JVC HR-J765EK setup guide Tuner Set, Auto Channel Set

Page 32

32SUBSIDIARYSETTINGS(cont.)

Tuner Set

Turn on the TV and select the VIDEO channel (or AV mode).

IMPORTANT

Perform the following steps only if —

—Auto Channel Set has not been set correctly by Auto Set Up function (☞ pg. 6).

—you have moved to a different area or if a new station starts broadcasting in your area.

Your recorder needs to memorise all necessary stations in preset positions in order to record TV programmes. Auto Channel Set automatically assigns all receivable stations in your area to call them up by using the TV PROG buttons without going through any vacant channel.

1 2 3

4 5 6

7 8 9

0

1

?

MENU

2

4

TV PROG

OK

Auto Channel Set

	TURN ON THE RECORDER
1 Press					.
1 Press					.
	ACCESS MAIN MENU
	SCREEN
2 Press MENU.
	PERFORM AUTO CHANNEL
3	SET
	Move the highlight					MAIN MENU
	bar (pointer) to					MAIN MENU
	"AUTO CH SET" by					AUTO CH SET
	pressing %Þ, then					MODE SET

						MANUAL CH SET
	press OK or .#					MANUAL CH SET
	press OK or .#					INITIAL SET

						[5°] =
						[MENU] : EXIT

●The Auto Set screen

appears, and				AUTO SET
remains on screen				PLEASE WAIT
while the recorder				PLEASE WAIT
while the recorder
searches for				+			+	+
receivable stations.			0
receivable stations.			0
As Auto Channel
Set progresses, the			[MENU] : EXIT
"		" mark on the
screen moves			Beginning					End
from left to right.			Beginning					End
from left to right.

Wait until the screen as shown in step 4 appears.

●Auto Channel Set usually takes about 4 – 12 minutes; the duration varies by area.

Image 32

Contents HR-J765EK Safety Precautions Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of TV Back of RecorderGo to item Before performing the following procedure, make sure thatYour TV via both an RF cable and a 21-pin Auto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Timer Warning PDC RecordingSatellite Receiver Users Press SP/LPExpress Timer Programming Access Video PLUS+ ScreenStart Time Enter ProgrammeSET PDC Mode Press TV Prog +/- toCheck, Cancel And Replace Programmes Access Main Menu Access Mode SETSelect Picture Control SET Mode Adjust TrackingS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Selecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackLooking For Scene You Want Activate Index SearchActivate Instant Review Skip Over UnwantedAerial connector Automatic Satellite Programme RecordingOutdoor Unit Satellite Cable Satellite Receiver UnitBefore performing the following steps Engage Auto Satellite Prog REC ModePress SP/LP on the remote control to set the tape speed SET Recording DECK’S Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsAuto Timer Select ModeAuto SP→LP Timer Activate Repeat PlaybackRepeat Playback Ntsc PlaybackConnection To Stereo System TelevisionAudio Cable not provided Audio OUT Mains outletAccess Video CHAN- NEL SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelAccess Video Chan NEL SET Mode With RF ConnectionAuto Channel Set Tuner SetSET Screen preset positions ProceduresAfter Scan Completed Is displayed on the screenStoring Channels Manually Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Access Manual Channel SET Screen Switch StationsSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockVideo Plus+ Setup Access Initial SET ScreenAccess Guide Prog SET Screen Enter Guide Prog NumberQuestions And Answers Remain lit on the display panel. Is there Problem?Troubleshooting Check the programmed data and re Cassette with the Record Safety tabBlinking Intact Blinks for 10 seconds Index Front ViewAudio OUT L/R Connectors enable Tape Speed Indicators display mode of recording lightRemote Control Auto Tracking Button enables/disables auto VCR, TV Prog +/-,TV +/-, TV MutingMaximum recording time DA4 Double Azimuth helical