JVC HR-J765EK setup guide Video Plus+ Timer Programming

Page 12

12BASICOPERATIONS(cont.)

VIDEO Plus+

Timer

Programming

Before performing VIDEO Plus+ Timer Programming:

●Make sure that the recorder's built-in clock is set properly.

●Insert a cassette with the safety tab in place. The recorder will come on automatically.

●Turn on the TV and select the VIDEO channel (or AV mode).

With VIDEO Plus+, timer programming is greatly simplified because each TV programme has a corresponding code number which your recorder is able to recognise.

ACCESS VIDEO PLUS+ SCREEN

1	Press PROG.	VIDEO PLUS+
	Press PROG.

		[0 – 9] =
		[+/–] : EXPRESS PROGRAMING
		[PROG] : EXIT

The front display panel looks like this:

ENTER PLUSCODE NUMBER

	Press the NUMBER keys to	VIDEO PLUS+
	enter the PlusCode	VIDEO PLUS+
	enter the PlusCode	1 2 3 4 5 6 7 8
	2 number of the programme	1 2 3 4 5 6 7 8
	2 number of the programme
	you wish to record.

2 1

NUMBER 4

5 PDC 7

STOP+/–

2

5

DAILY3

6

9

2

4

WEEKLY

7

●If you make a mistake, press and input the

correct number.	[0 – 9] =
	[ ] : DELETE
	[PROG] : EXIT

The PlusCode number you enter appears on the front display panel:

The display panel shows only a 4-digit number.

ACCESS VIDEO PLUS+ PROGRAM

1,6	PROG	1	?

	SP/LP	4
		4
3		OK 3,6

SCREEN

	Press OK, and the VIDEO				– P1 –
	Plus+ Program screen			VIDEO PLUS+ 123456789
3 appears (if you’re just				START		STOP
3 appears (if you’re just			21:00		= 22:00
	starting out, “P1” appears).			SP	VPS/PDC OFF
				SP	VPS/PDC OFF
	The display panel shows the			DATE		TV PROG
	programme start time.		25.12		1
	Pressing	changes the				BBC 1
	Pressing	changes the
	display to the programme
	display to the programme			: OK
	stop time, then the date and
	preset position.

		SP

IMPORTANT

Make sure the preset position number you wish to record is displayed; if not, see "VIDEO Plus+ Setup" on page 40 and set the Guide Program number for that PlusCode number correctly.

●If the number you entered is invalid, "ERROR" appears on the screen and "Err" appears on the display panel. Press and input a valid PlusCode number.

●If the "GUIDE PROG SET" screen appears, see "ATTENTION – Regarding Guide Program Number Set" on page 13.

Image 12

Contents HR-J765EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV Back of RecorderBefore performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Access Video PLUS+ ScreenStart Time Enter ProgrammeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Access Main Menu Access Mode SETSelect Picture Control SET Mode Adjust TrackingPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Selecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackLooking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitEngage Auto Satellite Prog REC Mode Press SP/LP on the remote control to set the tape speedBefore performing the following steps SET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Activate Repeat PlaybackRepeat Playback Ntsc PlaybackConnection To Stereo System TelevisionAudio Cable not provided Audio OUT Mains outletAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionTuner Set SETAuto Channel Set Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?Troubleshooting Cassette with the Record Safety tab Blinking Intact Blinks for 10 secondsCheck the programmed data and re Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical