Panasonic AJ-D850P manual Rack mounting, Inner member

Page 86

Rack mounting

The unit can be mounted into a 19-inch standard rack if the optional rack-mounting adaptors (AJ-MA75P) are used. For the installation rails, it is recommended that the rail and bracket for 18" length (model number CC3001-99-0400) of CHASSIS TRAK be used. (The complete slide rail and bracket unit is not available from Panasonic) For further details, consult with your dealer.

1

2

Remove the screws on the left and right sides of the unit.

Use the removed screw to attach the inner members of the slide rails.

3

4

5

Inner member

The length of the screws used is subject to restriction. If some of the mounting screws have been lost or misplaced, use screws which are less than 0.4" long in their place. Use four screws to secure each inner member.

Attach the outer member brackets to the rack.

Check that the height is the same for the left and right brackets.

Attach the AJ-MA75P rack-mounting adaptors with included 4 screws.

Remove the 4 rubber legs from the bottom of the unit, and install the unit in the rack. After the unit has been installed, check that it moves smoothly along the rails.

EIA Standard rack

Fasten it to the rack with set screws.

<Notes>

Keep the temperature inside the rack to between +41°F (5°C) and +104°F (40°C).

Bolt the rack securely to the floor so that it will not topple over when the VTR is drawn out.

– 86 –

Image 86
Contents Operating Instructions FCC Note Do not OpenContents General and Features FeaturesTime codes Menu-driven setupRecording and playing back V blanking data Multi-function input/output interfacesFront Panel Top Section Controls and their functionsFront panel Eject button Input Select displayCassette insertion slot Channel condition lampsFront Panel Center Section @0INT/EXT switch 8TC/CTL switch9TC/UB switch @1TAPE/EE switch In the stop mode@3REMOTE lamp @2REMOTE/LOCAL switch@6SHTL/SLOW switch @4Search button#1PREVIEW/REVIEW buttons @9PREROLL button#0AUTO Edit button #2IN a IN/SET/OUT a OUT buttons#8Warning lamp $5Headphones jack#7Time code buttons #9Cassette insertion display lamp$8METER FULL/FINE selector switch $6Volume control$7MONITOR Select switches Front Panel Bottom Section 9SET button 7REC Inhibit switch8MENU button 0DIAG buttonConnector area Analog Audio in connectors AC in connectorSignal GND terminal CUE in connector7DIGITAL Audio IN/OUT connector 5ANALOG Component Video OUT connector6ANALOG Composite Video OUT connectors 9Remote control connectorsInput connector Connections when one unit is usedAnalog audio input connectors Reference input connectors Digital audio Analog video signal component Connections when 2 units are used deck to deckRemote control signal 9P RecorderConnections with editing controller Make these two SwitcherPlayer Source machine WFM VSCConsumer TapesType Description CassetteSwitching on the power/inserting the cassette STOP/STAND by mode Still Timer Setting3Adjusting the audio level Selecting video/audio input signals2Adjusting the video level RecordingPlayback Jog/shuttle Jog modeShuttle mode Manual editing Preroll Automatic editing Deck to Deck When the unit is used as the player Switch settings and adjustmentsWhen the unit is used as the recorder Automatic editingSelect the editing mode Negative duration function Entering the edit pointsMatch frame processing function Checking the edit points Calculating the durationModifying the edit points 1Resetting both the edit in and OUT points2Resetting either the edit in or OUT point Preview Retry function Executing automatic editingPostroll Auto tag editingReview Split editing Deleting the edit points Audio split editingEntering the edit points Modifying the edit pointsDuration display Displaying the audio split edit pointsCueing up the tape to the edit points OperationsOperating procedure Voice-over facility internalStop For operation with an editing controller AG-A850 VTRConnections Example To record cross-faded audio signals onto CH2Audio cross channel editing internal Page Blanking data recording/playback Teletext signal recording/playback functionMode Additional lines Teletext signals Additional line recording/playback functionVideo level Video output encoder output signal adjustmentsSetup level Chroma level and hueSETUP-MENU Init SET YESPLAY/NOSTOP Setup default settingsChanging the settings Setup setting menus Changing the fileSetup menus Setting and releasing the lock modeLoading a user file USER1Automatic loading of user file when the power is turned on Saving a user fileSystem Setting DescriptionSystem menu DisplaySystem Setting Description User menu BasicBasic Setting Description Operation Operation Memory stop functionNormal EE ModeFRZ Mode RespnsInterface Edit Edit Setting Description JOG FWD VAR REVJOG Step JOG REVAmux AUD MEMMode AmuvoTape Protect Time CodeTCG DF ModeBlank TC&UBSBC sub code data area Time CodeVideo Vaux video auxiliary data areaVideo Setting Description Audio Audio Setting Description INH DV PB ATTMoni SEL CUE SlowBlank Blank Setting Description Line 10&273 0000 Menu User bit Time code/user bitTime code TCR 00 07 04 Frames Hours Seconds MinutesRecording internal/external time codes Setting the internal time codeSetting the external time code TC switch → EXT Time codeReproducing the time code/user bit Characters displayed Operation modeSuperimpose screen Display positionIs the input video signal available? What is the Servo REF on the setup menu No setting?Is the REF Video signal supplied? Servo referenceDuring recording or editing Servo reference setting tablesDuring playback or special playback Audio V Fade Function Printed circuit board CUERack mounting Inner memberVideo head cleaning CondensationDisplaying the Diag menu Error messagesDiag menu Priority Display Description Displaying the Hours Meter informationItem No Description Priority Monitor display Description VTR operationCounter display Monitor display Description VTR operation Table of Auto OFF Error messagesPower OFF→ON Restart conditionServo Control RS-232C interface Hardware specificationsExternal interface specifications IntroductionSoftware specifications ProtocolReturn format VTR → controller PC Error code tableWhen the communication has terminated abnormally Nack ACK STX OPL ETXCommand table Commands relating to operation control NotesStandby STX OBF ETX STX OSR ETXReverse Standby STX OBN ETXCommands relating to inquiries Notes Microsoft QuickBASIC sample program CLSSignal Connector signalsPin No. Signal Pin No SignalRS-232C Remote 25-pin D-SUB crossover cable supported Pin No Abbreviation Circuit DescriptionSpecifications Other input/output connectorParts Information & Ordering