementProblem Possible cause Solution Troubleshooting guideNeously, and keep them Town/city Geogr. longitude E Geogr. latitude N Annexu Co-ordinates of some German cities1Town/city Geogr.longitude E Geogr. latitude N Co-ordinates of some German citiesAC3 IndexSFI Page For everyday operation Using the programme list34203

DigiCorder S1 specifications

The TechniSat DigiCorder S1 is a versatile and feature-rich digital video recorder (DVR) designed for users seeking high-quality television viewing experiences. Launched as a part of TechniSat’s array of premium electronic devices, the DigiCorder S1 stands out due to its array of technological advancements and user-friendly features.

One of the key features of the DigiCorder S1 is its ability to record television programs in high definition, ensuring that users can enjoy crystal-clear visuals. With a built-in hard drive that typically ranges from 160 GB to 320 GB, it offers ample storage space for users to save their favorite shows and movies. The unit employs advanced compression technologies that maximize recording capacity while maintaining image quality.

The device supports various broadcasting standards, including both DVB-S2 for satellite and DVB-T/DVB-T2 for terrestrial signals. This versatility enables users to select the best source available for high-quality content. The twin-tuner feature allows users to record one program while watching another, enhancing multifunctional capability and improving overall user satisfaction.

Connectivity options on the DigiCorder S1 are extensive, including HDMI for high-quality video output, USB ports for connection to external storage devices, and Ethernet for internet and network connectivity. This allows users to access various streaming services and online content, further expanding the entertainment possibilities.

The user interface is designed to be intuitive, making it easy to navigate through menus and set up recordings. The electronic program guide (EPG) simplifies the process of finding programs, while a timer-recording function ensures users never miss their favorite shows. Advanced features such as series recording and one-touch recording add convenience to the viewing experience.

Additionally, the TechniSat DigiCorder S1 is equipped with versatile playback features. Users can pause, rewind, and fast-forward through live television or recorded content, providing a customized viewing experience.

In conclusion, the TechniSat DigiCorder S1 is not just a digital video recorder but a comprehensive entertainment hub equipped with advanced features, making it a valuable addition to any home entertainment system. From high-definition recordings to seamless connectivity, the DigiCorder S1 delivers a complete solution for modern viewing habits. Whether watching live broadcasts or enjoying recorded content, this device ensures users have the best possible television experience.
Top Page Image Contents