Panasonic AJ-D850P manual RS-232C Remote 25-pin D-SUB crossover cable supported

Page 100

Connector signals

PARALLEL REMOTE (25P)

Pin No.	Signal	Pin No.	Signal	Pin No.	Signal

1	PLAY COMMAND	10	—————	19	STAND BY ON STATUS

2	STOP COMMAND	11	—————	20	PREROLL STATUS

3	FF COMMAND	12	≥10V, MAX 300mA	21	SERVO LOCK STATUS

4	REW COMMAND	13	PLAY STATUS	22	OPERATION ENABLE STATUS

5	REC COMMAND	14	STOP STATUS	23	—————

6	EJECT COMMAND	15	FF STATUS	24	—————

7	STAND BY COMMAND	16	REW STATUS	25	GND

8	PREROLL COMMAND	17	REC STATUS

9	IN SET COMMAND	18	EJECT STATUS

<Notes>

•COMMAND pins: TTL level, active low, ≥100ms edge electrical signal.

•STATUS pins: open collector, sink current 6 mA

RS-232C REMOTE (25-pin D-SUB crossover cable supported)

	Pin No.	Abbreviation	Circuit	Description

	1	FRAME GROUND	Protective ground	Frame ground

	2	RxD	Received data	Sends data to the PC.

	3	TxD	Transmitted data	Receives data from the PC.

	4	CTS	Clear to send	Shorted with pin 5.

	5	RTS	Request to send	Shorted with pin 4.

	6	DTR	Data terminal ready	No processing

	7	GND	Signal ground	Signal ground

	20	DSR	Data set ready	Positive power output after communication
	20	DSR	Data set ready	enable status
				enable status

ENCODER REMOTE (15P)

Pin No.	Signal	Pin No.	Signal	Pin No.	Signal

1	—————	6	SYSTEM H 0	11	RET GND

2	SET UP	7	SYS.SC COARSE (2)	12	—————

3	C LEVEL	8	–12V	13	—————

4	GND	9	HUE	14	SYS.SC FINE

5	+12V	10	VIDEO LEVEL	15	SYS.SC COARSE (1)

– 100 –

Image 100

Contents Operating Instructions FCC Note Do not OpenContents General and Features FeaturesMenu-driven setup Recording and playing back V blanking dataTime codes Multi-function input/output interfacesFront panel Controls and their functionsFront Panel Top Section Input Select display Cassette insertion slotEject button Channel condition lampsFront Panel Center Section 8TC/CTL switch 9TC/UB switch@0INT/EXT switch @1TAPE/EE switch In the stop mode@2REMOTE/LOCAL switch @6SHTL/SLOW switch@3REMOTE lamp @4Search button@9PREROLL button #0AUTO Edit button#1PREVIEW/REVIEW buttons #2IN a IN/SET/OUT a OUT buttons$5Headphones jack #7Time code buttons#8Warning lamp #9Cassette insertion display lamp$7MONITOR Select switches $6Volume control$8METER FULL/FINE selector switch Front Panel Bottom Section 7REC Inhibit switch 8MENU button9SET button 0DIAG buttonConnector area AC in connector Signal GND terminalAnalog Audio in connectors CUE in connector5ANALOG Component Video OUT connector 6ANALOG Composite Video OUT connectors7DIGITAL Audio IN/OUT connector 9Remote control connectorsAnalog audio input connectors Reference input connectors Connections when one unit is usedInput connector Connections when 2 units are used deck to deck Remote control signal 9PDigital audio Analog video signal component RecorderConnections with editing controller Switcher Player Source machineMake these two WFM VSCTapes Type DescriptionConsumer CassetteSwitching on the power/inserting the cassette STOP/STAND by mode Still Timer SettingSelecting video/audio input signals 2Adjusting the video level3Adjusting the audio level RecordingPlayback Shuttle mode Jog modeJog/shuttle Manual editing Preroll Automatic editing Deck to Deck Switch settings and adjustments When the unit is used as the recorderWhen the unit is used as the player Automatic editingSelect the editing mode Match frame processing function Entering the edit pointsNegative duration function Checking the edit points Calculating the duration2Resetting either the edit in or OUT point 1Resetting both the edit in and OUT pointsModifying the edit points Preview Executing automatic editing PostrollRetry function Auto tag editingReview Split editing Audio split editing Entering the edit pointsDeleting the edit points Modifying the edit pointsDisplaying the audio split edit points Cueing up the tape to the edit pointsDuration display OperationsOperating procedure Voice-over facility internalStop For operation with an editing controller AG-A850 VTRAudio cross channel editing internal Example To record cross-faded audio signals onto CH2Connections Page Teletext signal recording/playback function Mode Additional lines Teletext signalsBlanking data recording/playback Additional line recording/playback functionVideo output encoder output signal adjustments Setup levelVideo level Chroma level and hueChanging the settings Setup default settingsSETUP-MENU Init SET YESPLAY/NOSTOP Setup setting menus Changing the fileSetup menus Setting and releasing the lock modeLoading a user file USER1Automatic loading of user file when the power is turned on Saving a user fileSetting Description System menuSystem DisplaySystem Setting Description User menu BasicBasic Setting Description Operation Operation Memory stop functionEE Mode FRZ ModeNormal RespnsInterface Edit Edit Setting Description VAR REV JOG StepJOG FWD JOG REVAUD MEM ModeAmux AmuvoTape Protect Time CodeDF Mode BlankTCG TC&UBTime Code VideoSBC sub code data area Vaux video auxiliary data areaVideo Setting Description Audio Audio Setting Description DV PB ATT Moni SELINH CUE SlowBlank Blank Setting Description Line 10&273 0000 Menu Time code/user bit Time codeUser bit TCR 00 07 04 Frames Hours Seconds MinutesSetting the internal time code Setting the external time code TC switch → EXTRecording internal/external time codes Time codeReproducing the time code/user bit Operation mode Superimpose screenCharacters displayed Display positionWhat is the Servo REF on the setup menu No setting? Is the REF Video signal supplied?Is the input video signal available? Servo referenceDuring playback or special playback Servo reference setting tablesDuring recording or editing Audio V Fade Function Printed circuit board CUERack mounting Inner memberVideo head cleaning CondensationDiag menu Error messagesDisplaying the Diag menu Displaying the Hours Meter information Item No DescriptionPriority Display Description Priority Monitor display Description VTR operationTable of Auto OFF Error messages Power OFF→ONCounter display Monitor display Description VTR operation Restart conditionServo Control Hardware specifications External interface specificationsRS-232C interface IntroductionSoftware specifications ProtocolError code table When the communication has terminated abnormally NackReturn format VTR → controller PC ACK STX OPL ETXCommand table Commands relating to operation control NotesSTX OSR ETX ReverseStandby STX OBF ETX Standby STX OBN ETXCommands relating to inquiries Notes Microsoft QuickBASIC sample program CLSConnector signals Pin No. SignalSignal Pin No SignalRS-232C Remote 25-pin D-SUB crossover cable supported Pin No Abbreviation Circuit DescriptionSpecifications Other input/output connectorParts Information & Ordering