TechniSat DigiCorder S1 Changing basic programming, Sleep timer, Configuring the Favourites list

Page 43

Monitoring the hard drive

>To monitor the hard drive, use the left/right arrow keys to mark the field Check.

>Press OK, then confirm the screen prompt displayed by pressing OK again to start the checking procedure. The status of the hard drive will now be chec-

ked, the result will be displayed on screen.

Formating the hard drive

When the hard drive is formatted, the data system is replaced. This may become necessary if checking the hard drive reveals faults or problems.

Note!

The hard drive contents are deleted completely during formating, all existing recordings will be lost.

>To format the hard drive, use the left/right arrow keys to mark the field Format.

>Press OK and confirm the following screen prompt by pressing OK again in order to start the formating pro-

cedure.

Please note !

The receiver may be operated only with the built-in hard drive. Any other drive may damage the unit.

You should therefore not open the unit case, and replacement of the hard drive would invalidate all terms of the guarantee.

7.16 Sleep timer

>Press the Sleep timer key repeatedly to set the switch-off time of the receiver from 30 minutes to 2 hours in 30 minute steps.

When the set time has elapsed the receiver will auto- matically switch to standby mode.

8 Changing basic programming

8.1 Configuring the Favourites list

This chapter describes how you can change the pre-program- ming of your digital receiver, as well as the Favourites list in line with your preferences. This function is also required to sort newly found programmes into the list after a programme scan.

You should note that your receiver is equipped with two pro- gramme lists, the Favourites list and the Total list. The Favourites programme list includes all programmes you have included in the list, following the procedure described below. The Total list includes all programmes.

This chapter also describes how programmes can be deleted, how access can be blocked by means of the parental control

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents DiSEqC DigiCorder S1Contents Changing basic programming Operating a rotating antenna DiSEqC 1.2 Illustrations Remote control unitVideo Sehr geehrte Kundin, sehr geehrter Kunde Important notes on operating the unit Please read this firstHelp Safety notesDisposal information Temporary disconnectionVCR Connecting the DVB receiver to a satellite InstallationVia Scart cable ConnectionsSingle unit operation Connection to a television setVideo cassette recorder VCR Via HF cableHiFi Amplifier Analogue Serial Interface RS Initial installationDigital Unit with S-Video input HosidenPosition A/Option a Country settingAntenna configuration DiSEqCUpdating software Position B/Option BScanning for programmes Operating language SettingsWhen the scan is completed Exiting from the installation assistantCountry Basic settingsRemote control code Time difference GMT hoursPicture format TV set Audio/Video settingsLanguage Audio signal TV Scart modeDolby Digital AC3 Video systemUHF output channel Switching DiSEqC on and off Antenna settingsSetting the switching matrix Additional settings/LNC characteristics Operation Switching on and offRotary antenna Selecting a list Programme selection Using the programme up/down keysUsing the numeric keys Using the Navigator Programme listInformation box Accessing blocked programmesReception of encrypted programmes Multifeed options Special functionsSelecting a starting time Dolby Digital AC3 mode Volume controlSelecting another language Additional programme information TV/Radio switchingRevert to last programme selected Display time and programme informationFreeze frame Teletext Using the teletext decoder of your television setUsing the internal video text decoder Transponder informationElectronic Programme Guide SFI SiehFern Info Mixed modeStop mode Sub-titlesAccessing electronic programme guide Interrupting download procedureDownloading SFI data Next Now table with current programme contentsMore SFI Info SFI timer programmingPress the red function key Timer to open a selection window SFI functionsSFI overview by programme type genre SFI programme overviewRecording Timer-controlled recordingExiting from SFI Hard drive operationOption Instant recording Start and end recording manuallyStarting a recording manually and ending it auto Matically Timer recordingsHard drive timer Video recorder timerDate Manual timer programmingProgramme change timer SourceRepeat Timer overviewChanging timer programming StopPress the green function key Delete Deleting timer programmingProgramming a new timer event Timeshift functionPlaying hard drive recordings PlayTime Managing the hard drive Pause/Freeze frameFast forward and Reverse Ending PlayDelete Managing recordingsHard drive information Hard drive managementConfiguring the Favourites list Sleep timerChanging basic programming Providers Calling up programme list managementUse the left/right arrow keys to select Yes or No Adding programmes to the Favourites listPress the blue function key Functions Marking blocks of programmesNow pres the yellow function key Sort. a double Deleting from the Total listSorting programmes Press the blue function key Functions. a window willSelecting a programme Programming the electronic programme guideSFI channel Start categoryChanging the unit PIN Parental controlFunction key ModeAutomatic scan Programme scanSatellite Satellite scanTransponder scan Press the red function key Start scanManual scan Scan modeAfter the scan Unsorted Service settingsService settings SortedUpdating software Activate default settingActivate default setting Delete all programmesManual initialising of the CI module Copying the settingsSystem configuration Encryption systemLNC test Operating a rotary antenna installation DiSEqCEastern and Western limits Deleting existing limitsDelete lim Setting Western limitSet Eastern limit Geo positioningLat Setting a satellite positionNow press the arrow key left First decimal pointSetting user-defined satellite positions User satellite Automatic fine adjustment Autofocus Adjusting the satellite antennaTest transponder/LNC configuration Manual adjustment of antennaOrbital position xx found. Save satellite ? Fig Saving a satellite positionCurrent satellite list Selecting a satellite positionDelete satellite position Technical TermsReference position LNB/LNC Low Noise block converter FrequencyFrequency range Co-axial cableSatellite receiver Software updateService voltage Receiver see satellite receiver SatellitePLL modulator Antenna input Antenna output Technical dataDBS tuner Demultiplexing Common InterfaceTeletext LNC power supplyOutput digital Video parameters OutputProgramme memory/satellite positions TimerRemote control system RC-5 Power supply Mains adapter Power requirementProblem Possible cause Solution Troubleshooting guideNeously, and keep them Town/city Geogr. longitude E Geogr. latitude N Annexu Co-ordinates of some German cities1Town/city Geogr.longitude E Geogr. latitude N Co-ordinates of some German citiesAC3 IndexSFI Page For everyday operation Using the programme list34203

DigiCorder S1 specifications

The TechniSat DigiCorder S1 is a versatile and feature-rich digital video recorder (DVR) designed for users seeking high-quality television viewing experiences. Launched as a part of TechniSat’s array of premium electronic devices, the DigiCorder S1 stands out due to its array of technological advancements and user-friendly features.

One of the key features of the DigiCorder S1 is its ability to record television programs in high definition, ensuring that users can enjoy crystal-clear visuals. With a built-in hard drive that typically ranges from 160 GB to 320 GB, it offers ample storage space for users to save their favorite shows and movies. The unit employs advanced compression technologies that maximize recording capacity while maintaining image quality.

The device supports various broadcasting standards, including both DVB-S2 for satellite and DVB-T/DVB-T2 for terrestrial signals. This versatility enables users to select the best source available for high-quality content. The twin-tuner feature allows users to record one program while watching another, enhancing multifunctional capability and improving overall user satisfaction.

Connectivity options on the DigiCorder S1 are extensive, including HDMI for high-quality video output, USB ports for connection to external storage devices, and Ethernet for internet and network connectivity. This allows users to access various streaming services and online content, further expanding the entertainment possibilities.

The user interface is designed to be intuitive, making it easy to navigate through menus and set up recordings. The electronic program guide (EPG) simplifies the process of finding programs, while a timer-recording function ensures users never miss their favorite shows. Advanced features such as series recording and one-touch recording add convenience to the viewing experience.

Additionally, the TechniSat DigiCorder S1 is equipped with versatile playback features. Users can pause, rewind, and fast-forward through live television or recorded content, providing a customized viewing experience.

In conclusion, the TechniSat DigiCorder S1 is not just a digital video recorder but a comprehensive entertainment hub equipped with advanced features, making it a valuable addition to any home entertainment system. From high-definition recordings to seamless connectivity, the DigiCorder S1 delivers a complete solution for modern viewing habits. Whether watching live broadcasts or enjoying recorded content, this device ensures users have the best possible television experience.
Top Page Image Contents