JVC HR-J765EK setup guide Video Channel Set, Access Video CHAN- NEL SET Mode, SET Video Channel

Page 30

30SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

 

 

REW

FF

STANDBY/ON

 

 

 

 

 

 

TV PROG/

 

TIMER

 

JOG

VIDEO(MONO)L –AUDIO– R

 

 

SHUTTLE

REC LINK

TV PROG

 

STOP

IMPORTANT

Perform the following steps only if —

Video Channel Set has not been done correctly by the Auto Set Up function (pg. 6).

interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

you change the connection between your recorder and TV from RF connection to AV connection, or vice versa.

If you have connected the video recorder to your TV via both an RF cable and a 21-pin SCART cable (AV connection), you do not need the video channel so you have to set the video channel to off. Go to "With AV Connection" below.

If you have connected the video recorder to your TV via an RF cable only (RF connection), you have to set the correct video channel Go to "With RF Connection" on page 31.

With AV Connection

Before performing the following procedure, make sure that:

the mains power cord is plugged into the mains outlet.

the video recorder is turned off and there is no cassette inserted in the recorder.

batteries have been installed in the remote control.

1 2 3

4 5 6

7 8 9

0

2

4

TV PROG

ACCESS VIDEO CHAN- NEL SET MODE

Press and hold down STOP on the recorder until the

1 display panel shows the following.

SET VIDEO CHANNEL

Press TV PROG – until the display panel shows

1

?

OK

2 "OUT– –".

Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 30
Contents HR-J765EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV Back of RecorderBefore performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayVideo Plus+ Timer Programming Satellite Receiver Users Timer WarningPDC Recording Press SP/LPStart Time Express Timer ProgrammingAccess Video PLUS+ Screen Enter ProgrammeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Select Picture Control SET Mode Access Main MenuAccess Mode SET Adjust TrackingPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Soundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackActivate Instant Review Looking For Scene You WantActivate Index Search Skip Over UnwantedOutdoor Unit Satellite Cable Aerial connectorAutomatic Satellite Programme Recording Satellite Receiver UnitEngage Auto Satellite Prog REC Mode Press SP/LP on the remote control to set the tape speedBefore performing the following steps Edit To Or From Another Video Recorder SET Recording DECK’S Input ModeSET Edit Mode Make ConnectionsStart Camcorder SET RECORDER’S Input ModeEdit From a Camcorder Start RecorderENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Repeat Playback Activate RepeatPlayback Ntsc PlaybackAudio Cable not provided Connection To Stereo SystemTelevision Audio OUT Mains outletVideo Channel Set Access Video CHAN- NEL SET ModeExit Video Channel SET Mode SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionTuner Set SETAuto Channel Set After Scan Completed Screen preset positionsProcedures Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Select NEW Station Access Manual Channel SET ScreenSwitch Stations Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockAccess Guide Prog SET Screen Video Plus+ SetupAccess Initial SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?Troubleshooting Cassette with the Record Safety tab Blinking Intact Blinks for 10 secondsCheck the programmed data and re Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical