JVC HR-J765EK setup guide Audio OUT L/R Connectors enable

Page 45

45

REAR VIEW

1

2

SORTIE

OUT

AV2 ENTREE/DECODEUR

AV1 ENTREE/SORTIE

R

IN/DECODER

IN/OUT

 

 

 

AUDIO

 

 

L

ENTREE ANT. IN

ANTENNE

SORTIE RF OUT

3

4

 

 

 

5 6

1Mains Power Cord supplies power to recorder. ☞ pg. 5

2 ANT. IN Connector enables connection of aerial. ☞ pg. 5 3 AV2 IN/DECODER Connector enables connection of satellite receiver or second recorder; input recordable

when "L-2" selected. ☞ pg. 22, 24

4 AV1 IN/OUT Connector enables AV connection to TV or second recorder; input recordable when "L-1" selected. ☞ pg. 5, 24

5AUDIO OUT (L/R) Connectors enable

connection of audio cassette recorder, TV or second

video recorder for dubbing. ☞ pg. 29

6RF. OUT Connector enables connection to aerial terminal of TV receiver. ☞ pg. 5

DISPLAY PANEL

1

2

3

45 6

7

8

 

REVIEW

 

SP

VPS/PDC

VCR

 

9

0 !

@ #

1B.E.S.T. Picture System Display lights from bottom to top while B.E.S.T. is active. ☞ pg. 18

2Symbolic Mode Indicators

 

 

STILL:

 

PLAY:

 

SLOW:

 

FF/REW VARIABLE

 

RECORD:

 

SHUTTLE SEARCH:

 

 

 

 

 

 

RECORD PAUSE:

 

 

 

 

 

 

 

 

3Tape Speed Indicators display mode of recording; light

during Record or Play mode. ☞ pg. 10

* EP is only for NTSC playback.

4Programme Time Indicators show the programme start time () and the programme stop time () for

timer-recording. ☞ pg. 14

5"Timer" Indicator lights when has been pressed to

engage Timer mode. ☞ pg. 13, 15

6Tape Remaining Time Indicator displays time remaining on tape when certain buttons are pressed. ☞ pg. 11

7Channel Display shows preset position where the station currently being received is stored.

Clock Display shows current time. ☞ pg. 7

8Instant REVIEW Indicator blinks after timer-recording and shows how many programmes have been timer-

recorded. ☞ pg. 19

9PDC Indicator lights when PDC has been engaged for timer recording. ☞ pg. 13, 15

*VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

0VCR Indicator lights when the video recorder is in the video mode. At this point, the TV automatically

enters AV mode. ☞ pg. 8

!"Cassette Loaded" Mark lights once a cassette is inserted; remains lit until cassette ejected.

@Counter shows time elapsed since playback or

recording began.

With displayed, shows time remaining from current tape position to end of tape (☞ pg. 11). Counter, Preset Position*, Clock and Tape Remaining Time Display appear alternately when – –:– – is

pressed.

*Preset Position is not displayed during playback.

#Mode shows external input mode selected (L-1, L-2 or F-1).

Page 44 Page 46
Image 45
Page 44 Page 46
Contents HR-J765EK Do not place the recorder Safety PrecautionsSome Dos And Donts On The Safe Use Of Equipment Quick SET UP G Uide Back of Recorder Back of TVBefore performing the following procedure, make sure that Your TV via both an RF cable and a 21-pinGo to item If both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming PDC Recording Timer WarningSatellite Receiver Users Press SP/LPAccess Video PLUS+ Screen Express Timer ProgrammingStart Time Enter ProgrammePress TV Prog +/- to SET PDC ModeCheck, Cancel And Replace Programmes Access Mode SET Access Main MenuSelect Picture Control SET Mode Adjust TrackingPlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Receiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackActivate Index Search Looking For Scene You WantActivate Instant Review Skip Over UnwantedAutomatic Satellite Programme Recording Aerial connectorOutdoor Unit Satellite Cable Satellite Receiver UnitEngage Auto Satellite Prog REC Mode Press SP/LP on the remote control to set the tape speedBefore performing the following steps SET Edit Mode SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsEdit From a Camcorder SET RECORDER’S Input ModeStart Camcorder Start RecorderAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsSelect Mode Auto SP→LP TimerAuto Timer Playback Activate RepeatRepeat Playback Ntsc PlaybackTelevision Connection To Stereo SystemAudio Cable not provided Audio OUT Mains outletExit Video Channel SET Mode Access Video CHAN- NEL SET ModeVideo Channel Set SET Video ChannelWith RF Connection Access Video Chan NEL SET ModeTuner Set SETAuto Channel Set Procedures Screen preset positionsAfter Scan Completed Is displayed on the screenStoring Channels Manually Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Switch Stations Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetAccess Initial SET Screen Video Plus+ SetupAccess Guide Prog SET Screen Enter Guide Prog NumberRemain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Cassette with the Record Safety tab Blinking Intact Blinks for 10 secondsCheck the programmed data and re Front View IndexTape Speed Indicators display mode of recording light Audio OUT L/R Connectors enableRemote Control VCR, TV Prog +/-,TV +/-, TV Muting Auto Tracking Button enables/disables autoDA4 Double Azimuth helical Maximum recording time
Top Page Image Contents