JVC HR-J765EK Edit From a Camcorder, SET RECORDER’S Input Mode, Start Camcorder, Start Recorder

Page 25

Edit From A Camcorder

25

You can use a camcorder as the source player and your video recorder as the recorder.

MAKE CONNECTIONS

1 Connect the camcorder’s AUDIO/VIDEO OUT connectors to the recorder’s front panel AUDIO/VIDEO input connectors.

● When using a monaural camcorder, connect its AUDIO OUT connector to the AUDIO L input connector on your recorder.

SET RECORDER’S INPUT

MODE

1 2 3

4 5 6

7 8 9

AUX0

1

?

Recorder

2

4

TV PROG

2 Press AUX and/or TV PROG so that “F-1” appears in place of a preset position number.

SET EDIT MODE

3 See "Picture Control" on page 17.

START CAMCORDER

4 Engage its Play mode.

START RECORDER

5 Engage its Record mode.

NOTES:

●All necessary cables can be obtained from your dealer.

●When you select EDIT to dub tapes in step 3, be sure to select AUTO (or NORM when B.E.S.T. is set to OFF) after you finish dubbing the tapes.

		REW	FF
STANDBY/ON
			TV PROG/
	TIMER		JOG
VIDEO(MONO)L –AUDIO– R			SHUTTLE
VIDEO(MONO)L –AUDIO– R	REC LINK	TV PROG

VIDEO	AUDIO
input	AUDIO
input	input
	input
		Audio/Video Cable
	VIDEO OUT	(not provided)

Camcorder

AUDIO OUT

Player

Image 25

Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVYour TV via both an RF cable and a 21-pin Before performing the following procedure, make sure thatGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPAccess Video PLUS+ Screen Express Timer ProgrammingStart Time Enter ProgrammePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Access Mode SET Access Main MenuSelect Picture Control SET Mode Adjust TrackingTurn on the Recorder Playback/ Recording According To Tape Charac- teristicsS.T. Picture System Playback RecordingOr press Record on the recorder Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackActivate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitPress SP/LP on the remote control to set the tape speed Engage Auto Satellite Prog REC ModeBefore performing the following steps SET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto SP→LP Timer Select ModeAuto Timer Playback Activate RepeatRepeat Playback Ntsc PlaybackTelevision Connection To Stereo SystemAudio Cable not provided Audio OUT Mains outletExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeSET Tuner SetAuto Channel Set Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Fine-Tuning Channels Already Stored Change Station Preset PositionDelete a Channel Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Blinking Intact Blinks for 10 seconds Cassette with the Record Safety tabCheck the programmed data and re Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time